Free English SONOS BEAM (02) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SONOS BEAM (02) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the controls and indicators on my SONOS BEAM?
Your SONOS BEAM has several touch controls and indicator lights on the top surface. You can use these to control playback and see the speaker’s status.
Controls and Lights Guide:
| Control/Indicator | Function |
| Volume control | Touch for small adjustments or touch and hold to quickly change the volume. • Volume up (right) • Volume down (left) Note: You can also use the app, Alexa, or remote control. |
| Play/Pause | Touch to play or pause sound. |
| Next/Previous (Music only) | • Swipe right across the touch controls to skip to the next song. • Swipe left to go to the previous song. Note: You can’t skip forward or go back when listening to a radio station. |
| Microphone indicator | • Tap the microphone light to turn the microphone on or off. • When the light is on, voice control is on and you can use voice commands. • When the light is off, voice control is off. Note: If the light is off, press and hold the Microphone indicator to talk to Alexa. Release the button to turn voice control off again. |
| Status light | Indicates the status. If the light is distracting, you can turn it off in your room’s settings. |
Note: If you don’t want anyone (like a child) to control playback or change the volume using the speaker touch controls, you can disable them in the room’s settings.
What ports are on the connector panel of the SONOS BEAM?
The connector panel on the back of your SONOS BEAM has the following ports for power and connectivity:
| Port | Description |
| AC power (mains) input | Use only the supplied power cord (using a third-party power cord will void your warranty). Note: Insert the power cord firmly until it is flush with the speaker. |
| Join button | Press to connect during setup. |
| Ethernet port | Use an Ethernet cable if you want to connect to a router, computer, or network-attached storage (NAS) device (optional). |
| HDMI port | Use to connect the soundbar to your TV. |
Where should I place my SONOS BEAM?
You can mount your SONOS BEAM to a wall above or below your TV or place it on a credenza.
Placement on a credenza:
• Place horizontally on a stable and level surface at least 2″ (50mm) from the TV.
• Don’t place vertically or on its side.
• Don’t block the TV’s IR sensor.
• If put on a shelf, place at the front and keep 2″ (minimum) clearance on both sides for best sound quality.
• Keep 1″ (25mm) space (minimum) above Beam so you can reach the touch controls.
• For best sound quality, keep both ends of Beam at least 1′ (30cm) from a wall or other obstruction.
Wall mounting:
To put Beam on a wall, use the appropriate wall mount kit following the provided instructions.
How do I connect the cables to my SONOS BEAM for initial setup?
Follow these steps to connect the cables to your SONOS BEAM.
Before you start:
1. Disconnect existing home theater or surround sound equipment from your TV.
2. Connect any external devices, like a cable box or DVD player, directly to your TV.
Connect the power cord:
1. Insert the power cord firmly into the SONOS BEAM’s AC (mains) power port until it is fully connected.
2. Plug the other end of the power cord into an AC (mains) power source.
Caution: Use only the supplied power cord (using a third-party power cord will void your warranty).
Connect Beam to your TV:
Use the HDMI cable to connect the soundbar to your TV. You may need the optical adapter too (the app lets you know).
1. Fully insert the HDMI cable into the SONOS BEAM’s HDMI port.
2. Connect the other end of the HDMI cable to your TV. You have two choices depending on your TV’s ports.
How do I connect my SONOS BEAM to a TV that has an HDMI ARC port?
HDMI ARC is a special port that looks like a standard HDMI port. Although they look the same, if you connect to a standard HDMI port, you won’t hear sound.
1. On your TV’s audio OUT panel, look for an HDMI ARC port. It may be on the back or side of your TV. You’ll know it’s an ARC port if you see the word “ARC” on the label.
2. Connect the HDMI cable from your SONOS BEAM to the TV’s HDMI ARC port.
Note: If you can’t find the word “ARC” on the label, it isn’t the correct port.
My TV doesn’t have an HDMI ARC port. How do I connect my SONOS BEAM?
If your TV doesn’t have an HDMI ARC port, you’ll need to use the included optical audio adapter to connect your SONOS BEAM.
1. Remove the protective cap from the optical adapter.
2. Attach the optical adapter to the HDMI cable.
3. Connect the optical adapter to the TV’s optical digital OUT port.
Note: The optical adapter’s port is “D-shaped”. Make sure the connector aligns correctly into the port. Inserting the adapter incorrectly may damage the cable.
How do I use the microphone on my SONOS BEAM?
You can control the microphone on your SONOS BEAM using the microphone touch control.
• Touch the microphone icon to turn the microphone on and off. (If you don’t have a voice service installed, the microphone is inactive.)
• When the microphone light is on, voice control is on and Alexa is ready to respond.
• When the microphone light is off, voice control is off.
If you’ve installed a voice service and the microphone is off, you can still use voice commands. Just press and hold the microphone icon while talking to Alexa; no need to start with a wake word. When you release the mic button, voice control turns off again.
What are the guidelines for wall mounting the SONOS BEAM?
To properly wall mount your SONOS BEAM, please follow these guidelines:
• Use the Beam wall mount kit. You can follow the instructions in the kit.
• Keep 1″ (25mm) space (minimum) above the SONOS BEAM so you can reach the touch controls.
• If you’re mounting above the TV, make sure you can reach the touch controls.
• For best sound quality, keep both ends of the SONOS BEAM at least 1′ (30cm) from a wall or other obstruction.
The wall mount kit for the SONOS BEAM includes:
• Wall mount bracket
• 4 wall anchors
• 4 wall screws
• 2 screws
Note: Don’t discard the template. It may look like packing material.
How do I install the wall mount for my SONOS BEAM?
Follow these steps to mount your SONOS BEAM on a wall:
1. Tape the cardboard template to the wall above or below your TV. Use a level. Keep 1″ (25mm) space (minimum) for access to the SONOS BEAM’s touch controls. (Don’t install Beam vertically.)
2. Mark the center of the mounting holes and remove the template.
3. Use a 5/16″ drill bit to drill pilot holes.
4. Insert and secure the wall anchors (don’t use the anchors if drilling into wood).
5. Place the bracket on the wall and loosely tighten the wall screws to secure the bracket. Check with a level and then tighten the screws.
6. Connect the power and HDMI cables to the SONOS BEAM.
7. Place the SONOS BEAM on the bracket.
8. Insert and tighten the SONOS BEAM to the bracket using the mounting screws.
What are the correct drill bit sizes for wall mounting the SONOS BEAM?
Use the following table to determine the correct pre-drill size and whether to use wall anchors for your SONOS BEAM.
| Wall Material | Pre Drill | Use Wall Anchors | Use Screws |
| Wood Stud | 1/8″ / 3 mm bit | No | Yes |
| Drywall (no stud) | 5/16″ / 8 mm bit | Yes | Yes |
| Hard wallboard or double board | 5/16″ / 8 mm bit | Yes | Yes |
| Plaster | 5/16″ / 8 mm bit | No, requires toggle bolt | Yes |
| Concrete or Brick | 5/16″ / 8 mm bit | Yes | Yes |
What are the audio specifications for the SONOS BEAM?
| Feature | Description |
| Amplifier | Five Class-D digital amplifiers. |
| Elliptical Woofer | Four full-range woofers ensures you’ll hear the faithful playback of mid-range vocal frequencies plus deep, rich bass. |
| Tweeter | One tweeter creates a crisp and clear high-frequency response. |
| Microphones | • Five far-field microphone array uses for advanced beam forming and multichannel echo cancellation. • LED hard-wired to voice microphones for privacy control so you know when the microphone is active. |
| Voice Control | Integrated voice control. |
| System Requirements | TV with HDMI ARC or optical digital audio output, broadband internet, and the Sonos app. |
What are the general and networking specifications for the SONOS BEAM?
Networking Specifications:
| Wireless Connectivity | Connects to your WiFi network. |
| Ethernet Port | One 10/100 Mbps Ethernet port. You can plug a Sonos product directly into your router if your WiFi is unstable. |
General Specifications:
| Power Supply | Auto-switching 100-240 V, 50-60 Hz 2.5A AC universal input. |
| Dimensions (H x W x D) | 2.68 x 25.63 x 3.94 in. (68 x 651 x 100 mm) |
| Weight | 6.2 lb (2.8 kg) |
| Operating Temperature | 32°F to 104° F (0° C to 40° C) |
| Storage Temperature | -4°F to 122° F (-20° C to 50° C) |
| Control | Use your remote control, voice, touch controls or the Sonos app. |
| Supported Devices | Connects to TV with HDMI cable (with or without an attached optical adapter). Plays sources connected to the TV, including cable boxes and game consoles. |
| Package Contents | SONOS BEAM, AC power cord, HDMI cable, optical adapter, Quickstart Guide. |
How can I expand my SONOS BEAM into a home theater system?
The SONOS BEAM is expandable. You can add a Sub and two Sonos speakers (like Play:1s) for 5.1 surround sound. It is easy to turn two Sonos speakers (same model) into separate right and left channels for your home theater.
What home theater sound settings can I adjust for my SONOS BEAM?
You can use the Sonos app to adjust sound settings or change the way your SONOS BEAM works with your TV. When you add speakers as surrounds, surround sound is optimized for your room. You can adjust these settings:
Surround Settings:
| Surrounds | Turn surround sound On or Off. |
| TV Level | Adjust surround volume for TV audio. |
| Music Level | Adjust surround volume for music. |
| Music Playback | Ambient (subtle) or Full (louder, full range). Doesn’t apply to TV audio. |
| Balance Surround Speakers | Manually balance your surround speakers. |
Home Theater Settings:
| TV dialog settings | If the TV audio is out of sync with the video, you can adjust the audio delay (lip sync) in your room’s settings. |
| Group audio delay | If you notice audio issues when playing to a group, you can adjust this setting. |
| TV autoplay | If music or other content is playing when you turn on your TV, the audio automatically switches to TV audio (default). If you don’t want this to happen, turn off TV Autoplay in your room’s settings. |
| Speech enhancement | Makes TV dialog easier to hear. |
| Night sound | Enhances quiet sounds and reduces the intensity of loud sounds. Turn on to reduce the volume while still experiencing proper balance and range. |
| Remote control setup | During setup, you’ll program a remote control. You can program a different remote control any time. |
What are the important safety instructions for using the SONOS BEAM?
Please follow these safety guidelines when using your SONOS BEAM:
1. Read and keep these instructions.
2. Heed all warnings and follow all instructions.
3. If your product is wall-mounted, ensure it is installed correctly to prevent injury. Never hang from the product or bracket and periodically check that screws are tight.
4. Do not use this apparatus near water.
5. Clean only with a dry soft cloth. Household cleaners or solvents can damage the finish.
6. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produce heat.
8. Protect the power cable from being walked on or pinched, particularly at plugs and convenience receptacles.
9. Only use attachments/accessories specified by the manufacturer.
10. Unplug this apparatus during lightning storms or when unused for long periods of time.
11. Refer all servicing to qualified personnel.
12. The Mains plug should be readily available to disconnect the equipment.
13. Warning: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
14. Do not expose the apparatus to dripping or splashing and do not place objects filled with liquids, such as vases, on the apparatus.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD SONOS BEAM (02) PDF DOCUMENT