Free English SECO-LARM ENFORCER SL-1312-SA-B (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SECO-LARM ENFORCER SL-1312-SA-B (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the key features of the SECO-LARM ENFORCER SL-1312-SA-B?
The SECO-LARM ENFORCER SL-1312-SA-B has the following features:
• Synchronized piezo siren and long-life LEDs (x4)
• Surface-mount or mount to single-gang box
• High-impact plastic casing and weather-resistant design allows for indoor and outdoor use
• Available with amber, blue, clear, or red lens
• Simple 2-wire connection: red to positive, black to negative
• Alarm siren sound is 100dB@3ft (1m) at 12VDC
What is included in the Parts List for the SECO-LARM ENFORCER SL-1312-SA-B?
The package for the SECO-LARM ENFORCER SL-1312-SA-B includes:
1x Mini Strobe Siren
2x Wall anchors
2x Mounting screws
1x Manual
What are the different models available for the SECO-LARM ENFORCER SL-1312-SA-B based on lens color?
| Color | Model | Color | Model |
|---|---|---|---|
| Amber | SL-1312-SA/A | Blue | SL-1312-SA/B |
| Clear | SL-1312-SA/C | Red | SL-1312-SA/R |
What are the technical specifications for the SECO-LARM ENFORCER SL-1312-SA-B?
| Lens color | Amber, Blue, Clear, or Red |
| Rated voltage | 12VDC |
| Operating Voltage | 6~15 VDC |
| Current draw | 60mA@12VDC |
| Flashing speed | 360~480 per min (not adjustable) |
| Siren | Piezo, 100dB@3ft (1m) at 12VDC |
| Connections | Red to positive Black to negative |
| Electrical protection | Reverse polarity protection |
| Operating temperature | -4°~158° F (-20°~70° C) |
| Dimensions | 2 7/8″x4 7/8″x1 7/8″ (73x123x47 mm) |
How do I install the SECO-LARM ENFORCER SL-1312-SA-B?
Follow these steps to install your SECO-LARM ENFORCER SL-1312-SA-B:
1. Consider the type of mounting and where to run the wires. The two connection wires exit the device from the lower part of the device back but also with a notch at the bottom to allow for hidden or exposed wiring.
2. Run two wires from an N.C. output of the triggering device to the Mini Strobe Siren installation location.
3. For surface mounting, mark and drill the mounting holes and holes for the wiring if needed. NOTE: The Mini Strobe Siren mounting holes are spaced so that it can also be mounted to a standard single-gang back box.
4. Connect the red wire to the positive trigger and the black wire to the negative trigger wire.
5. Use the included mounting screws (and plastic wall anchors if needed) to mount the device taking care not to crimp the wires.
What should I know about the mounting holes and wiring locations for the SECO-LARM ENFORCER SL-1312-SA-B?
The SECO-LARM ENFORCER SL-1312-SA-B has designated mounting holes for securing the device. The connection wiring exits from the lower corner of the device’s back. The mounting holes are spaced to allow for mounting on a standard single-gang back box in addition to surface mounting.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD SECO-LARM ENFORCER SL-1312-SA-B (01) PDF DOCUMENT