SCARLETT SC-VC80C02 (01) PDF Document

The parts of the SCARLETT SC-VC80C02 are described as follows:

1. Wheel

2. Dust collector

3. Dust collector handle

4. Dust collector cover

5. Sucking inlet

6. Dust collector bottom release button

7. Dust collector bottom

8. Dust collector lock button

9. ON/OFF button

10. Power cord winding button

11. Power level selector

12. Outlet HEPA filter

13. Main HEPA filter

14. Filter sponge

15. FLOOR/CARPET nozzle

16. FURNITURE nozzle

17. SLOT nozzle

18. Retractable tube

19. Retractable tube length adjuster

20. Hose

21. Hose locks

22. Hose base

23. Hose air flow control switch

24. Power cord and plug

To prepare the SCARLETT SC-VC80C02 for use, follow these steps:

1. Unpack the device and remove the sticker from the body.

2. To connect the hose to the vacuum cleaner, insert the hose base into the sucking inlet and press gently until it clicks. To disconnect the hose, press the two locks located at the hose base sides.

3. Pull out the retractable tube until the necessary length is reached. For this purpose, move the retractable tube length adjuster and pull out the tube end.

4. Insert the hose into the tube.

5. Attach one of the nozzles to the tube.

The SCARLETT SC-VC80C02 comes with three specific nozzles:

The “FLOOR/CARPET” combined nozzle: Designed for carpet mats and similar floor coatings, and for flat surfaces.

The “FURNITURE” nozzle: Designed for cleaning upholstered furniture, curtains, and decorative surfaces.

The “SLOT” nozzle: Designed for cleaning in areas that are not easily accessible, such as corners or narrow slots.

Follow these instructions to operate the SCARLETT SC-VC80C02:

1. Before starting, unwind the cord to a sufficient length and insert the plug into the power supply. The yellow mark on the cord shows the optimal cord length. Do not unwind the cord beyond the red mark.

2. Press the On/Off button to switch the unit on and press it again to stop it.

3. You can adjust the vacuum cleaner power using the power control on the housing.

4. To rewind the cord, press the rewind button and guide the cord with your hand to ensure that it does not whip, which could cause damage.

You can adjust the airflow on the SCARLETT SC-VC80C02 using the air flow regulator located on the flexible hose handle:

Decrease the flow for cleaning curtains, books, furniture, etc.

Increase the flow for cleaning bare floors.

When using the SCARLETT SC-VC80C02, observe the following safeguards:

Check that the voltage indicated on the rating label corresponds to the mains voltage in your home before first use.

Do not use outdoors or on wet surfaces to reduce the risk of electric shock.

Do not handle the plug with wet hands.

Never switch off the appliance by pulling the cord.

Do not let the cord hang over sharp edges or touch hot surfaces.

Always unplug the appliance when not in use and before servicing.

Do not use the appliance with a damaged cord or other defects.

Do not leave the appliance exposed to direct sunlight or near any heater to avoid plastic deformation.

To avoid damage to the flexible hose, do not fold or pull it strongly.

Do not put any object into air outlets or use with the outlet blocked. Keep free of dust, hair, and anything that may reduce airflow.

CAUTION: To avoid voltage overload, do not plug the unit and other powerful electrical appliances into the power supply at the same time.

Never use the vacuum cleaner without filters.

Do not use the appliance on wet surfaces; this unit does not absorb water.

If you have cleaned a carpet with liquid detergent, let the carpet dry up completely before vacuuming it.

Never use the appliance without the dust bin. Replace the dust bin without delay if it is damaged.

To prevent motor overheating on the SCARLETT SC-VC80C02, do not work continuously longer than 30 minutes. It is obligatory to stop the vacuum cleaner for no less than 15 minutes after this period.

To clean the dust collector on the SCARLETT SC-VC80C02:

1. Disconnect the vacuum cleaner from the mains.

2. Detach the dust collector by pressing the dust collector lock button.

3. Empty the dust collector by pressing the dust collector release button.

Clean the filters of the SCARLETT SC-VC80C02 at least once a year. If the vacuum cleaner is used frequently, wash the filters after each 3 to 5 dust collector cleaning operations. Follow these steps:

1. Disconnect the vacuum cleaner from the mains.

2. Open the dust collector cover and remove the main filter.

3. Wash all plastic parts and the sponge of the filter with warm running water, then dry them thoroughly.

4. After cleaning, insert the filter into place and close the dust collector cover by rotating it clockwise.

5. Remove the rear grill and take out the outlet filter.

6. Wash the filter with running water and dry it thoroughly.

7. After cleaning, insert the filter into place.

WARNING: Do not use the vacuum cleaner with no filters attached! This may lead to damage to the electric motor. Do not wash the filters in a washing machine and do not dry them with a hair dryer.

To store the SCARLETT SC-VC80C02:

Place the appliance vertically.

Insert the tube into the special holder on the body.