SAVO NOPPA 2.0 (02) PDF MANUAL

Warning! Before proceeding with installation, read the safety information in the User Manual.

The package for your SAVO NOPPA 2.0 includes the following parts as shown in the installation manual:

H1: Flap valves (2x)

I: Wall plugs (5x)

L: Screws (5x)

B: Screws (4x)

C: Screws (6x)

Q: Chimney brackets (2x)

M: Air outlet support brackets (2x)

B5: Support bracket (1x)

O1: Air outlet connection for recirculation (1x)

O: Reducer flange (1x)

N1: Upper chimney section (1x)

N2: Lower chimney section (1x)

Z: Grease filter (1x)

The main hood body is also included.

Before installing your SAVO NOPPA 2.0, please note the following requirements:

• **Manpower:** The installation should be carried out by two people.

• **Safety Gear:** Wear protective gloves during the installation process.

• **Minimum Distance:** The minimum distance from the cooking surface to the bottom of the hood must be observed:

– For electric hobs: 500 mm

– For gas hobs: 650 mm

To prepare the wall for your SAVO NOPPA 2.0, follow these steps:

1. Draw a vertical line on the wall at the center of your cooking area where the hood will be installed.

2. Mark the drilling points for the hood and chimney brackets on this line. Use the upper chimney (N1) as a guide for marking the upper bracket holes. Refer to the dimensional drawings in the manual for precise measurements.

3. Mark the holes for the main hood support screws (X, Y).

4. Drill the required holes. The manual specifies using an Ø 8 mm drill bit for the bracket holes and an Ø 12 mm drill bit for the main support screw holes.

To mount the SAVO NOPPA 2.0 hood and brackets:

1. Insert the wall plugs (I) into the Ø 8 mm drilled holes.

2. Fix the two chimney brackets (Q) to the wall using screws.

3. Insert the main support screws into the Ø 12 mm holes.

4. Hang the main body of the hood onto the two main support screws.

5. Adjust the hood so it is level.

6. Secure the hood from the inside with one screw (L).

For a ducted installation of your SAVO NOPPA 2.0, follow these instructions:

1. **Select Duct Size:**

– For Ø 150 mm ducting: Install the two half-flaps (H1) into the air outlet on top of the hood.

– For Ø 120 mm ducting: First, fit the reducer flange (O) onto the air outlet, then install the two half-flaps (H1).

2. **Connect Ducting:** Attach the flexible ducting hose to the air outlet on the hood.

3. **Secure Hose:** Secure the upper end of the ducting hose to the wall support bracket using 4 screws (L).

To assemble the chimney for a ducted installation:

1. Slide the upper chimney section (N1) down over the ducting and secure it to the top chimney bracket.

2. Secure the lower part of the hood to the wall bracket with 4 screws (B).

3. Fix the hood body from the top using 4 screws (C).

4. Slide the lower chimney section (N2) over the hood body until it rests on top. Ensure it fits inside the upper chimney (N1).

5. Secure the lower chimney (N2) to the main body from the sides using 2 screws (C).

For a recirculation installation of your SAVO NOPPA 2.0:

1. Install the two support brackets (M) onto the air outlet connection (O1) using 2 screws (L).

2. Mount the air outlet connection (O1) to the wall at the desired height.

3. Attach one end of a flexible ducting hose to the air outlet on the hood and the other end to the lower opening of the mounted air outlet connection (O1).

4. Slide the upper chimney (N1) down over the hose, aligning the side vents on the chimney with the outlets on the air outlet connection (O1). Secure the chimney with 4 screws (B).

5. Install the two optional charcoal filters (W) onto the motor assembly. These filters are necessary for recirculation and may be sold separately. To install, align them with the motor housing and turn them until they lock into place.

6. Proceed with the final chimney and filter assembly steps.

The final step for both installation types is to install the grease filter (Z). Hook the filter into the rear of the opening on the underside of the hood and push it upwards at the front until it clicks securely into place.