SANYO PLC-XF12BL (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD SANYO PLC-XF12BL (01) PDF MANUAL


PDF Content Summary: Multimedia Projector

MODEL PLC-XF12N/12NL PLC-XF12E/12EL PLC-XF12B/12BL Owner's Manual

TO THE OWNER Before operating this projector, read this manual thoroughly and operate the projector properly. This projector provides many convenient features and functions. Operating the projector properly enables you to manage those features and maintains it in better condition for a considerable time. Improper operation may result in not only shortening the product-life, but also malfunctions, fire hazard, or other accidents. If your projector seems to operate improperly, read this manual again, check operations and cable connections and try the solutions in the “Trouble-shooting” section of the end of this booklet. If the problem still persists, contact the sales dealer where you purchased the projector or the service center. SAFETY PRECAUTIONS WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. ● This projector produces intense light from the projection lens. Do not stare directly into the lens as possible. Eye damage could result. Be especially careful that children do not stare directly into the beam. ● This projector should be set in the way indicated. If not, it may result in a fire hazard.

● Take appropriate space on the top, sides and rear of the projector cabinet for allowing air circulation and cooling the projector. 20cm Minimum distance should be taken. If the projector is to be built into a compartment or similarly enclosed, the minimum distances must be maintained. Do not cover the ventilation slot on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. SIDE and TOP REAR50cm 50cm 1m

● Do not put any flammable object or spray can near the projector, hot air is exhausted from the ventilation holes. ● The Remote Control Unit, supplied to this projector, emits the laser beam as the Laser Pointer function from the Laser Light Window while pressing the LASER button. Do not look into the Laser Light Window or shine the laser beam on yourself or other people. Eye damage may result. ● If the projector is not to be used for an extended time, unplug the projector from the power outlet. READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE EXCEPT LAMP REPLACEMENT. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT. THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE OWNER'S MANUAL WITH THIS UNIT.

2 SAFETY PRECAUTIONS

All the safety and operating instructions should be read before the product is operated. Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Follow all warnings and instructions marked on the projector. For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges. Do not expose this unit to rain or use near water... for example, in a wet basement, near a swimming pool, etc... Do not use attachments not recommended by the manufacturer as they may cause hazards. Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. Slots and openings in the back and bottom of the cabinet are provided for ventilation, to insure reliable operation of the equipment and to protect it from overheating. The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register. This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided. Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector. This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company. Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it. Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation. e. If the projector has been dropped or the cabinet has been damaged. f. When the projector exhibits a distinct change in performance-this indicates a need for service. When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons. Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition. Voor de klanten in Nederland Bij dit product zijn batterijen geleverd. Wanneer deze leeg zijn, moet u ze niet weggooien maar inleveren als KCA.

3 COMPLIANCES Federal Communication Commission Notice This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. AC POWER CORD REQUIREMENT The AC Power Cord supplied with this projector meets the requirement for use in the country you purchased it. AC Power Cord for the United States and Canada : AC Power Cord used in the United States and Canada is listed by the Underwriters Laboratories (UL) and certified by the Canadian Standard Association (CSA). AC Power Cord has a grounding-type AC line plug. This is a safety feature to be sure that the plug will fit into the power outlet. Do not try to defeat this safety feature. Should you be unable to insert the plug into the outlet, contact your electrician. GROUND AC Power Cord for the United Kingdom : This cord is already fitted with a moulded plug incorporating a fuse, the value of which is indicated on the pin face of the plug. Should the fuse need to be replaced, an ASTA approved BS 1362 fuse must be used of the same rating, marked thus . If the fuse cover is detachable, never use the plug with the cover omitted. If a ASA replacement fuse cover is required, ensure it is of the same colour as that visible on the pin face of the plug (i.e. red or orange). Fuse covers are available from the Parts Department indicated in your User Instructions. If the plug supplied is not suitable for your socket outlet, it should be cut off and destroyed. The end of the flexible cord should be suitably prepared and the correct plug fitted. (See Over) WARNING : A PLUG WITH BARED FLEXIBLE CORD IS HAZARDOUS IF ENGAGED IN A LIVE SOCKET OUTLET. The Wires in this mains lead are coloured in accordance with the following code: Green-and-yellow ············ Earth Blue ································· Neutral Brown ······························ Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows: The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by the letter E or by the safety earth symbol or coloured green or green-and-yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. WARNING : THIS APPARATUS MUST BE EARTHED. THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND EASILY ACCESSIBLE. 4 TABLE OF CONTENTS

FEATURES AND DESIGN 6 PREPARATION 7 NAME OF EACH PART OF THE PROJECTOR 7 SETTING-UP THE PROJECTOR 8 CONNECTING THE AC POWER CORD 8 POSITIONING THE PROJECTOR 9 PICTURE LEVEL AND TILT ADJUSTMENT 10 MOVING THE PROJECTOR 10 CONNECTING THE PROJECTOR 11 TERMINAL OF THE PROJECTOR 11 CONNECTING THE COMPUTER 13 CONNECTING THE VIDEO EQUIPMENT 21 BEFORE OPERATION 23 CONTROLS AND INDICATORS 23 OPERATION OF THE REMOTE CONTROL 25 WIRELESS REMOTE CONTROL UNIT 25 WIRELESS/WIRED REMOTE CONTROL UNIT 28 OPERATING ON-SCREEN MENU 30 HOW TO OPERATE ON-SCREEN MENU 30 FLOW OF ON-SCREEN MENU 30 MENU BAR 31 BASIC OPERATION 32 TURNING ON / OFF THE PROJECTOR 32 TO TURN ON THE PROJECTOR 32 TO TURN OFF THE PROJECTOR 32 ADJUSTING THE IMAGE 33 ZOOM ADJUSTMENT 33 FOCUS ADJUSTMENT 33 LENS SHIFT FUNCTION 33 DIGITAL ZOOM FUNCTION 33 NORMAL PICTURE FUNCTION 33 FREEZE PICTURE FUNCTION 34 NO SHOW FUNCTION 34 P-TIMER FUNCTION 34 AUTO IMAGE ADJUSTMENT 34 CURSOR FUNCTION 34 SOUND ADJUSTMENT 35 DIRECT OPERATION 35 MENU OPERATION 35 TRADEMARKS COMPUTER MODE 36 SELECTING COMPUTER MODE 36 SELECTING COMPUTER SYSTEM 36 COMPATIBLE COMPUTER SPECIFICATIONS 37 PC ADJUSTMENT 38 PICTURE IMAGE ADJUSTMENT 40 NORMAL FUNCTION 41 AUTO IMAGE ADJUSTMENT 41 PICTURE POSITION ADJUSTMENT 42 PICTURE SCREEN ADJUSTMENT 43 VIDEO MODE 44 SELECTING VIDEO MODE 44 SELECTING VIDEO SOURCE 44 SELECTING COLOR SYSTEM 45 PICTURE IMAGE ADJUSTMENT 46 NORMAL FUNCTION 47 PICTURE SCREEN ADJUSTMENT 47 SETTING 48 SETTING MENU 48 SETTING LANGUAGE 49 APPENDIX 50 OPERATING WIRELESS MOUSE 50 MAINTENANCE 51 TEMPERATURE WARNING INDICATOR 51 AIR FILTER CARE AND CLEANING 51 LAMP REPLACEMENT 52 CLEANING THE PROJECTION LENS 53 TROUBLESHOOTING 53 TECHNICAL SPECIFICATIONS 55

● Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer,Inc. ● IBM and PS/2 are trademarks or registered trademarks of International Business Machines, Inc. ● Windows and PowerPoint are registered trademarks of Microsoft Corporation. ● Each name of corporations or products in the owner's manual is a trademark or a registered trademark of its respective corporation. 5 FEATURES AND DESIGN This Multimedia Projector is designed with the most advanced technology for portability, durability, and ease of use. The projector utilizes built-in multimedia features, a palette of 16.77 million colors, and matrix liquid crystal display (LCD) technology.

◆ Compatibility This projector widely accepts various video and computer input signals including; ● Computers IBM-compatible and Macintosh computers up to 1280 x 1024 resolution. ● 6 Color Systems NTSC, PAL, SECAM, NTSC 4.43, PAL-M or PAL N color system can be connected. ● S-Video S-Video signals, such as a S-VHS VCR output signals, can be connected. ◆ High Resolution Image This projector provides 1024 x 768 dots resolution for computer input and 800 horizontal TV lines. The resolution from the computer between 1024 x 768 and 1280 x 1024 is compressed into 1024 x 768 dots. This projector cannot display image of over 1280 x 1024 dots. When the resolution of your computer is over than 1280 x 1024, reset the computer output for lower resolution. ◆ Multi-Scan System This projector has Multi-Scan System to conform to almost all computer output signals quickly. There is no need for troublesome manual adjustment of frequency and other settings. ◆ One-Touch Auto Imaging Incoming computer video signals are recognized and the best setting is automatically selected by the Auto Image adjustment. No complicated setup is necessary and projection is always precise. ◆ Multilanguage Menu Display Operation menu is displayed in; English, Deutsch, Français, Italiano, Español, or Japanese. ◆ Digital Zoom (Computer Mode only) The Digital Zoom magnifies the image up to 16 times, allowing you to focus on crucial information at a presentation. ◆ Motor-driven Lens Shift The projection lens can be moved up and down with the motor-driven lens shift function. This function makes it easy to provide the projected image where you want. The zoom and focus can be also adjusted with motor driven operation. ◆ Power Management Power Management function is provided to reduce power consumption while the projector is not in use. This Power Management function operates to turn the Projection Lamp off when the projector detects signal interruption and any button is not pressed over 5 minutes. The Projection Lamp is automatically turned on again when the projector detects the signal or any operation button is pressed. This projector is shipped with this function ON. ◆ Laser Pointer Function The Wireless Remote Control Unit supplied with this projector includes the Laser Pointer function. This function helps you to make a smart presentation on a projected screen. ◆ Wireless Mouse The Wireless Remote Control Unit supplied with this projector has Wireless Mouse function for the connected computer. This function enables you to operate both projector and computer with this Wireless Remote Control Unit only. ◆ Accessories The projector comes with the parts listed below. Check to find all the parts are included. If any parts are missing, contact an authorized dealer or service station. ● Owner's Manual. ● AC Power Cord. ● Wireless Remote Control Unit. ● Wireless/Wired Remote Control Unit. ● Remote Control Cable. ● Batteries for Remote Control Units. ● VGA Cable. ● Mouse Cable for PS/2 port. ● Mouse Cable for serial port. ● Mouse Cable for ADB port. ● VGA/MAC Adapter. ● Protective Dust Cover ● Lens Cover.

6 PREPARATION NAME OF EACH PART OF THE PROJECTOR FRONT OF THE PROJECTOR INFRARED REMOTE RECEIVER PROJECTION LENS REMOVABLE

LENS COVER REAR OF THE PROJECTOR EXHAUST VENT HOT AIR EXHAUSTED ! Air blown from the exhaust vent is hot. Observe the following when handling your projector or choosing a location to install it. ● Keep heat-sensitive objects away from the exhaust port. ● If you set the projector on top of a metallic surface, the surface will become hot because of the hot air exhaust. Be careful when handling. ● Do not touch the cabinet near to the SPEAKERS LAMP COVER CARRYING HANDLE MAIN ON / OFF

exhaust vent area, and especially screws and metallic parts. These parts will become INFRARED SWITCH

hot while the projector is used. This projector detects the internal temperature and automatically controls the operating power of the Cooling Fans. BOTTOM OF THE PROJECTOR REMOTE RECEIVER AIR INTAKE VENT AIR INTAKE VENT POWER CORD CONNECTOR ADJUSTABLE FEET

7 PREPARATION SETTING-UP THE PROJECTOR CONNECTING THE AC POWER CORD This projector uses nominal input voltages of 100-120 V or 200-240 V AC. The projector automatically selects the correct input voltage. It is designed to work with single-phase power systems having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. Consult your authorized dealer or service station if you are not sure of the type of power supply being in use. Connect the projector with the peripheral equipment before turning the projector on. (Refer to pages 13 ~ 22 for connection.) Connect the AC Power Cord (supplied) to the projector. The AC outlet must be near this equipment and must be easily accessible. NOTE ON THE POWER CORD The AC Power Cord must meet the requirement of the country where you use the projector. Confirm the AC plug type with the chart below and the proper AC power cord must be used. If the supplied AC Power Cord does not match the AC outlet, contact your sales dealer. Projector side AC Outlet side For the U.S.A. and Canada For Continental Europe For the U.K. Ground

To the POWER CORD CONNECTOR on the projector. To the AC Outlet. (120 V AC) To the AC Outlet. (200 - 240 V AC) To the AC Outlet. (200 - 240 V AC)

8 PREPARATION POSITIONING THE PROJECTOR ● This projector is basically designed to project on a flat projection surface. ● This projector can be focused from 4.9' (1.5 m) ~ 80.7' (24.6 m). ● Refer to the figure below as an example when positioning the projector to the screen. THIS PROJECTOR SHOULD BE SET IN THE WAY INDICATED. NEVER HANG THE PROJECTOR, OR FALL DOWN ON ITS SIDE. IT MAY RESULT IN FIRE HAZARD.

ROOM LIGHT The projector should be placed in a room with limited light. Picture quality will be directly affected by lightning conditions. 40" Maximum Zoom Minimum Zoom 400" 100" 150" 200"300" 77" 115" 154" 231" 308" DISTANCE 600" 462"

Screen Size Max. Zoom Min. Zoom 40" 100" 77" 150" 115" 200" 154" 300" 231" 400" 308" 600" 462"

Distance VENTILATION 4.9' (1.5 m) 13.1' (4.0 m) 20' (6.1 m) 26.9' (8.2 m) 40' (12.2 m) 53.8' (16.4 m) 80.7' (24.6 m)

This projector is equipped with a cooling fan to protect it from overheating. Pay attention to the following to ensure the ventilation and avoid a possible risk of fire and malfunction. ● Do not cover the vents with papers or other materials. ● Keep the rear grill at least 3.3' (1m) away from any object. ● Make sure that there are no objects under the projector. An object under the projector may prevent the projector from taking the cooling air through the bottom vent. AIR INTAKE VENT (BOTTOM SIDE) EXHAUST VENT (REAR SIDE)

9 PREPARATION PICTURE LEVEL AND TILT ADJUSTMENT

Picture tilt and projection angle can be adjusted by twisting ADJUSTABLE FEET. Projection angle can be adjusted up to 4 degrees by rotating Adjustable Feet. DOWN MOVE THE PROJECTED IMAGE POSITION Adjust the projected image position (maximum 760mm downward or upward on the 100" screen) by using lens shift function. (See page 33.) m m 0 6 7 100" SCREEN UP UP ADJUSTABLE FEET DOWN m m 0 6 7 MOVING THE PROJECTOR

Use the carry handle when moving the projector. Replace the lens cover and rotate the adjustable feet fully clockwise. CAUTION IN CARRYING OR TRANSPORTING THE PROJECTOR ● Do not drop or bump the projector, otherwise damages or malfunctions may result. ● When carrying the projector, use a suitable carrying case. ● Do not transport the projector by using a courier or transport service in an unsuitable transport case. This may cause damage to the projector. To transport the projector through a courier or transport service, consult your dealer and best case should be applied. 10 CONNECTING THE PROJECTOR TERMINAL OF THE PROJECTOR SIDE OF THE PROJECTOR (CONNECT THE COMPUTER) 2 1 9 8 6 5 1 10 DIGITAL - USB 1 AUDIO 1

11 CONTROL PORT 1 R L (MONO) ANALOG N I R ET UP M O C 2- 3

USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) N RGB H V I R E T U P M O C R/C JACK SERIAL PORT AUDIO OUT R L ANALOG RGB T U O R ET UP M OC 4

13 12 7

1 8 COMPUTER INPUT-1 TERMINAL (ANALOG HDB 15-PIN) Used to connect a computer to the projector. 2 9 COMPUTER INPUT-1 TERMINAL (DIGITAL MDR 20-PIN) Used to connect a computer to the projector. 3 10 COMPUTER INPUT-2 JACKS (BNC TYPE x 5) Used to connect a computer to the projector. 11 4 MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN) Used to connect a monitor to the projector. 5 12 COMPUTER AUDIO INPUT-1 JACKS (R and L) Used to connect an audio output from the computer to the projector. 13 6 COMPUTER AUDIO INPUT-2 JACKS (R and L) Used to connect an audio output from the computer to the projector. 7 AUDIO MONITOR OUTPUT JACKS (R and L) Used to connect an audio input from audio equipment to the projector. CONTROL PORT-1 CONNECTOR Used to connect a mouse cable to the projector. CONTROL PORT-2 CONNECTOR Used to connect a mouse cable to the projector. USB PORT-1 CONNECTOR Used to connect a computer to the projector. USB PORT-2 CONNECTOR Used to connect a computer to the projector. SERIAL PORT TERMINAL (DB9) Used to connect a computer to the projector. WIRED REMOTE JACK When using the wired remote control, connect the remote cable to this jack.

11 CONNECTING THE PROJECTOR SIDE OF THE PROJECTOR (CONNECT THE VIDEO EQUIPMENT) 15 18

14 17 20 1 VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO - N I O E D I V 2 VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO - N I O E D I V T U VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO O R O T I N O M 21 AUDIO R L (MONO) AUDIO R L (MONO) AUDIO R L 16 19 22

14 15 16 17 18 VIDEO INPUT JACKS-1 (BNC TYPE x 3) Used to connect a video source to the projector. S-VIDEO INPUT JACK-1 Used to connect a S-VHS video source to the projector. AUDIO INPUT JACKS-1 (R and L) Used to connect an audio source to the projector. VIDEO INPUT JACKS-2 (BNC TYPE x 3) Used to connect a video source to the projector. S-VIDEO INPUT JACK-2 Used to connect a S-VHS video source to the projector. 19 20 21 22 AUDIO INPUT JACKS-2 (R and L) Used to connect an audio source to the projector. VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3) Permits video connection to a monitor. VIDEO MONITOR (S-VIDEO) OUTPUT JACK Permits S-VHS video connection to a monitor. AUDIO MONITOR OUTPUT JACKS (R and L) Permits audio connection to a monitor.

12 CONNECTING THE PROJECTOR CONNECTING THE COMPUTER CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (ANALOG HDB 15-PIN) Personal computers can be connected to the HDB15-pin (VGA) terminal on the projector. ● Connect the computer to these terminals using the VGA cable and VGA/MAC adapter (provided). CAUTION: For projectors, the VGA cable provided is designed to reduce RFI (Radio Frequency Interference) emissions. For regulatory compliance reasons, this cable must be used and must not be replaced by any other cable. CONNECTING TO THE COMPUTER INPUT 1 TERMINAL (DIGITAL MDR 20-PIN) Digital output signal from the computer can be connected to the DIGITAL terminal (MDR 20-pin). When using this input, Graphic Accelerator Board designed for this projector should be installed into your computer and set-up the computer configuration following instruction included in the Graphic Accelerator Board package. Refer to DIGITAL INPUT CONNECTION on page 16 and 18. CONNECTING TO THE COMPUTER INPUT 2 JACKS (BNC x 5) Personal computers can be connected to the computer input (Red, Green, Blue, Horiz. Sync. and Vert. Sync.) on the projector. ● Connect the computer to these jacks using the BNC cables (not provided). CONNECTING TO THE COMPUTER AUDIO INPUT JACKS (1 and 2) ● Connect audio outputs from your computer to these jacks using the audio cable (not provided). CONNECTING TO THE MULTI-POLE 12-PIN (CONTROL PORT) CONNECTORS (1 and 2) ● When the computer is operated by projector's remote control unit, connect three different type of cables (provided) between projector control port and computer mouse port or serial port.

COMPUTER TYPE IBM Compatible computer with PS/2 mouse port. IBM Compatible computer with serial port. Apple Macintosh computer with ADB mouse port. CABLE Mouse Cable for PS/2 port. Mouse Cable for Serial port. Mouse Cable for ADB port.

■ CONTROL PORT PS/2 Port Serial Port ADB Port

2 5 6 143 1 2 3 4 5 6 –––––––– CLK DATA –––––––– –––––––– –––––––– T x D –––––––– –––––––– –––––––– –––––––– –––––––– –––––––– ADB –––––––– –––––––– –––––––– –––––––– CONTROL PORT CABLE REMOVAL HINT Disconnect control port cable with following steps. 1. Hold the portion (A)

10 7 8 12 11 9 7 8 9 10 11 12 –––––––– –––––––– GND –––––––– –––––––– –––––––– READY –––––––– GND –––––––– –––––––– –––––––– –––––––– –––––––– GND –––––––– –––––––– –––––––– of the connector with one hand. 2. Pull the portion (B) arrow direction and remove connector. B A

13 CONNECTING THE PROJECTOR CONNECTING TO THE MONITOR OUTPUT TERMINAL (ANALOG HDB 15-PIN) This terminal output the information of the selected computer source being viewed on the screen (Computer 1 or Computer 2). When video source ("Video 1" or "Video 2") is selected, this terminal outputs Computer 1 input information. An external monitor can be connected to the HDB15-pin (VGA) terminal on the projector. ● Connect the monitor to this terminal using the VGA cable (not provided).

HDB 15-PIN TERMINAL 54321 10 9 8 7 6 15 14 13 12 11 Pin No./Signal 1 Red input 2 Green input 3 Blue input 4 Sense 2 5 Ground (Horiz.sync.) 6 Ground (Red) 7 Ground (Green) 8 Ground (Blue) Pin No./Signal 9 Non Connect 10 Ground (Vert. sync.) 11 Sense 0 12 Sense 1 13 Horiz. sync 14 Vert. sync 15 Reserved

CONNECTING TO THE AUDIO MONITOR OUTPUT (VARIABLE) JACKS These jacks will contain the audio information of the selected program source being viewed on the screen (Computer 1, Computer 2, Video 1 or Video 2). If you have selected program source Computer 2 the audio signal connected to the Computer 2 audio input jack will be available at the audio monitor output jacks. Use RCA type audio for connection. ● If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks. ● If the audio input of the audio equipment is monaural, connect it to the left jack. CONNECTING TO THE SERIAL PORT (DB 9-PIN) TERMINAL

● If you control the projector by computer, you must connect a cable 1 (not provided) from your computer to this terminal. 2 3 ■ SERIAL PORT 4 DB9-PIN 5 TERMINAL 6 5 4 3 2 1 7 9 8 7 6 8 9 –––––––– R x D T x D –––––––– Ground –––––––– –––––––– –––––––– ––––––––

CONNECTING TO THE USB PORT CONNECTORS (1 and 2)

This port is used to control the projector with the computer. It is also used to control the computer with the Remote control of this projector. (Refer to P49, 50.) ■ USB PORT

Connect the USB port of the computer to this port. 2 1 1 2 Vcc - Data

3 4 3 4 + Data Ground

14 CONNECTING THE PROJECTOR CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER MONITOR CABLE

COMPUTER BNC CABLE x 5 (NOT PROVIDED)

SERIAL PORT PS/2 PORT COMPUTER OUTPUT (BNC TYPE x 5) COMPUTER OUTPUT (HDB15-PIN TYPE) R COMPUTER (NOT PROVIDED) VGA CABLE (PROVIDED) AUDIO CABLE (NOT PROVIDED)

INPUT INPUT AUDIO OUTPUT L COMPUTER

COMPUTER AUDIO INPUT 1 or 2 R L USB 1 AUDIO 1 CONTROL PORT 1 ANALOG INPUT 1 (ANALOG) DIGITAL 1 - NI

R L (MONO) R E T U P M O C MOUSE CABLE FOR 2 -

PS/2 PORT (PROVIDED) USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) RGB H V NI R ET UP M OC COMPUTER INPUT 2

MOUSE CABLE FOR SERIAL PORT (PROVIDED) SERIAL PORT CABLE (NOT PROVIDED) CONTROL PORT OUTPUT 1 or 2 R/C JACK SERIAL PORT SERIAL PORT OUTPUT AUDIO OUT R L COMPUTER ANALOG RGB T U O R ET UP M OC MONITOR OUTPUT

AUDIO AUDIO CABLE (NOT PROVIDED) AUDIO OUTPUT

INPUT SPEAKER OUT L R L R Amp. Speaker (L) Speaker (R)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 15 CONNECTING THE PROJECTOR CONNECTING AN IBM-COMPATIBLE DESKTOP COMPUTER (DIGITAL INPUT CONNECTION) NOTE: This connection need optionally sold Graphic Accelerator Board. For this information, contact to your authorized dealer. Before using with digital connection, install (Plug in) Graphic Accelerator

COMPUTER Board into PCI bus slot of the computer and set up the computer following instructions in the Graphic Accelerator Board package. MONITOR CABLE (NOT PROVIDED) GRAPHIC

ACCELERATOR BOARD INSTALL (PLUG) INTO PCI BUS SLOT ANALOG OUTPUT DIGITAL OUTPUT DIGITAL FLAT PANEL CABLE (NOT PROVIDED)

SERIAL PORT INPUT PS/2 PORT INPUT COMPUTER AUDIO OUTPUT R L COMPUTER AUDIO CABLE (NOT PROVIDED) COMPUTER INPUT 1

AUDIO INPUT 1 R L USB 1 AUDIO 1 CONTROL PORT 1 (DIGITAL) ANALOG DIGITAL 1 - NI

R L (MONO) R E T U P M O C MOUSE CABLE FOR 2 -

PS/2 PORT (PROVIDED) USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) RGB H V NI R ET UP M OC

MOUSE CABLE FOR SERIAL PORT (PROVIDED) SERIAL PORT CABLE (NOT PROVIDED) CONTROL PORT OUTPUT 1 R/C JACK SERIAL PORT SERIAL PORT OUTPUT AUDIO OUT R L COMPUTER ANALOG RGB T U O R ET UP M OC

AUDIO AUDIO CABLE (NOT PROVIDED) AUDIO OUTPUT

INPUT SPEAKER

L R Amp. OUT L R Speaker (L) Speaker (R)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 16 CONNECTING THE PROJECTOR CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER COMPUTER VGA CABLE

SERIAL PORT INPUT PS/2 PORT INPUT COMPUTER OUTPUT (DB15-PIN TYPE) COMPUTER AUDIO OUTPUT R L (PROVIDED) AUDIO CABLE (NOT PROVIDED)

COMPUTER AUDIO INPUT 1 R L COMPUTER INPUT 1 (ANALOG) 1 -

USB 1 AUDIO 1 CONTROL PORT 1 ANALOG DIGITAL NI

R MOUSE CABLE FOR PS/2 PORT (PROVIDED) L (MONO) R ET UP M O C 2-

CONTROL PORT USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) RGB H V NI R ET UP M OC

OUTPUT 1 MOUSE CABLE FOR SERIAL PORT (PROVIDED) R/C JACK SERIAL PORT SERIAL PORT AUDIO OUT R L ANALOG RGB COMPUTER T U O R ET UP M OC

SERIAL PORT CABLE AUDIO OUTPUT OUTPUT (NOT PROVIDED) AUDIO CABLE (NOT PROVIDED) SPEAKER OUT

AUDIO INPUT R L Amp. Speaker (L) Speaker (R) L R

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 17 CONNECTING THE PROJECTOR CONNECTING AN IBM-COMPATIBLE LAPTOP COMPUTER (DIGITAL INPUT CONNECTION) NOTE: This connection need optionally sold Graphic Accelerator PC card. For this information, contact to your authorized dealer. Before using with digital connection, install (Plug in) Graphic Accelerator PC card into card bus slot of the computer and set up the computer following instructions in the Graphic Accelerator PC

COMPUTER card package. GRAPHIC ACCELERATOR

SERIAL PORT INPUT PS/2 PORT INPUT INSTALL (PLUG) INTO PC CARD BUS SLOT COMPUTER AUDIO OUTPUT PC CARD R L ANALOG OUTPUT DIGITAL OUTPUT AUDIO CABLE (NOT PROVIDED) DIGITAL FLAT PANEL CABLE (PROVIDED)

COMPUTER AUDIO INPUT 1 R L 1 - COMPUTER USB 1 AUDIO 1 CONTROL PORT 1 ANALOG DIGITAL NI

MOUSE CABLE FOR PS/2 PORT (PROVIDED) R L (MONO) R ET UP M O C 2- INPUT 1 (DIGITAL)

CONTROL PORT USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) RGB H V NI R ET UP M OC

OUTPUT 1 MOUSE CABLE FOR SERIAL PORT (PROVIDED) R/C JACK SERIAL PORT SERIAL PORT AUDIO OUT R L ANALOG RGB COMPUTER T U O R ET UP M OC

AUDIO OUTPUT SERIAL PORT CABLE OUTPUT (NOT PROVIDED) AUDIO CABLE (NOT PROVIDED) SPEAKER

AUDIO INPUT R L Amp. OUT L R Speaker (L) Speaker (R)

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 18 CONNECTING THE PROJECTOR CONNECTING A MACINTOSH DESKTOP COMPUTER COMPUTER MONITOR CABLE

(NOT PROVIDED) COMPUTER OUTPUT (BNC TYPE x 5) BNC CABLE x 5 (NOT PROVIDED)

VGA/MAC ADAPTER (PROVIDED)

ADB PORT ADB PORT COMPUTER OUTPUT COMPUTER AUDIO OUTPUT N O R L 6 5 4 3 2 1 VGA CABLE (PROVIDED) INPUT INPUT AUDIO CABLE (NOT PROVIDED) COMPUTER AUDIO OUTPUT1 or 2 R L COMPUTER INPUT 1 (ANALOG) 1 -

USB 1 AUDIO 1 CONTROL PORT 1 ANALOG DIGITAL NI

R L (MONO) R ET UP M O C 2-

MOUSE CABLE FOR ADB PORT (PROVIDED) USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) N RGB H V I R E T U P M O C COMPUTER INPUT 2 SERIAL PORT CABLE (NOT PROVIDED) CONTROL PORT OUTPUT 1 or 2 R/C JACK SERIAL PORT SERIAL PORT OUTPUT AUDIO OUT R L COMPUTER ANALOG RGB T U O R ET UP M OC MONITOR OUTPUT

AUDIO INPUT AUDIO CABLE (NOT PROVIDED) AUDIO OUTPUT Speaker (L) Speaker (R) Amp. R L SPEAKER OUT L

R Set the dip switches as shown in the table below depending on the RESOLUTION MODE that you want to use before you turn on the projector and computer. VGA/MAC ADAPTER SW1 ~ SW6

RESOLUTION MODE 13" MODE (640 x 480) 16" MODE (832 x 624) 19" MODE (1024 x 768) 21" MODE (1152 x 870) SW1 ON OFF OFF ON SW2 ON ON ON ON SW3 OFF OFF ON ON SW4 OFF ON OFF ON SW5 OFF OFF OFF OFF SW6 OFF OFF OFF OFF ON OFF ON 1 2 3 4 5 6

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 19 CONNECTING THE PROJECTOR CONNECTING A MACINTOSH POWERBOOK COMPUTER

COMPUTER NOTE: The Macintosh PowerBook requires the use of the PowerBook Video Adapter shipped with the PowerBook. VGA/MAC ADAPTER (PROVIDED)

ADB PORT INPUT ADB PORT INPUT COMPUTER OUTPUT COMPUTER AUDIO OUTPUT N O R L 6 5 4 3 2 1 VGA CABLE (PROVIDED) COMPUTER

AUDIO CABLE (NOT PROVIDED) COMPUTER AUDIO INPUT 1 R L INPUT 1 (ANALOG) 1 -

USB 1 AUDIO 1 CONTROL PORT 1 ANALOG DIGITAL NI

R L (MONO) R ET UP M O C 2-

MOUSE CABLE FOR ADB PORT (PROVIDED) USB 2 CONTROL PORT 2 AUDIO 2 R L (MONO) N RGB H V I R E T U P M O C

CONTROL PORT OUTPUT 1 SERIAL PORT CABLE R/C JACK SERIAL PORT SERIAL PORT AUDIO OUT R L ANALOG RGB COMPUTER AUDIO OUTPUT T U O R ET UP M OC

(NOT PROVIDED) AUDIO INPUT AUDIO CABLE (NOT PROVIDED) SPEAKER OUTPUT R L Amp. OUT L R Speaker (L) Speaker (R)

Set the dip switches as shown in the table below depending on the RESOLUTION MODE that you want to use before you turn on the projector and computer. VGA/MAC ADAPTER SW1 ~ SW6

RESOLUTION MODE 13" MODE (640 x 480) 16" MODE (832 x 624) 19" MODE (1024 x 768) 21" MODE (1152 x 870) SW1 ON OFF OFF ON SW2 ON ON ON ON SW3 OFF OFF ON ON SW4 OFF ON OFF ON SW5 OFF OFF OFF OFF SW6 OFF OFF OFF OFF ON OFF ON 1 2 3 4 5 6

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector and peripheral equipment on before the computer is switched on. 20 CONNECTING THE PROJECTOR CONNECTING THE VIDEO EQUIPMENT CONNECTING TO THE VIDEO INPUT JACKS (1 and 2) BNC TYPE x 3 Connect to the video outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Connect video output from AV equipment to these jacks using the BNC cables. The video input can be connected 3 types of signals; “COMPOSITE VIDEO", "Y/C SEPARATE VIDEO" and COMPONENT VIDEO {Y, Cb (B-Y), Cr (R-Y)}. Set VIDEO SOURCE of each video input (VIDEO IN-1 or VIDEO IN-2) to input video matter. (Refer to "VIDEO SOURCE SELECT" operation on page 44). CONNECTING S-VHS VIDEO INPUT JACKS (1 and 2) The Video input includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack. CONNECTING TO THE AUDIO INPUT JACKS (1 and 2) Connect to the audio outputs of a VCR, video disc player, DVD player, video camera, satellite TV tuner or other AV equipment. Use RCA type audio cable for connection. ● If the audio signal from the AV equipment is stereo, be sure to connect the right and left channels to the respective right and left audio input jacks. ● If the external audio signal is monaural, connect it to the left jack. CONNECTING TO THE VIDEO MONITOR OUTPUT JACKS (BNC TYPE x 3) These jacks will contain the video information of the selected program source being viewed on the screen (Video 1 or Video 2). If you have selected program source Video 2 the video signal connected to the Video 2 video input jack will be available at the video monitor output jacks. If you select program source "Computer 1" or "Computer 2, the video signal connected to the Video 1 video input jack will be available at the video monitor output jacks. Use BNC cable for connection. CONNECTING TO THE S-VHS VIDEO MONITOR OUTPUT JACK The Video monitor output includes an extra video input jack marked S-VIDEO to allow connection to an S-VHS format VCR that has separate Y/C video signals. The S-VIDEO jack has priority over the VIDEO jack. CONNECTING TO THE AUDIO MONITOR OUTPUT JACKS These jacks will contain the audio information of the selected program source being viewed on the screen (Video 1 or Video 2). If you have selected program source Video 2 the audio signal connected to the Video 2 audio input jack will be available at the audio monitor output jacks. If you select program source "Computer 1" or "Computer 2", the audio signal connected to the Video 1 audio input jack will be available at the audio monitor output jacks. Use RCA type audio cable for connection. ● If the audio input of the audio equipment is stereo, be sure to connect the right and left channels to the respective right and left jacks. ● If the audio input of the audio equipment is monaural, connect it to the left jack. 21

CONNECTING THE PROJECTOR CONNECTING THE VIDEO EQUIPMENT VIDEO EQUIPMENT DVD Player Video Disc PlayerSatellite Video Camera

Video Cassette Recorder TV Tuner

VIDEO OUTPUT (BNC) Y OUTPUT (BNC) C OUTPUT (BNC) Cb (B-Y) OUTPUT (BNC) 1 Cr (R-Y) OUTPUT (BNC) S-VIDEO OUTPUT AUDIO OUTPUT

- N I OE DI V 2 - N I OE DI V T U O R O TI NO M VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO VIDEO/Y C/Cb(B-Y) Cr(R-Y) S-VIDEO AUDIO R L (MONO) AUDIO R L (MONO) AUDIO R L (MONO)

VIDEO INPUT (BNC) Y INPUT (BNC) C INPUT (BNC) Cb (B-Y) INPUT (BNC) MONITOR Cr (R-Y) INPUT (BNC) S-VIDEO INPUT AUDIO INPUT SPEAKERS AUDIO AMP.

NOTE: When connecting the cable, the power cords of both the projector and the external equipment should be disconnected from AC outlet. Turn the projector on before the peripheral equipment is switched on. 22 BEFORE OPERATION CONTROLS AND INDICATORS FRONT INDICATORS TOP CONTROLS

FRONT INDICATORS 1 2 3 4 LAMP READY WARNING

LAMP REPLACE TEMP.

TOP CONTROLS 5 10 11 6 7 9 8 VOLUME ZOOM FOCUS LENS SHIFT ON-OFF MODE MENU AUTO IMAGE NORMAL SELECT 14

12 13 15

23 BEFORE OPERATION 1 LAMP REPLACEMENT INDICATOR Light is orange when the Lamp life draws to an end. 2 TEMPERATURE WARNING INDICATOR Flashes red when internal projector temperature is too high. 3 READY INDICATOR Light is green when projector lamp is ready to be turned on. 4 LAMP POWER INDICATOR Light is dim when the projector is on. Light is brightened when the projector is in stand-by mode. 5 VOLUME BUTTONS Used to adjust volume. 6 ZOOM BUTTONS Used to operate power zoom lens. 7 FOCUS BUTTONS Used to operate power focus system. 8 LENS SHIFT BUTTONS Used to operate power lens shift. 9 POWER ON/OFF BUTTON Used to turn the projector on or off. 10 MODE BUTTON Used to select source. (Computer 1, Computer 2, Video 1 or Video 2 Input) 11 AUTO IMAGE BUTTON Used to operate the AUTO IMAGE adjustment. 12 MENU BUTTON This button will activate the MENU operation. Use this button, the POINT UP/DOWN/LEFT/RIGHT buttons and the SELECT button to make adjustments to the projector's setting in MENU operation. 13 NORMAL BUTTON Used to reset to normal picture adjustment preset by factory. 14 POINT UP/DOWN/LEFT/RIGHT BUTTONS To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing these buttons (UP, DOWN, LEFT or RIGHT). 15 SELECT BUTTON This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS. 24 BEFORE OPERATION OPERATION OF THE REMOTE CONTROL WIRELESS REMOTE CONTROL UNIT This remote control unit is not only able to operate the projector but also usable as a wireless mouse for a PC. One pointing pad and two click buttons are used for wireless mouse operation. Wireless mouse is usable when PC mouse pointer is displayed on the screen. When the menu or indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used. NOTE: To use the unit as a PC wireless mouse, connect the projector to the PC with the attached cable. Signals from the projector are transmitted to the PC, enabling the remote control unit of the projector to be used as a PC wireless mouse. (Refer to "CONNECTING THE PROJECTOR" in pages 15 to 20 for the connection.) LASER LIGHT WINDOW LASER POINTER button This remote control emits a laser beam light as the Laser Pointer from the Laser Light Window. When the LASER POINTER button is pressed, laser light goes on: when the button is released, light goes off. Laser light is emitted with the RED light indicating that the laser beam is being emitted. The laser emitted is a class laser; therefore, do not look into the laser light window or shine the laser beam on yourself or other people. The three marks to the right are the caution labels for the laser beam. CAUTION-use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

5 7

FRONT SIDE 2

1 4 9 12 COMPUTER VOLUME MUTE AUTO IMAGE VIDEO ZOOM FOCUS LENS SHIFT MENU ON-OFF P-TIMER NOFREEZE/ SHOW CURSOR NORMAL 3 6 8 11 14 19

10 13

16 LASER POINTER button LASER15 D.ZOOM 18 17

25 BASIC OPERATION 1 COMPUTER SELECT BUTTON Used to select computer mode. (Computer 1 or Computer 2 Input) 2 VIDEO SELECT BUTTON Used to select video mode. (Video 1 or Video 2 Input) 3 POWER ON/OFF BUTTON Used to turn the projector on or off. 4 VOLUME BUTTONS Used to adjust volume. 5 ZOOM BUTTON Used to select power zoom lens adjust. 6 P-TIMER BUTTON Used to operate the P-TIMER function. 7 FOCUS BUTTON Used to select focus adjust. 8 FREEZE/NO SHOW BUTTON Used to freeze on-screen image or change the screen into black image. 9 SOUND MUTE BUTTON Used to mute sound. 10 LENS SHIFT BUTTON Used to select power lens shift. 11 CURSOR BUTTON Used to display CURSOR on the screen. 12 AUTO IMAGE BUTTON Used to operate the AUTO IMAGE adjustment. 13 MENU BUTTON This button will activate the MENU operation. Use this button, the POINT UP/DOWN/LEFT/RIGHT button and the SELECT (REAR CLICK) button to make adjustments to the projector's setting in MENU operation. 14 NORMAL BUTTON Use to reset to normal picture adjustment preset by factory. 15 POINTING PAD (POINT UP/DOWN/LEFT/RIGHT BUTTON) When in use as a remote for the projector To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing the pad upward, downward, leftward or rightward. Used to operate power zoom lens, power focus system or power lens shift by pressing the pad either upward or downward. When in use as a wireless mouse Used to move the pointer. The pointer is moved according to the direction you are pressing. 16 LASER BUTTON When this button is pressed, laser light goes on; when the button is released, light goes off. 17 FRONT CLICK BUTTON When in use as a remote for the projector Used to compress the image in D.ZOOM mode. When in use as a wireless mouse This button has the same function as the right button in a PC mouse. 18 DIGITAL ZOOM BUTTON Used to select digital zoom function. 19 SELECT (REAR CLICK) BUTTON When in use as a remote for the projector. This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS. When in use as a wireless mouse This button has the same function as the left button in a PC mouse. 26 BEFORE OPERATION Remote Control Battery Installation 1Remove the battery compartment lid. 2 Slide the batteries into the compartment. 3 Replace the compartment lid. Note : For correct polarity (+ and - terminal), be sure the battery terminals are in contact with the pins in the compartment. Using the Remote Control Unit Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4' (5m) and 60° front and rear of the projector.

16.4' (5 m) 60° 60° To insure safe operation, please observe the following precautions : ● Use (2) AA type alkaline batteries. ● Change two batteries at the same time. ● Do not use a new battery with a used battery. ● Avoid contact with water. ● Do not drop the remote control unit. ● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries. 16.4' (5 m)

27 BEFORE OPERATION WIRELESS/WIRED REMOTE CONTROL UNIT

1 WIRED REMOTE JACK When using the wired remote control, connect the remote 1 cable to this jack. 2 COMPUTER SELECT BUTTON 3 Used to select computer mode. 9 (Computer 1 or Computer 2 Input) 3 COMPUTER VIDEO 6 ON-OFF

VIDEO SELECT BUTTON Used to select video mode. (Video 1 or Video 2 Input) 2 4 VOLUME ZOOM FOCUS

4 POWER ON/OFF BUTTON Used to turn projector on or off. 5 7 8 MUTE LENS SHIFT P-TIMER 10 5 VOLUME BUTTONS Used to adjust volume. 12 11 14 AUTO IMAGE MENU FREEZE/

6 7 8 9 10 11 12 ZOOM BUTTONS Used to operate power zoom lens. FOCUS BUTTONS Used to operate power focus system. SOUND MUTE BUTTON Used to mute sound. LENS SHIFT BUTTONS Used to operate power lens shift. P-TIMER BUTTON Used to operate the P-TIMER function. AUTO IMAGE BUTTON Used to operate the AUTO IMAGE adjustment. MENU BUTTON This button will activate the MENU operation. 13 16 SELECT D.ZOOM NO SHOW NORMAL 15 1714

Use this button, the POINT UP/DOWN/LEFT/RIGHT buttons and the SELECT button to make adjustments to the projector's setting in MENU operation. 13 POINT UP/DOWN/LEFT/RIGHT BUTTONS To select an item on the MENU that you want to adjust. To select an item, move the arrow by pressing these buttons (UP, DOWN, LEFT or RIGHT). 14 FREEZE/NO SHOW BUTTON Used to freeze on-screen image or change the screen into black image. 15 SELECT BUTTON This button has different functions depending on when used. This button is used to execute the item selected, to increase or decrease the values in certain items such as CONTRAST or BRIGHTNESS. 16 DIGITAL ZOOM BUTTON Use to select digital zoom function. 17 NORMAL BUTTON Used to reset to normal picture adjustment preset by factory. 28 BEFORE OPERATION Remote Control Battery Installation 1Remove the battery compartment lid. 2 Slide the batteries into the compartment. 3 Replace the compartment lid. Note : For correct polarity (+ and - terminal), be sure the battery terminals are in contact with the pins in the compartment. OPEN OPEN The remote control unit can be used as wireless or wired remote control. Using the Remote Control Unit (wireless) Point the remote control toward the projector (Receiver window) whenever pressing the buttons. Maximum operating range for the remote control is about 16.4' (5m) and 60° front and rear of the projector. 16.4' 16.4' (5 m) (5 m) 60° 60° Using the Remote Control Unit (wired)

Connect a remote control cable to R/C jacks located on the wireless/wired remote control unit and the side of the projector. To insure safe operation, please observe the following precautions : ● Use (2) AA type alkaline batteries. ● Change two batteries at the same time. ● Do not use a new battery with a used battery. ● Avoid contact with water. ● Do not drop the remote control unit. ● If batteries have leaked on the remote control, carefully wipe the case clean and load new batteries. R/C JACK SERIAL PORT WIRED REMOTE CABLE

29 BEFORE OPERATION OPERATING ON-SCREEN MENU HOW TO OPERATE ON-SCREEN MENU You can control and adjust this projector through the ON-SCREEN MENU. Refer to the following pages to operate each adjustment in the ON-SCREEN MENU.

1 MOVING THE POINTER Move the pointer (see the NOTE below) by pressing POINT button(s) on the TOP CONTROL or on the REMOTE CONTROL. 2 SELECT THE ITEM Select the item by pressing SELECT (REAR CLICK) button. WIRELESS REMOTE CONTROL POINT BUTTON Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. NOTE : Pointer is the icon on the ON-SCREEN Menu to select the item. See the figures on the section "FLOW OF ON-SCREEN MENU" below. TOP CONTROL POINT BUTTONS SELECT BUTTON Used to select the item. WIRELESS/WIRED REMOTE CONTROL

MENU Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. SELECT BUTTON MENU FREEZE/ NO SHOW SELECT SELECT BUTTONUsed to select the item.

Used to select the item. NORMAL SELECT D.ZOOM NORMAL

Display ON-SCREEN MENU POINT BUTTONS Used to move the Pointer UP/ DOWN/ RIGHT/ LEFT. FLOW OF ON-SCREEN MENU MENU BAR

1 Press MENU button to display the ON-SCREEN MENU (MENU BAR). The red frame is the POINTER. POINTER (red frame) ITEM ICON

Select the Item SELECT

2 Move the POINTER (red frame) to the ITEM ICON that you want to select by pressing POINT RIGHT / LEFT buttons. 3 Select the ITEM by pressing SELECT (REAR CLICK) button. The dialog box of the ITEM appears. BUTTON POINTER (red frame)

Control and adjust through ON-SCREEN MENU

4 Move the POINTER downward by pressing POINT DOWN button. (The shape of the POINTER becomes an arrow.) 5 Move the POINTER to the ITEM that you want to adjust and adjust the ITEM by pressing SELECT (REAR CLICK) button. Refer to the following pages for details of respective adjustments. POINT DOWN BUTTON MENU POINTER

30 BEFORE OPERATION MENU BAR MENU BAR IN COMPUTER MODE Press MENU BUTTON while in Computer mode.

MODE MENU Used to select the Computer input mode. (Refer to P36) AUTO IMAGE MENU Used to adjust Fine sync, Total dots, and Picture Position automatically. (Refer to P41) PC ADJUST MENU Used to adjust the parameters to match with the input signal format. (Refer to P38, 39) SETTING MENU Used to set the Display Menu and reset Lamp Replacement Monitor Timer. (Refer to P48, 49) LANGUAGE MENU Used to select the language used in the Menu. (Refer to P49) SYSTEM MENU Used to select a computer system. (Refer to P36) IMAGE MENU Used to adjust the computer image. [Fine sync / Total dots / White Balance / Contrast / Brightness / Sharpness] (Refer to P40) POSITION MENU Used to adjust the position of the image. (Refer to P42) SCREEN MENU Used to adjust the size of the image. (Refer to P43) SOUND MENU Used to adjust or mute the Volume. (Refer to P35)

MENU BAR IN VIDEO MODE Press MENU BUTTON while in Video mode. IMAGE MENU

MODE MENU Used to select the Video input. (Refer to P44) Used to adjust the picture image. [Color / Tint / White Balance / Contrast / Brightness/ Sharpness (Refer to P46) Same function as the Computer Mode.

SYSTEM MENU Used to select a color system of the selected video source. (Refer to P45) VIDEO SOURCE MENU Used to select a video source among [(Video), (Y,C) and (Y, Cb, Cr)]. (Refer to P44) SCREEN MENU Used to set the size of the image either Regular or Wide. (Refer to P47)

31 BASIC OPERATION TURNING ON/OFF THE PROJECTOR TO TURN ON THE PROJECTOR Connect the projector to a source (Computer, VCR, Video Camera, Video Disc Player, etc.) using the appropriate terminals on the side of the projector (See "CONNECTING THE PROJECTOR" section on pages 13-22). Connect the projector's AC power cord into a wall outlet and turn the MAIN ON/OFF switch (located on the side of the projector) to the ON position. The LAMP POWER indicator will light RED, the READY indicator will light GREEN. Press the POWER ON/OFF button on the remote control unit or on the projector to ON. The LAMP POWER indicator light will dim and the cooling fans will operate. The wait display appears on the screen and the count-down starts (30-29-28-...1). The signal from the source appears after 30 seconds. 30 TO TURN OFF THE PROJECTOR Press the POWER ON/OFF button on the remote control unit or on the projector. The "Power off ?'' appears on the screen. Press again the POWER ON/OFF button to turn OFF the projector. The LAMP POWER indicator will light bright and READY indicator will turn off. The cooling fans will operate for 90 seconds after the projector is turned off. (During this "cooling down" period, the projector cannot be turned on.) The READY indicator will light green again and the projector may be turned on by pressing the POWER ON/OFF button. To power down completely, turn the MAIN ON/OFF switch (located on the side of the projector) to the OFF position. TO MAINTAIN THE LIFE OF THE LAMP, ONCE YOU TURN THE PROJECTOR ON, WAIT AT LEAST 5 MINUTES BEFORE TURNING IT OFF. When the Power Management function is ON, the Projector detects the signal interruption and turns the Projection Lamp off automatically. Refer to “Power Management” on page 48. When the TEMPERATURE WARNING indicator flashes red, the projector is automatically turned off. Wait at least 5 minutes before turning the projector on again. When the TEMPERATURE WARNING indicator continues to flash, follow procedures below: 1. Turn the MAIN ON / OFF SWITCH to OFF and disconnect the AC power cord from the AC outlet. 2. Check the air filters for dust accumulation. 3. Clean the Air Filter. (See "AIR FILTER CARE AND CLEANING" section on page 51.) 4. Turn the Projector on again. If the TEMPERATURE WARNING indicator should still continue to flash, contact the sales dealer where you purchased this projector or service center. NOTE: The Cooling Fan may work for cooling while the projector is turned off. When the Cooling Fan is working, TEMPERATURE WARNING INDICATOR flashes red. 32 BASIC OPERATION ADJUSTING THE IMAGE ZOOM ADJUSTMENT Use Top control and Wireless/Wired remote control unit. Press the ZOOM (▲) or (▼) button to obtain your desired picture size. For a larger picture, press (▲) and for a smaller picture, press (▼). Use Wireless remote control unit. Press the ZOOM button and press POINT UP/DOWN button(s) to obtain your desired picture size. The Zoom display will be displayed on the screen for a few seconds. For a larger picture, press (UP) and for a smaller picture, press (DOWN). FOCUS ADJUSTMENT Use Top control and Wireless/Wired remote control unit. Press the FOCUS (▲) or (▼) button for a sharper, crisper picture. Use Wireless remote control unit. Press the FOCUS button and press POINT UP/DOWN button(s) to obtain a sharper, crisper picture. The Focus display will be displayed on the screen for a few seconds. LENS SHIFT FUNCTION Use Top control and Wireless/Wired remote control unit. Press the LENS SHIFT (▲) or (▼) button to obtain your desired screen position. Use Wireless remote control unit. Press the LENS SHIFT button and press POINT UP/DOWN button(s) to obtain your desired screen position. The Lens shift display will be displayed on the screen for a few seconds. DIGITAL ZOOM FUNCTION Press the D. ZOOM button on the wireless remote control unit. The "D.zoom" and the magnifying-glass icon is displayed to indicate Digital zoom mode. Digital

zoom mode can be adjust the image size or pan the image. To expand the image size, press SELECT (REAR CLICK) button. The image is magnified by degrees (Expand function). To compress the image size, press FRONT CLICK button. The size of image is reduced by degrees (Compress function). To pan the image, press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) button(s). The image move to the direction indicated (Panning function) See the page 43 for more detail. NORMAL PICTURE FUNCTION The normal picture image level is factory preset on the projector and can be restored anytime by pressing the NORMAL button on the projector or on the remote control unit. The "Normal" display will be displayed on the screen for a few seconds. D. zoom

33 BASIC OPERATION FREEZE PICTURE FUNCTION Press the FREEZE/NO SHOW button on the remote control unit, and the picture will remain on-screen. This function is cancelled when the FREEZE/NO SHOW button is pressed again or any other button is pressed. NOTE: Your computer or video equipment is not affected by this function, and will continue to run. NO SHOW FUNCTION Press the FREEZE/NO SHOW button (on the remote control unit) is twice. The screen will change into black image and the "No show" is displayed on the screen for a few seconds. This function is cancelled when the FREEZE/NO SHOW button is pressed again or any other function button is pressed. P-TIMER FUNCTION Press the P-TIMER button on the remote control unit. The timer display "00:00" appears on the screen and the timer starts to count the time (00:00 to 59:59). Press again the P-TIMER button to stop the timer. Then press the P-TIMER button to cancel the P-TIMER function. AUTO IMAGE ADGUSTMENT Press the AUTO IMAGE button on the projector or on the remote control unit. The item(s) indicated "ON" in the AUTO IMAGE ADJUSTMENT are adjusted automatically. If all the items in AUTO IMAGE ADJUSTMENT are "OFF", AUTO IMAGE SETTING display appears. If you wish to operate the AUTO IMAGE ADJUSTMENT, perform the steps 1 - 3 of "AUTO IMAGE ADJUSTMENT" section on page 41. CURSOR FUNCTION Press the CURSOR button on the wireless remote control unit. The CURSOR is displayed on the screen. Press POINT UP/DOWN/LEFT/RIGHT (POINTING PAD) button(s) to control CURSOR. The CURSOR is moved according to the direction you are pressing. Press CURSOR button again, and CURSOR disappears. 34

SOUND ADJUSTMENT DIRECT OPERATION Sound Volume Adjustment Press the VOLUME (+/–) button(s) on the Top Control or on the Remote Control Unit to adjust the volume. The Volume dialog box appears on the screen for a few seconds. (+) button to increase the volume, and (–) button decreasing. Sound Mute Setting Press the MUTE button on the Remote Control Unit to cut off the sound. To restore the sound to its previous level, press the MUTE button again or press Volume (+/–) button(s). BASIC OPERATION Indicates the roughly level of the volume. Press the MUTE button to set the Mute function On or Off. MENU OPERATION 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SOUND and press the SELECT (REAR CLICK) button. Another dialog box SOUND ADJUST Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to select by pressing the POINT UP/DOWN buttons. Volume The display disappears after 4 seconds. Indicate the roughly level of the item. Move the arrow to ▲ Move the arrow to ▲ or ▼ of "Volume" by pressing the POINT UP/ DOWN buttons. To increase the volume, point the arrow to ▲ and then press the SELECT (REAR CLICK) button. To decrease the volume point the arrow to ▼ and then press the SELECT (REAR CLICK) button. Treble To adjust the Treble sound, point the arrow to ▲ or ▼ of "Treble" and then press the SELECT (REAR CLICK) button. Bass To adjust the Bass sound, point the arrow to ▲ or ▼ of "Bass" and then press the SELECT (REAR CLICK) button. Built-in SP. To disconnect the built-in speaker, point the arrow to Built-in SP. and then press the SELECT (REAR CLICK) button. The Built-in SP. display is changed Off from On and Internal speaker is disconnected. Mute To cut off the audio sound, point the arrow to "Mute" and then press the SELECT (REAR CLICK) button. The Mute display is changed On from Off and the sound is cut off. To restore the sound to its previous volume level, set the Mute to Off. or ▼ and press the SELECT (REAR CLICK) button. Move the arrow to the item and then press the SELECT (REAR CLICK) button. Close the Sound Menu.

35 COMPUTER MODE SELECTING COMPUTER MODE

DIRECT OPERATION Press the MODE button on the projector or the COMPUTER button on the remote control unit to select Computer 1, Computer 2 Input. The "Computer 1", or "Computer 2" display will appear on the screen for a few seconds. MENU OPERATION MODE button Computer 1 Computer 2 Video 1 Video 2 COMPUTER button Computer 1 Computer 2

1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT (REAR CLICK) button. Another dialog box COMPUTER MODE Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the mode either Computer 1 or Computer 2, and then press the SELECT (REAR CLICK) button.

CURRENT MODE DISPLAY When selecting the Computer Mode, the Current Mode display appears to show the information of the computer being selected. Providing the information of the computer detected by the projector.

SELECTING COMPUTER SYSTEM AUTOMATIC MULTI-SCAN SYSTEM This projector automatically tunes to most different types of computers based on VGA, SVGA, XGA or SXGA (refer to “COMPATIBLE COMPUTER SPECIFICATION” on page 37). When selecting Computer, this projector automatically tunes to the incoming signal and projects the proper image without any

special settings. (Setting of the Computer System may be required when connecting some computers.) Note : The projector may display one of the following messages. SYSTEM BOX Display the SYSTEM being selected.

Go to PC adj. No signal The projector cannot discriminate or detect the input signal from the computer. Adjust and set the computer system manually. (Refer to page 38.) There is no signal input from the computer. Make sure the connection of the computer and the projector is set correctly. (Refer to TROUBLESHOOTING on page 53.) The system being selected. The systems on this dialog box can be selected. If the incoming signal is digital, the "D-VGA", "D-SVGA", "D-XGA" or "D-SXGA" display appears. SELECT COMPUTER SYSTEM MANUALLY To set the Computer system manually, select the mode on the ON-SCREEN MENU. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT (REAR CLICK) button. Another dialog box COMPUTER SYSTEM Menu will appear. When this mark is displayed as black, more computer system modes will be available. Move the arrow to this mark and then press the SELECT (REAR CLICK) button, and the other modes will be displayed. Close the SYSTEM Menu.

2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the system that you want to set, and then press SELECT (REAR CLICK) button. 36 COMPUTER MODE COMPATIBLE COMPUTER SPECIFICATIONS

ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz) ON-SCREEN DISPLAY RESOLUTION H-Freq. (kHz) V-Freq. (Hz)

VGA1 VGA2 VGA3 VGA4 VGA5 VGA6 VGA7 MAC LC13 MAC13 SVGA1 SVGA2 SVGA3 SVGA4 SVGA5 SVGA6 SVGA7 SVGA8 SVGA9 SVGA10 SVGA11 MAC16 XGA1 XGA2 XGA3 XGA4 XGA5 XGA6 XGA7 XGA8 XGA9 XGA10 XGA11 XGA12 XGA13 640 x 480 720 x 400 640 x 400 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 640 x 480 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 800 x 600 832 x 624 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 1024 x 768 31.47 31.47 31.47 37.86 37.86 37.50 43.269 34.97 35.00 35.156 37.88 46.875 53.674 48.08 37.90 34.50 38.00 38.60 32.70 38.00 49.72 48.36 68.677 60.023 56.47 60.31 48.50 44.00 63.48 36.00 62.04 61.00 35.522 46.90 59.88 70.09 70.09 74.38 72.81 75.00 85.00 66.60 66.67 56.25 60.32 75.00 85.06 72.19 61.03 55.38 60.51 60.31 51.09 60.51 74.55 60.00 84.997 75.03 70.07 74.92 60.02 54.58 79.35 87.17 (Interlace) 77.07 75.70 86.96 (Interlace) 58.20 XGA14 XGA15 MAC19 SXGA1 SXGA2 SXGA3 SXGA4 SXGA5 SXGA6 SXGA7 SXGA8 SXGA9 SXGA10 SXGA11 SXGA12 SXGA13 SXGA14 SXGA15 SXGA16 SXGA17 SXGA18 SXGA19 SXGA20 MAC21 MAC MAC RGB RGB HDTV720p HDTV1035i HDTV1080i 1024 x 768 1024 x 768 1024 x 768 1152 x 864 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 960 1152 x 900 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1280 x 1024 1152 x 900 1280 x 1024 1280 x 1024 1280 x 1024 1152 x 870 1280 x 960 1280 x 1024 768 x 576 640 x 480 1280 x 720 1920 x 1035 1920 x 1080 47.00 58.03 60.24 64.20 62.50 63.90 63.34 63.74 71.69 81.13 63.98 79.976 60.00 61.20 71.40 50.00 50.00 63.37 76.97 61.85 46.43 63.79 91.146 68.68 75.00 80.00 15.625 15.734 45.00 33.75 33.75 58.30 72.00 75.08 70.40 58.60 60.00 59.98 60.01 67.19 76.107 60.02 75.025 60.00 65.20 75.60 86.00 (Interlace) 94.00 (Interlace) 60.01 72.00 66.00 86.70 (Interlace) 60.18 85.024 75.06 75.08 75.08 50.00 (Interlace) 60.00 (Interlace) 60.00 60.00 (Interlace) 60.00 (Interlace)

Specifications are subject to change without notice. NOTE: Basically this projector can accept the signal from all computers with the above mentioned V, H-Frequency and less than 220 MHz of Dot Clock. 37 COMPUTER MODE PC ADJUSTMENT This Projector can automatically tune to the display signals from most personal computers currently distributed. However, some computers employ special signal formats which are different from the standard ones and may not be tuned by the Multi-Scan system of this projector. If this happens, the projector cannot reproduce a proper image and the image may be recognized as a flickering picture, a non-synchronized picture, a non-centered picture or a skewed picture. This projector has a PC ADJUSTMENT function to enable you to precisely adjust several parameters to match with those special signal formats. This projector has 8 independent memory areas to memorize those parameters manually adjusted. This enables you to recall the setting for a specific computer whenever you use it. Note : This PC ADJUSTMENT function will be skipped when the incoming signal is digital.

1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT RIGHT/LEFT button to select PC ADJUST and press the SELECT (REAR CLICK) button. Another dialog box “Where to reserve” Menu will appear. 2 In this dialog box, you can store the parameter into the area from “Mode 1” to “Mode 8.” When memorizing the new computer parameter, select the Mode with the message “Free” by pressing the POINT UP/DOWN button and the SELECT (REAR CLICK) button. To change the parameters of the Mode previously set, select the Mode with “Stored.” 3 When the Mode is selected, Parameter adjustment dialog box appears. Move the arrow to the item that you want to change by pressing the POINT UP/DOWN button, and adjust each item by pressing the SELECT (REAR CLICK) button to match with your computer. 4 Move the arrow to “Stored” and press the SELECT (REAR CLICK) button. The parameter is memorized in the selected Mode. 5 To activate the Mode manually adjusted in this PC ADJUSTMENT Menu, select the Mode at the SYSTEM SELECT Menu. (Refer to page 36.) This Mode has parameters being stored. The Vacant Mode. Manual set Computer Mode (1 to 8). Close the PC ADJUSTMENT Menu. Move the arrow to ▲ or ▼ and press SELECT (REAR CLICK) button.

38

Total lines The number of the total vertical lines. Adjust the number to match the image of your personal computer. Total dots The number of the total dots in one horizontal period. Adjust the number to match the image of your computer. Horizontal / Vertical Adjustment of the horizontal or vertical picture position. When the image is not centered on the screen, adjust each of those items. Clamp Adjustment of the clamp level. When the image has a dark bar(s), try this adjustment. Fine sync COMPUTER MODE Press the SELECT (REAR

Adjust the picture as necessary to eliminate flicker from the display. Display area Adjustment of the area displayed with this projector. Select the resolution at the Display area dialog box, or adjust the number at the column of “H” or “V” to match the resolution of the image. Horizontal Scale / Vertical Scale Adjustment of the horizontal height or vertical width of the image. NOTE : The Display area, the Horiz. scale and the Vert. scale cannot be adjusted when “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P24 and 25). Each of the keys operates as follow. CLICK) button at this column to adjust “Clamp,” “Fine sync,” “Display area,” “Horiz. scale” or “Vert. scale” . 640 X 480 720 X 400 800 X 600 1024 X 768 1152 X 864 1280 X 1024

Reset Recalls the parameter data that was previously adjusted.

Mode free Clears the parameter data previously set. Stored Stores the parameters in the memory. Quit Closes the PC ADJUST Menu. Point the arrow at the Display area and press the SELECT (REAR CLICK) button. The Display area dialog box appears.

39 COMPUTER MODE PICTURE IMAGE ADJUSTMENTS 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT (REAR CLICK) button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT (REAR CLICK) button. Fine sync

Adjust the picture as necessary to eliminate flicker from the display. (From 0 to 127.) Total dots The number of the total dots in one horizontal period. Adjust the number to match your PC image. White balance (Red / Green / Blue) Move the arrow to the color that you want to adjust. Point to ▼ to lighten the color and select ▲ to deepen the color. (From 0 to 63.) Contrast Move the arrow to ▲ or ▼ and press SELECT (REAR CLICK) button. Close the PICTURE IMAGE ADJUSTMENT Menu. Point to ▼ to decrease contrast, and select ▲ to increase contrast. (From 0 to 63.) Brightness Point to ▼ to adjust the image darker, and select ▲ to adjust brighter. (From 0 to 63.) Sharpness Point to ▼ to soften the image, and select ▲ to sharpen the image. (From 0 to 31.) Each of the keys operates as follow. Reset Recalls the data previously adjusted. Stored Stores the adjusted data in the memory. Quit Closes the PICTURE IMAGE ADJUSTMENT Menu. NOTE : This menu cannot be operated when the incoming signal is digital or “RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P36 and 37).

40 COMPUTER MODE NORMAL FUNCTION The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The “Normal” display will be displayed on the screen for a few seconds. Normal AUTO IMAGE ADJUSTMENT The Auto Image adjustment is provided to automatically adjust Fine sync., Total dots, and Picture Position for most computers. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select AUTO IMAGE and press the SELECT (REAR CLICK) button. Another dialog box AUTO IMAGE Menu will appear. 2 Move the arrow to an item that you want to adjust by pressing the POINT UP/DOWN button. Change the setting On or Off by pressing the SELECT (REAR CLICK) button. Fine sync

Adjust the picture as necessary to eliminate flicker from the display. This item can be adjusted manually. (Refer to page 40.) Total dots The number of the total dots in one horizontal period. This item can be adjusted manually. (Refer to page 40.) Position Adjustment of the position of the image. This item can be adjusted manually. (Refer to page 42.) Starts the adjustment on the item set to "On". Terminates the PICTURE IMAGE ADJUSTMENT Menu. Move the arrow to the item and then press the SELECT (REAR CLICK) button.

3 Move the arrow to “Go!” and press the SELECT (REAR CLICK) button to start the Auto Image adjustment. This adjustment can be executed by pressing AUTO IMAGE button on the Projector or on the Remote Control Unit. Stored Stores the On/Off setting of each item. Go! Starts the Auto Image Adjustment. Quit Closes the AUTO IMAGE ADJUSTMENT Menu. NOTE : This menu cannot be operated when the incoming signal is digital or “RGB,” “HDTV720p,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P36 and 37). The Fine sync., Total dots, and Picture Position of some computers may not be fully adjusted with the Auto Image ADJUSTMENT. In that case, manual adjustment is required to make fine image. (Refer to page 40 to adjust "Fine sync." or "Total dots" and page 42 to adjust Picture Position.) 41 COMPUTER MODE PICTURE POSITION ADJUSTMENT The position of the image can be adjusted vertically and horizontally through PICTURE POSITION ADJUSTMENT. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select POSITION and press the SELECT (REAR CLICK) button. The PICTURE POSITION dialog box will appear.

2 Select the arrow to the direction (described as , , or ) that you want to adjust by pressing the POINT UP/DOWN/ LEFT/RIGHT buttons, and then press the SELECT (REAR CLICK) button. Each of the keys operates as follow. Reset Recalls the setting data previously set. Stored Stores the setting data in the memory. Quit Closes the PICTURE POSITION Menu. Select the arrow to the direction (described as , , or ),and then press the SELECT (REAR CLICK) button.

42 COMPUTER MODE PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size. 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT (REAR CLICK) button. Another dialog box PICTURE SCREEN Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT (REAR CLICK) button. True

To make the image into its original size, select True in the dialog box. When the original image size is larger than the screen size (1024 x 768), the image can be panned by pressing the POINT UP/DOWN/LEFT/RIGHT buttons. Digital Zoom NOTE Move the arrow to the function and press the SELECT (REAR CLICK) button. To adjust the image size or pan the image, select Digital zoom in the dialog box. The ON-SCREEN menu and SCREEN ADJUST menu disappears, and the magnifying glass icon and the message “D. Zoom” is displayed. This projector also enters Digital Zoom mode by pressing the Select (REAR CLICK) and FRONT CLICK buttons on the Wireless Remote Control Unit. Refer to the following for operation. Expand function To expand the image size, press the SELECT (REAR CLICK) button. The image is magnified by degrees. Compress function To compress the image size, press the FRONT CLICK button. The size of image is reduced by degrees. Panning function To pan the image, press the POINT UP/DOWN/LEFT/RIGHT buttons. Panning function can work only when the image is larger than the screen size. To cancel Digital Zoom mode, press any button except SELECT (REAR CLICK), FRONT CLICK, or POINT button. To adjust the image to 1024 x 768, press NORMAL button. ● The True and the Digital Zoom cannot be operated when “RGB,” “HDTV1035i” or “HDTV1080i” is selected on the SYSTEM MENU (P36 and 37). ● This projector cannot display any resolution higher than 1280 X 1024. If your computer’s screen resolution is higher than 1280 X 1024, reset the resolution to the lower before connecting the projector. ● The image data in other than 1024 x 768 is modified to fit the screen size in the initial mode. ● The normal "Panning Operation" may not function properly if the computer system prepared with the "PC Adjust" is used.

43

VIDEO MODE SELECTING VIDEO MODE

DIRECT OPERATION Press the MODE button on the projector or the VIDEO button on the remote control unit to select Video 1, Video 2 Input. The "Video 1", or "Video 2" display will appear on the screen for a few seconds. MODE button Computer 1 Computer 2 Video 1 VIDEO button Video 1 Video 2

Video 2 MENU OPERATION 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select Computer and press the SELECT (REAR CLICK) button. Another dialog box VIDEO MODE Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the mode either Video 1 or Video 2, and then press the SELECT (REAR CLICK) button. SELECTING VIDEO SOURCE

This projector automatically detects the signal from the VIDEO INPUT JACK(s) or the S-VIDEO INPUT JACK. When those jacks are connected at the same time, select the type of Video source in VIDEO SOURCE Menu. This box indicates the Video source being selected.

1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select VIDEO SOURCE and press the SELECT (REAR CLICK) button. Another dialog box VIDEO SOURCE Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the source that you want to select, and then press the SELECT (REAR CLICK) button.

Video When connect the composite video output from the video equipment to the VIDEO/Y jack, select "Video" in VIDEO SOURCE Menu.

Y, C When connect the separate Y/C video output from the video equipment to the VIDEO/Y and C jacks, select "Y,C" in VIDEO SOURCE Menu. Y, Cb, Cr When connect the component video output from the video equipment to the VIDEO/Y, C/Cb (B-Y) and Cr (R Y) jacks, select "Y, Cb, Cr" in VIDEO SOURCE Menu. 44 VIDEO MODE SELECTING COLOR SYSTEM 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SYSTEM and press the SELECT (REAR CLICK) button. Another dialog box VIDEO SYSTEM Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to "Auto", and then press the SELECT (REAR CLICK) button. VIDEO SIGNAL FROM VIDEO JACK OR S-VIDEO JACK This box indicates the system being selected. Auto

The projector automatically detects the incoming Video system, and adjusts itself to optimize its performance. When the Video System is PAL-M or PAL-N, select the system manually. PAL / SECAM / NTSC / NTSC4.43 / PAL-M / PAL-N If the projector cannot reproduce the proper video image, it is necessary to select a specific broadcast signal format among PAL, SECAM, NTSC, NTSC 4.43, PAL-M, and PAL-N. Move the arrow to the Mode and press the SELECT (REAR CLICK) button.

45 VIDEO MODE PICTURE IMAGE ADJUSTMENT 1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select IMAGE and press the SELECT (REAR CLICK) button. Another dialog box PICTURE IMAGE ADJUSTMENT Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the function that you want to select and then press SELECT (REAR CLICK) button. Move the arrow to ▲ or ▼ and press

Color Point to ▼ button to lighten the image, and select ▲ to deepen the image. (From 0 to 63.) Tint Point to ▼ button to increase purple, and select ▲ to increase green. (From 0 to 63.) White balance (Red / Green / Blue) Move the arrow to the color that you want to adjust. Point to ▼ to lighten the color and select ▲ to deepen the color. (From 0 to 63.) Contrast Point to ▼ button to decrease contrast, and select ▲ to increase contrast. (From 0 to 63.) Brightness Point to ▼ button to darken the image, and select ▲ to brighten the image. (From 0 to 63.) Sharpness Point to ▼ button to soften the image, and select ▲ to sharpen the image. (From 0 to 31.) Each of the keys operates as follow. Reset Recalls the data previously adjusted. Stored Stores the data in the memory. Quit Closes the PICTURE IMAGE ADJUSTMENT Menu. SELECT (REAR CLICK) button. Closes the PICTURE IMAGE ADJUSTMENT Menu.

46 VIDEO MODE NORMAL FUNCTION The normal picture level is preset on this projector at the factory and can be restored anytime you press the NORMAL button (located on the Top Control or on the Remote Control Unit). The "Normal" display will be displayed on the screen for a few seconds. Normal PICTURE SCREEN ADJUSTMENT This projector has a picture screen resize function, which enables you to display the desirable image size.

1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SCREEN and press the SELECT (REAR CLICK) button. Another dialog box PICTURE SCREEN ADJUSTMENT DISPLAY will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the screen size that you want to set, and then press the SELECT (REAR CLICK) button. Regular Move the pointer to the function and Normal Video Image size with 4 x 3 aspect ratio. Wide Resizes the image for wide screen size with 16 x 9 aspect ratio. press the SELECT (REAR CLICK) button.

47

SETTING SETTING MENU

1 Press the MENU button and the ON-SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT (REAR CLICK) button. Another dialog box SETTING Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the item that you want to set, and then press the SELECT (REAR CLICK) button to set it "On" or "Off" or press the POINT LEFT/RIGHT button to adjust the value. Blue back

When this function is “On,” this projector will produce a blue image instead of the video noise on the screen when the input source is unplugged or turned off. Display This function decides whether to display the On-Screen Displays. On ··· shows all the On-Screen Displays. Off ···· sets the On-Screen Displays disappeared except; ● ON SCREEN MENU ● “Power off?” message ● P-TIMER Reverse T/B When this function is “On,” the top / bottom reversed picture is provided to project the image from a ceiling mounted projector. Reverse L/R When this function is “On,” the left / right reversed picture is provided to project the image to a rear projection screen. Split wipe Turn this function “On” in the SETTING menu. The picture will change into next one by sliding black image side ways like drawing the black curtains when the input source is turned into another one. Power management This function turns the Projection Lamp off when the projector detects signal interruption and the projector is not used for a certain period in order to reduce power consumption and maintain the Lamp life. (This projector is shipped with this function ON.) Power Management function operates to turn the Projection Lamp off when the input signal is interrupted and the projector is not operated over 5 minutes. This function operates as follows; 1. When the signal is interrupted, “No signal” and the counting down (5 minutes) display appears. 2. When the Projection Lamp turned off, the READY indicator turns off. The Cooling Fans operate for 90 seconds after the Projection Lamp is turned off. (During this "Cooling Down" period, the Lamp cannot be turned on.) 3. When the Lamp has cooled down, the READY indicator flashes and the Lamp can be turned on again (Power Management mode). In this Power Management mode, the Projection Lamp is automatically turned on when the input signal connected or the projector is operated with any button on the Top Control or on the Remote Control. Set the Pointer to the item and press the SELECT (REAR CLICK) button. Reverse T/B function Reverse L/R function Time left until Lamp off.

48 SETTING USB This Projector is equipped with USB port for interactive operation between the projector and the computer. Set the mode following steps below. Wireless Mouse mode Select " " when controlling the computer with the Remote Control of this projector. Projector mode Select " " when controlling the projector with the computer. NOTE: Before you control the projector by computer, install USB driver (optionally sold parts) and set up the computer following instruction in the USB driver package. Contact your authorized dealer. Remote control This projector has two different remote transmit codes; the factory-set normal code (Mode 1) and the secondary code (Mode 2). This switching function prevents the remote control operation mixture (jam) when operating several projectors or video equipment together. When operating the projector in “Mode 2” both projector and Remote Control must be switched to “Mode 2”. To change the code of the projector; Set the Remote control in the SETTING menu to “Mode 2”. To change the code of the Remote Control; Press both the MENU and the NORMAL buttons on the Remote Control together for over 10 seconds. After changing the code, make sure the Remote Control operates properly. To return to the normal code (Mode 1), operate both projector and Remote Control in the ways above again. Lamp replacement monitor timer Be sure to reset the Lamp Replacement Monitor Timer when the Lamp Assembly is replaced. When the Lamp Replacement Monitor Timer is reset, the LAMP REPLACEMENT indicator stops lighting. 1 Turn the projector on, and press the MENU button and the ON SCREEN MENU will appear. Press the POINT LEFT/RIGHT buttons to select SETTING and press the SELECT (REAR CLICK) button. Another dialog box SETTING MENU will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to “Lamp age” and then press the SELECT (REAR CLICK) button. 3 Move the arrow to replaced lamp number and then press the SELECT (REAR CLICK) button. The message "Lamp replace monitor Reset?" is displayed. Select [Yes] to reset the Timer. 4 NOTE; Do not reset the Lamp Replacement Monitor Timer, except after the lamp is replaced. SELECTING LANGUAGE The language used in the ON-SCREEN MENU is selectable from among English, German, French, Italian, Spanish and Japanese.

1 Press the MENU button and the ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT buttons to select LANGUAGE and press the SELECT (REAR CLICK) button. Another dialog box LANGUAGE Menu will appear. 2 Press the POINT DOWN button and a red-arrow icon will appear. Move the arrow to the language that you want to set, and then press the SELECT (REAR CLICK) button. Move the Pointer to the language that you want to set, and then press the SELECT (REAR CLICK) button.

49 APPENDIX OPERATING WIRELESS MOUSE The Wireless Remote Control Unit is not only able to operate the projector but also usable as a wireless mouse for most Personal Computers. The POINT buttons and the two CLICK buttons are used for the wireless mouse operation. The wireless mouse is available only when PC mouse pointer is displayed on the screen. When the menu or the indicator of the projector is displayed on the screen instead of the PC mouse pointer, the wireless mouse cannot be used. INSTALLATION To use the Wireless Remote Control Unit as the Wireless Mouse for a Personal Computer, installation of the mouse driver (not supplied) is required. Make sure that the mouse driver is properly installed in your computer. And make sure that the mouse port of the computer connected to Control Port is activated.

1 Connect the mouse port of your computer to the Control Port of the projector with the Control Cable. (Refer to page 15 to 20 for connection.) 2 Turn the projector on first, and then turn on your computer. When the computer is switched on first, the Wireless Mouse may not work properly. Note : When the computer has no mouse port, connect the Serial Port of the computer to Control Port of the projector with the Control Cable for Serial Port.

USING USB TERMINAL USB Terminal can be also used as control port for wireless mouse operation. Connect the USB terminal of the computer to USB terminal of this projector with the USB cable (not supplied). In this operation, selecting Wireless Mouse Mode on SETTING Menu is required. (Refer to P49). OPERATING WIRELESS MOUSE When controlling the pointer of the computer, operate the Wireless Mouse with POINT button, SELECT (REAR CLICK) button, and FRONT CLICK button on the Wireless Remote Control Unit.

POINT button Used to move the pointer. The pointer is moved corresponding with the direction you are pressing. SELECT (REAR CLICK) button This button has the same function as the left button in a PC mouse. FRONT CLICK button This button has the same function as the right button in a PC mouse. Pressing this button does not affect any operation when in Menu mode. POINT button (Move the pointer)

SELECT (REAR LICK) button (left button of the mouse) FRONT CLICK button (right button of the mouse)

50 APPENDIX MAINTENANCE TEMPERATURE WARNING INDICATOR The TEMPERATURE WARNING INDICATOR flashes red when the internal temperature of the projector exceeds the normal temperature. Possible causes for the temperature warning may be : 1. Ventilation slots of the projector are blocked. In such an event, reposition the projector so that ventilation slots are not obstructed. 2. Air filter is clogged with dust particles. Remove dust from the air filter by following instructions in the Air Filter Care and Cleaning section below. 3. If temperature warning indicator remains on after performing the checks listed above, cooling fan/internal circuits may be malfunctioning. Request service from an authorized dealer or service station. TEMPERATURE WARNING INDICATOR AIR FILTER CARE AND CLEANING The removable air filter prevents dust from accumulating on the surface of the projection lens and projection mirror. Should the air filter become clogged with dust particles, it will reduce the cooling fan's effectiveness and may result in internal heat build up and reduce the life of the projector. To clean the air filter, follow the cleaning procedures below: 1. Turn the POWER ON/OFF button OFF. 2. Remove the air filter cover. 3. Remove the air filter and sponge from the filter cover. 4. Clean the air filter with a vacuum cleaner.

5. Replace the air filter and sponge. Make sure that air filter cover is fully inserted. Do not clean with water. Doing so may damage the air filter. Do not operate the projector with air filter removed. AIR FILTER COVER SPONGE AIR FILTER

RECOMMENDATION AIR FILTER COVER

TO ENJOY PICTURE IMAGE, USE THE PROJECTOR IN THE CLEAN ENVIRONMENT. USAGE IN THE CLEAN ENVIRONMENT IS RECOMMENDED. When used under the dusty or smoky conditions, dust may accumulate on the liquid crystal panel and lens inside it, and may resultantly be projected on the screen together with the picture. When the above symptoms are noticed contact the place where your authorized dealer or service station for the cleaning. 51 APPENDIX LAMP REPLACEMENT

WHEN THE PROJECTION LAMP OF THIS PROJECTOR DRAWS TO AN END, THE LAMP REPLACEMENT INDICATOR LIGHTS YELLOW AND THE WARNING MESSAGE "LAMP REPLACEMENT" APPEARS AS THE RIGHT FIGURE. WHEN THE WARNING MESSAGE IS DISPLAYED, THE PROJECTION LAMP SHOULD BE REPLACED. To terminate the warning message. Replace the Projection Lamp and reset the LAMP REPLACEMENT MONITOR TIMER (See "LAMP REPLACEMENT MONITOR TIMER" section on page 49.), and the warning message is terminated. To erase the warning message in a moment. To erase the warning message for a moment, move the arrow to "YES" by pressing the POINT UP/DOWN BUTTON(s) and then press the SELECT (REAR CLICK) BUTTON. This procedure is temporary measure, and the warning massage appears again when the projector is turned on next time. ● For continued safety, replace with a lamp assembly of the same type. LAMP REPLACEMENT INDICATOR LAMP REPLACEMENT

● Allow the projector to cool for at least 45 minutes before you open the lamp cover. The inside of the projector can become very hot. ● Do not drop the lamp module or touch the glass bulb ! The glass can shatter and cause injury. Follow these steps to replace the lamp assembly.

1. Turn off the projector and allow the projector to cool thoroughly. 2. Disconnect the AC cord from the projector. 3. Remove 2 screws with a screwdriver and remove the lamp cover. 4. Remove 2 screws with a screwdriver and pull out the lamp assembly by grasping the handle. 5. Replace the lamp assembly. 6. Tighten 4 screws to secure the lamp cover to the lamp assembly. 7. Connect the detachable AC cord to the projector. 8. Reset the lamp replacement monitor timer. (See "LAMP REPLACEMENT MONITOR TIMER" section on page 49.) NOTE: Do not reset the LAMP REPLACEMENT MONITOR TIMER, except after the lamp is replaced. ORDER REPLACEMENT LAMP LAMP COVER LAMP ASSEMBLY HANDLE

Replacement Lamp can be ordered through your dealer. When ordering the Lamp, give the following information to the dealer. ● Model No. of your projector : PLC-XF12N/PLC-XF12NL/PLC-XF12E/PLC-XF12EL/PLC-XF12B/PLC-XF12BL ● Replacement Lamp Type No. : POA-LMP26 (Service Parts No. 610 285 7450) 52 APPENDIX CLEANING THE PROJECTION LENS Follow these steps to clean the projection lens: 1. Apply a non-abrasive camera lens cleaner to a soft, dry cleaning cloth. Avoid using an excessive amount of cleaner. Abrasive cleaners, solvents or other harsh chemicals might scratch the lens. 2. Lightly wipe the cleaning cloth over the lens. 3. When you don't use the projector, replace the lens cover. TROUBLESHOOTING Before calling your dealer or service station for assistance, check the matters below once again. 1. Make sure you have connected the projector to your equipment as described in section "CONNECTING THE PROJECTOR" on pages 11 ~ 22. 2. Check cable connections. Verify that all computer, video and power cords are properly connected. 3. Verify that power is switched on. 4. If the projector still does not display an image, re-start the computer. 5. If the image still does not display, unplug the projector from the computer and check the computer monitor's display. The problem may be with your graphics controller rather than with the projector. (When you reconnect the projector, remember to turn the computer and monitor off before you power up the projector. Power the equipment back up in order of: Projector and computer) 6. If the problem still exists, check the following chart.

Problem: No power. Image is out of focus. Try these Solutions: ● Plug the projector into an AC outlet. ● Turn the MAIN ON/OFF switch to ON. ● Press the POWER ON/OFF switch to ON. ● Be sure the READY INDICATOR light is ON. ● Wait 90 seconds after the projector is turned OFF before turning the projector back on. NOTE: After pressing the POWER ON/OFF button to OFF. The projector functions as indicated. 1. The LAMP POWER indicator will light and the READY indicator will turn off. 2. After 90 seconds, the READY indicator will light green again and the projector may be turned on by pressing the POWER ON/OFF button. ● Check temperature warning indicator. If the indicator flashes red, the projector cannot be turned on. (See "BASIC OPERATION" section on page 32). ● Check the projection lamp. ● Replace the lamp cover. (Check the interlock switch inside of the lamp cover.) ● Adjust the focus. ● Make sure the projection screen is at least 4.9' (1.5 m) from the projector. ● Check the projection lens to see if it needs cleaning. NOTE: Moving the projector from a cool temperature location to a warm temperature location may result in moisture condensation on the lens. In such an event, leave the projector OFF and wait until condensation disappears.

53

APPENDIX Problem: Picture is T/B inverted. Try these Solutions: Check Reverse T/B feature. (See "SETTING" section on pages 48 ~ 49). Check Reverse L/R feature.

(See "SETTING" section on pages 48 ~ 49). Picture is L/R Reversed.

Some displays are not seen during the operation. No sound. Remote control unit doesn't work. Wireless mouse function does not work. SERVICE Check Display feature. (See "SETTING" section on pages 48 ~ 49). ● Check audio cable connection from audio input source. ● Adjust audio source. ● Press the VOLUME (+) button. ● Press the MUTE button. ● Check the batteries. ● Make sure nothing is blocking between the remote control sensor and remote control unit. ● Make sure you are not too far from the projector when using the remote control unit. {Maximum operate range 16.4 ' (5 m)}. ● Check the transmitted signal mode from the remote control unit. (See "SETTING" section on pages 48 ~ 49). ● Check the cable connection between the projector and the computer. ● Check the mouse setting on your computer. ● Turn on the projector before you turn on the computer. WARNING: High voltages are used to operate this projector. Do not attempt to open the cabinet. You can often correct operating problems yourself. If the projector fails to work properly, see "TROUBLESHOOTING" section on page 53, 54. To correct the failure, try the "Solutions". If after following all operating instructions, you find that service is necessary, contact the Sanyo Service Station or the store where you purchased the unit. Give the model number and explain the difficulty. We will advise you how to obtain service.

This symbol on the nameplate means the product is Listed by Underwriters Laboratories Inc. It is designed and manufactured to meet rigid U.L. safety standards against risk of fire, casualty and electrical hazards. The CE Mark is a Directive conformity mark of the European Community (EC). 54

Projector Type Dimensions (W x H x D) Net Weight LCD Panel System Number of Pixels APPENDIX TECHNICAL SPECIFICATIONS Multi-media Projector 15.4" (390 mm) x 9.6" (245 mm) x 23" (585 mm) 39.2 Ibs (17.8 kg) 1.8" TFT Active Matrix type x 3 panels 2,359,296 {786,432 (1,024 x 768) x 3} Color System Scanning Frequency Projection Image Size (Diagonal) Horizontal Resolution Projection Lens Motorized Lens Shift Throw Distance Projection Lamp AV Input Jacks Video Monitor Output Jack Audio Monitor Output Jacks Computer Input 1 Jack Computer Input 2 Jack Computer Audio Input Jack Computer Output Jack Computer Audio Output Jack Other Jack Built-in Speaker Image Elevation Adjustment Voltage and Power Consumption Operating Temperature Storage Temperature Remote Control Transmitters 6 color system (PAL, SECAM, NTSC, NTSC4.43, PAL-M and PAL-N) H-sync. 15 ~ 100 KHz, V-sync. 50 ~ 120 Hz Adjustable from 40" to 600" 800 TV lines F2.0 ~ 2.3 lens with f=75.7 mm ~ 97.5 mm Motor zoom and focus ± 760 mm on 100" screen 4.9' (1.5 m) ~ 80.7' (24.6 m) 440 watt type BNC Type {Video/Y, C/Cb (B-Y), Cr (R-Y)} x 2 sets, RCA Type (Audio R and L) x 2 sets and DIN 4 pin (S-Video) x 2 sets BNC Type {Video/Y, C/Cb (B-Y),Cr (R-Y)} x 1 set and DIN 4 pin (S-Video) x 1 set RCA Type (R and L) x 1 set MDR 20-pin Terminal (Digital), HDB 15-pin Terminal (Analog), Multi-pole 12-pin (Control port) and USB port BNC Type (R, G, B, H and V), Multi-pole 12-pin (Control port) and USB port RCA Type (R and L) x 2 sets HDB 15-pin Terminal RCA Type (R and L) x 1 set Wired Remote Jack and Serial port (DB 9) INT. SP. Stereo (R and L), 3 watt RMS (T.H.D.10%) Up to 4° AC 100 ~ 120 V (7.8A Max. Ampere), 50/60 Hz (The U.S.A and Canada) AC 200 ~ 240 V (3.6A Max. Ampere), 50/60 Hz (Continental Europe and The U.K.) 41°F ~ 95°F (5°C ~ 35°C) 14°F ~ 140°F (–10°C ~ 60°C) Wireless Remote Control with Laser Beam (Class Laser) Max. Output 1mW/Wave Length 660 ± 20nm, batteries (2) AA type. Wireless/Wired Remote Control, batteries (2) AA type.

● The specifications are subject to change without notice. 55

Printed in Japan Part No. 610 289 9580 (1AA6P1P2649-- PE6AB) SANYO Electric Co., Ltd


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply