Free English SANUS VST15 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SANUS VST15 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is the weight capacity for the SANUS VST15?
The weight capacity for the SANUS VST15 is DO NOT EXCEED: 22.6 kg (50 lb), which includes the TV and any accessories.
What is the tilt range for the SANUS VST15?
The tilt range for the SANUS VST15 is ±12°.
What precautions should be taken regarding personal injury and property damage when using the SANUS VST15?
Avoid potential personal injuries and property damage by following these precautions:
Do not use this product for any purpose not explicitly specified by manufacturer.
The wall must be capable of supporting five times the weight of the monitor and mount combined.
This product is designed for use in wood frame walls only!
If you do not understand these instructions, or have doubts about the safety of the installation, assembly or use of this product, contact Customer Service or call a qualified contractor.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
What are the required tools for installing the SANUS VST15?
The required tools are:
12mm (7/16 in.) tool
3mm (1/8 in.) tool
Drill
What parts and hardware are supplied with the SANUS VST15?
The supplied parts and hardware for the SANUS VST15 are:
| Part | Quantity |
| [01] | x 1 |
| [02] | x 1 |
| 1/4 x 21/2 in. [03] | x 2 |
| M4 x 12mm [04] | x 4 |
| M4 [05] | x 4 |
What warning should be observed before starting assembly of the SANUS VST15?
WARNING: This product contains small items that could be a choking hazard if swallowed. Before starting assembly, verify all parts are included and undamaged. If any parts are missing or damaged, do not return the damaged item to your dealer; contact manufacturer Customer Service. Never use damaged parts!
How do I mount the TV bracket [01] onto the TV for the SANUS VST15?
Step 1: Mount TV Bracket. Ensure the bracket is level on the back of the TV. Standard configuration is shown.
NOTE: If the hole pattern on your TV is 75mm x 75mm the washer [05] will not be used. If you require additional space for cables, recesses, or protrusions, contact Customer Service.
How do I locate a stud for mounting the wall plate [02] of the SANUS VST15?
Step 2-1 Locate stud. Verify the center of the stud using an awl, a thin nail, or an edge to edge stud finder.
CAUTION: Avoid potential personal injuries and property damage!
Any material covering the wall must not exceed 16 mm (5/8 in.).
Minimum wood stud size: common 51 x 102 mm (2 x 4 in.) (nominal 38 x 89 mm (11/2 x 31/2 in.)).
How do I mark the wall for the SANUS VST15 wall plate [02]?
Step 2-2 Mark the wall. Level the wall plate [02] and mark the hole locations.
What are the requirements for drilling pilot holes when installing the SANUS VST15 wall plate [02]?
Step 2-3 Drill pilot holes. CAUTION: Avoid potential injuries or property damage! Pilot holes MUST be drilled to a depth of 631/2 mm (21/2 in.), using a 3 mm (1/8 in.) diameter drill bit.
How should the lag bolts [03] be tightened when securing the wall plate [02] for the SANUS VST15?
Step 2-4 Tighten lag bolts. CAUTION: Avoid potential injuries or property damage! Improper use could reduce the holding power of the lag bolt. To avoid potential injuries or property damage:
DO NOT over-tighten the lag bolts [03].
Tighten the lag bolts [03] only until they are pulled firmly against the wall plate [02].
What is required for hanging the TV onto the wall plate [02] when installing the SANUS VST15?
Step 3 Hang TV onto the Wall Plate. HEAVY! You will need assistance with this step.
How is the TV secured to the wall plate [02] for the SANUS VST15?
Step 4 Secure TV to Wall Plate. This step involves securing the TV bracket [01] to the wall plate [02], typically using a locking mechanism shown in the diagram.
How do I adjust the up/down tilt tension on the SANUS VST15?
Step 5 Adjust Up / Down Tilt Tension. Adjust the tension screw on the tilt mechanism to achieve the desired tension for ± 12° tilt.
CLICK HERE TO DOWNLOAD SANUS VST15 (01) PDF DOCUMENT