Free English RESPEKTA CH 99090 W A (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD RESPEKTA CH 99090 W A (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the accessories included with the RESPEKTA CH 99090 W A cooker hood according to the accessory list?
The accessory list for the RESPEKTA CH 99090 W A cooker hood includes the following items:
| Item | Picture | Number |
|---|---|---|
| Lower chimney a) and upper chimney b) | (Diagram showing outer and inner chimney parts) | 1 |
| Upper chimney bracket | (Diagram showing the bracket) | 1 |
| Lower chimney stabilizer- and fixing bar | (Diagram showing the bar) | 1 |
| Wall plug $\\phi$8 | (Diagram showing a wall plug) | 8 |
| Screw ST4\\times40mm (2 for upper chimney mounting bracket, 2 for lower chimney mounting plate) | (Diagram showing a screw) | 4 |
| Screw ST4\\times30mm (2 pcs for hood hanging, 2 pcs for hood locking) | (Diagram showing a screw) | 4 |
| ST4*8 screw (Upper- and lower Chimney fixing) | (Diagram showing a screw) | 6 |
| V-Flap | (Diagram showing the V-Flap) | 1 |
| Air exhaust pipe | (Diagram showing a flexible hose) | 1 |
| Ribbon-8\\times550mm. | (Diagram showing a ribbon/cable tie) | 1 |
How should the V-Flap be mounted on the RESPEKTA CH 99090 W A cooker hood if it is not factory-mounted?
If the valve flaps are not factory-mounted on the RESPEKTA CH 99090 W A cooker hood, follow these steps:
Step 1. First install half part 1 in connection nozzle B10.
Step 2. Pins 3 must be in upwards position.
Step 3. Insert the axle 4 into the holes 5 on the nozzle B10.
Step 4. Repeat all operations for mounting the half part 2.
What is the initial step before mounting the RESPEKTA CH 99090 W A cooker hood for recirculation mode?
Before beginning the mounting of the RESPEKTA CH 99090 W A cooker hood for recirculation mode, ensure the power supply is secure. This must be set up by a specialist. Also, before installing the hood, insert the V-Flaps as described.
What are the steps for mounting the RESPEKTA CH 99090 W A cooker hood for recirculation mode?
The steps for mounting the RESPEKTA CH 99090 W A cooker hood for recirculation mode are as follows:
Step 1. Using a pencil, draw a horizontal line at the height on the wall on which the hood bottom edge should lie. It is best to use a water level. Attention! Observe minimum distance according to chapter 11.1 of the operating instructions.
Step 2. Hold the supplied drill template with the bottom edge on the drawn pencil line against the wall and mark the four drill holes.
Step 3. Drill a 30mm deep hole in the wall with an 8mm masonry drill at the 4 pencil marks. For safety, check the diameter of the plugs with a caliper gauge.
Step 4. Place one plug into each of the 4 holes.
Step 5. Screw one ST4 \\times 30mm screw each into the two dowels for the hood suspension. Attention! The screw heads must protrude 3 – 5 mm from the dowels so that the hood can be hung on them. (Readjust after the hood has been hung up).
Step 6. Hang the hood with the two eyelets on its back by the two screws on the wall.
Step 7. Mount the stabilizer- and mounting plate at the top of the lower flue with two ST4 * 8mm screws.
Step 8. Place the lower chimney shaft on the hood.
Step 9. Firmly press the chimney shaft against the wall and mark with pencil the two drill holes through the holes in the chimney stabilize- and mounting plate.
Step 10. Remove the chimney from the hood.
Step 11. Drill two 40mm deep holes into the wall at the marked locations using an 8mm masonry drill.
Step 12. Push the upper (inner) chimney shaft from above into the lower (outer) chimney shaft.
Step 13. Place the nested chimneys on the hood.
Step 14. Pull the inner chimney shaft straight up to the ceiling and place one marking line on the sides of the shaft.
Step 15. Remove the chimneys from the hood.
Step 16. Hold the upper (inner) chimney mounting bracket at the top center of the ceiling between the drawn marks and mark the drilled holes with the two holes in the mounting bracket a pencil.
Step 17. Using an 8mm masonry drill, drill two 40mm deep holes at the pencil markers and place two plugs.
Step 18. Fix the inner chimney mounting bracket to the wall with two ST4 \\times 40mm screws at the top of the ceiling.
Step 19. Place the two nested chimneys on the hood.
Step 20. Slide the inner chimney shaft all the way down.
Step 21. Attach the lower chimney stabilize- and mounting plate to the wall with two ST4 x 40mm screws.
Step 22. Fix the lower chimney shaft with two ST4 * 8mm screws on the sides of the hood.
Step 23. Pull the upper (inner) chimney shaft all the way up and secure it to the mounting bracket with two ST4 * 8mm screws.
Step 24. Secure the RESPEKTA CH 99090 W A hood with two ST4 \\times 30mm screws through the 2 hood fixing eyelets .
Step 25. Mount the carbon filters on the sides of the motor. (See user’s manual chapter “Using the carbon filters”).
What preparations and steps are necessary for mounting the RESPEKTA CH 99090 W A cooker hood for exhaust air operation?
For mounting the RESPEKTA CH 99090 W A cooker hood for exhaust air operation, you must observe chapter 11. “Installation” of the user’s manual. The wall duct must be dimensioned for a 150 mm exhaust hose (Drill hole about 155mm).
To mount the hood in exhaust air mode, mount it as described in the chapter “Mounting the hood for recirculation mode:”, but without mounting the carbon filters.
Proceed as follows during assembly:
Step 1. Remove the outer and inner chimney.
Step 2. Mount the exhaust hose. (Fig. k)
Step 3. Replace the outer and inner chimney.
Note: For the final assembly of the RESPEKTA CH 99090 W A hood in exhaust air operation, you need an exhaust grille with a 150mm socket (a) for the connection of the exhaust air hose. This is not included in the delivery.
CLICK HERE TO DOWNLOAD RESPEKTA CH 99090 W A (01) PDF DOCUMENT