RESPEKTA CH 99090 SA (01) PDF Document

Prior to carrying out cleaning or maintenance work, the power supply to the extractor hood must be interrupted by:

• Pulling out the appliance connector plug or tripping the house installation circuit breaker or fully unscrewing the screw type fuse from the house installation.

There is a fire risk if cleaning is not carried out in accordance with the instructions.

Flambieren (flaming) under the RESPEKTA CH 99090 SA is not permitted due to the fire risk, as the rising flame can set fire to grease deposited in the filter.

Frying or cooking with oils and fats under the RESPEKTA CH 99090 SA is only to take place under constant surveillance due to the fire risk. The risk of self-ignition increases with oils which have been used repeatedly.

When the range hood and appliances supplied with energy other than electricity are simultaneously in operation, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

If the RESPEKTA CH 99090 SA is used in circulation air mode, it is absolutely safe to simultaneously operate a room air-dependent fire.

When using the RESPEKTA CH 99090 SA in exhaust air mode and operating with chimney-dependent firing methods (e.g. coal oven), care must be taken for an adequate supply of fresh air in the installation location. This should always be discussed with the responsible chimney-sweeping specialist.

Do not use cleaning agents containing alcohol to clean appliances with a matt black finish, as these can lead to discolouring.

For daily cleaning of the outer parts of the RESPEKTA CH 99090 SA, use a soft cloth moistened with alcohol or a mild liquid cleaner. Never use an abrasive cleaner.

For cleaning stainless steel surfaces, a commercially available non-abrasive stainless steel cleaning agent should be used.

Treatment with a stainless steel preservative is recommended to prevent surfaces from becoming quickly re-soiled. Apply the agent all over and economically using a soft cloth.

Never use stainless steel cleaning agents in the vicinity of the control elements.

The metal grease filters do not have to be replaced when they are over-saturated but should be washed once a month by hand or in a dishwasher (60°). Do not use a corrosive rinsing agent.

Allow the filter to dry thoroughly and carefully replace it in the extractor hood.

Avoid using alkaline dishwasher cleaning agents (pH value over 7).

When cleaning metal grease filters, take care not to damage the mesh. Frequent cleaning or the use of aggressive cleaning agents can cause colour changes to the metal surface. These do not affect the filter function and are not grounds for complaint.

Change paper grease filters monthly.

Change paper grease filters with alarm every two months or when the colour of the surface becomes visible through the mesh openings. This filter is coloured on one side; after fitting, this colouring must not be visible through the mesh openings.

Foam grease filters must be soaked once a month in warm soapy water for 1 to 2 hours. Do not wring out.

Repeat where required and replace the filter by a new item after a maximum of 5-6 washes.

Traditional carbon filters (normally round in shape) can be neither washed nor regenerated.

The charcoal filters have to be replaced regularly, at least every 3 months or earlier, depending on the cooking habits.

Washable and regeneratable carbon filters (normally square in shape) are to be washed once a month in a dishwasher, using a standard rinsing agent and with the intensive rinsing program (at the highest temperature).

Washable and regeneratable carbon filters absorb kitchen odours for a maximum of 3 years when cleaned monthly. The filter should then be replaced by a new item.

Washable and regeneratable carbon filters should be washed separately to avoid food residue deposits which can later cause unpleasant odours.

After washing, the washable and regeneratable carbon filter must be reactivated by drying the cleaned filter in an oven for 10 minutes at 100°C.

The grease filter must always be in place when operating the RESPEKTA CH 99090 SA, otherwise grease vapour can become deposited in the hood and the exhaust air system.

Grease filters obstructed by dirt particles seriously impair the appliance function.

The grease filters on your appliance are to be cleaned or replaced at regular intervals. Filters saturated with grease can quickly catch fire and also distribute unpleasant odours.

Possible causes and solutions are:

Possible causes and solutions are:

Possible causes and solutions are:

Possible causes and solutions are:

Possible causes and solutions are:

Possible causes and solutions are:

To select the required power level, use the “B” and “C” buttons.

Tap the “C” key. The motor runs at the lowest power level.

Tap the “C” key again to go to the second power level.

Press the “C” key again to go to the third power level. At the respective power level, the display shows 1, 2 or 3.

To reduce the power level, press the “B” key repeatedly until the desired power level is shown on the display “A”.

To switch off the cooker hood, tap the ON / OFF button “F”.

With the timer button “E” you can set a running time of up to 5 minutes (with the device switched on). The motor and lights switch off automatically after the set time. The timer can be set again or switched off before the set time expires.

Attention! If a new power level is set after activating the timer, the timer will automatically be deactivated.

The “D” key (Light ON / OFF) can be operated when the cover is closed.

After opening the front cover by tapping the ON / OFF key “F”, the light is on when the motor is running at low speed.

Tap the ON / OFF key “F”. The front cover of the cooker hood is opened. The backlight of this key is on, the motor is running at low speed and the light is on. The backlighting of the “B”, “C” and “D” keys lights up.

Touch the ON / OFF “F” key again. The front cover of the hood is closed. The background lighting of all buttons goes out, the cooker hood is switched off and returns to standby mode.

There are 2 sensors on the control panel (refer to O on the picture).

To operate the Cooker hood in the gesture sensor mode follow the instruction here below.

1. Wave your hand once from left sensor to the right sensor within 8 cm from the front of the sensors. The front cover of the cooker hood will be opened. The cooker hood will start to work at low speed and the LED display will show “1”. The lights will light on. The backlights of the following keys will be on:

Gesture operation for speed increase:

• Wave your hand from left to right again, the cooker hood works at mid speed and the LED display will show “2”.
• Wave your hand in the same direction as above for another time, the cooker hood works at high speed and the LED display will show “3”.
• Wave your hand in the same way again when the hood works at the highest speed, the hood will work at the same speed.

2. When you wave your hand from right to left once, the cooker hood will shift to a lower speed. If the hood works at high speed, wave your hand from right to left, the hood will switch to mid speed. The backlights of the following keys will be on:

Gesture operation for speed decrease:

• When the hood works at mid speed, wave your hand from right to left, the hood will switch to low speed, and the LED display will show the current speed level.
• If continuously reducing to no speed, the backlights will be off and all the function operation of the hood will not be available. The hood will then enter in standby mode. The above steps can be operated repeatedly.

3. If without any operation for functional buttons in 10 minutes, the gesture sensor will enter sleeping mode. Re-awake gesture function requires manual operation of any function buttons. The gesture function can be operated only when it has been activated.

Minimum distance from the lower edge of the hood body:

The diameter of the exhaust air pipeline should not be less than 120 mm because otherwise higher running noise or reduced extraction capacity can be expected.

If the exhaust air pipeline is horizontally routed, there must be a minimum gradient of 1 cm per metre or an inclination angle of 2°.

Otherwise condensation water could run into the extractor hood motor.

Check the following when the motor fails to function:

• Is the plug properly inserted in the socket?
• Is there a power supply failure?
• Has a fuse blown?

Check the following if the hood capacity is insufficient / operating noise has increased:

• Is the size of the exhaust air pipeline sufficient?
• Is the exhaust air duct blocked?
• The cross section of the air pipeline (from the hood to the wall box incl.) should be 120 mm. A smaller air pipeline cross-section can possibly impair the motor power.
• The air flow can be obstructed if the wall box is fitted with a fly mesh. If this is the case remove the fly mesh.
• If the cover plate of the wall box has fixed, very inclined louvres, you should remove the plate to check whether this solves the problem. Mount a cover plate with movable louvres in the wall box, as this will least obstruct the air flow.
• Is / are the filter(s) clean?
• Was / were the carbon filter(s) installed more than six months ago? Then this/these should be changed.
• Is the air taken from the kitchen being replaced by sufficient fresh air, so that no partial vacuum is being produced in the room?

Check the following if the lighting fails to function:

• Does the lamp need changing?
• Has the lamp been properly fitted and seated in the holder up to the stop?
• Is the fuse blown or has the circuit breaker tripped out?

If the documentation of the cooker hood does not include an instruction for replacing LED lamps, the lamp must be replaced by the customer service for safety reasons.

When changing a lamp, make sure that the new lamp does not have a higher wattage than that of the original.

Operating the cooker hood in gesture sensor mode:

1. Wave your hand once from left sensor to the right sensor within 8 cm from the front of the sensors, the front cover of the cooker hood will be opened. The cooker hood will start to work at low speed and the LED display will show “1”. The lights will light on. The backlights of the following keys will be on:

Gesture operation for speed increase:

• Wave your hand from left to right again, the cooker hood works at mid speed and the LED display will show “2”.
• Wave your hand in the same direction as above for another time, the cooker hood works at high speed and the LED display will show “3”.
• Wave your hand in the same way again when the hood works at the highest speed, the hood will work at the same speed.

2. When wave your hand from right to left once, the cooker hood will shift to a lower speed. When the hood work at high speed, wave your hand from right to left, the hood will switch to mid speed. The backlights of the following keys will be on:

Gesture operation for speed decrease:

• When the hood work at mid speed, wave your hand from right to left, the hood will switch to low speed, and the LED display will show current speed level. If continuously reducing to no speed, the backlights will be off and all the function operation of the hood will not be available. The hood will then enter in standby mode. The above steps can be operated repeatedly.

3. If without any operation for functional buttons in 10 minutes, the gesture sensor will enter sleeping mode. Re-awake gesture function requires manual operation of any function buttons. The gesture function can be operated only when it has been activated.