RESPEKTA CH 99060 WA (01) PDF Document

When the RESPEKTA CH 99060 WA is operated in exhaust air mode simultaneously with fuel-burning appliances, the negative pressure in the room must not exceed 4 Pa (4 x 10-5 bar).

Keep small children away from the RESPEKTA CH 99060 WA.

Operation of the RESPEKTA CH 99060 WA by physically, sensorially, or mentally reduced persons is only permitted under the supervision of responsible adults.

The RESPEKTA CH 99060 WA is designed only for domestic use and must be used exclusively for that purpose.

Installation must be performed by qualified specialists.

The RESPEKTA CH 99060 WA and its filters must be cleaned regularly to ensure flawless function. Please observe the chapter “Cleaning and Care”.

Grease or oil-containing filters pose a significant fire hazard.

The exterior of the RESPEKTA CH 99060 WA may only be cleaned when it is switched off.

For interior cleaning of the RESPEKTA CH 99060 WA, it must be disconnected from the power supply.

Flambéing under the RESPEKTA CH 99060 WA is prohibited under any circumstances.

If the RESPEKTA CH 99060 WA malfunctions, the customer service must be notified. Never attempt to repair the RESPEKTA CH 99060 WA yourself.

Keep the room well ventilated when operating the RESPEKTA CH 99060 WA over a gas hob.

The exhaust air hose of the RESPEKTA CH 99060 WA must be routed into a separate exhaust duct to the outside. It must not be routed through any other shafts or chimneys.

Read the operating instructions / installation instructions thoroughly before mounting the RESPEKTA CH 99060 WA.

Check whether the technical data (V and Hz) on the type plate of the RESPEKTA CH 99060 WA matches that of your home installation. If they do not match, return the RESPEKTA CH 99060 WA to the point of sale. In case of any uncertainty regarding this, ask your electricity supplier.

Any warranty claim must be proven exclusively by the warranty card from your dealer and/or the purchase receipt.

Accessible parts of the RESPEKTA CH 99060 WA can become hot when cooking appliances are underneath.

The RESPEKTA CH 99060 WA is intended for domestic use.

The manufacturer is not liable for damage caused by improper use or maloperation.

Extractor hoods remove unpleasant odours and vapours and create a pleasant room atmosphere.

Particles of grease, steam and also moisture are absorbed by the grease filter.

A correctly dimensioned extractor hood creates a pleasant room climate without producing draughts and ensures a bearable air humidity of 40-60%.

Make sure no open fire is burning in the fireplace before you switch on the RESPEKTA CH 99060 WA or there may be a heavy smoke formation in your home. Toxic combustion gases can also be drawn from the chimney or flue, into living rooms. This can be lethally dangerous!

When using the RESPEKTA CH 99060 WA in exhaust air mode and operating with chimney-dependent firing methods (e.g. coal oven) care must be taken for an adequate supply of fresh air in the installation location. Always discuss this with your responsible chimney-sweeping specialist.

Do not flame under the RESPEKTA CH 99060 WA.

Flambéing under the RESPEKTA CH 99060 WA is prohibited due to the fire risk. The rising flame can set fire to grease deposited in the filter.

Due to the fire risk, frying or cooking with oils and fats under the RESPEKTA CH 99060 WA is only to take place under constant surveillance.

Attention! The risk of self-ignition increases with oils which have been used repeatedly used.

Other activities with an open flame are not permitted. These could damage the filter or other parts of the appliance or even start a fire.

There is a fire risk if cleaning is not carried out in accordance with the instructions.

Non-compliance with the maintenance and cleaning instructions can result in a fire hazard due to grease deposits.

Filters saturated with grease can quickly catch fire and also distribute unpleasant odours.

The grease filter must always be in place when operating the RESPEKTA CH 99060 WA, otherwise grease vapour can become deposited in the hood and the exhaust air system.

The grease filters on your appliance are to be cleaned or replaced at regular intervals.

Grease filters obstructed by dirt particles seriously impair the appliance function.

Grease filters must occasionally be changed. The following rules apply:

1. Change paper grease filters monthly.
2. Change paper grease filters with alarm every two months or when the colour of the surface becomes visible through the mesh openings. This filter is coloured on one side; after fitting, this colouring must not be visible through the mesh openings.
3. Foam grease filters must be soaked once a month in warm soapy water for 1 to 2 hours. Do not wring out; repeat where required and replace the filter by a new item after a maximum of 5-6 washes.
4. Metal grease filters do not have to be replaced when they are over-saturated but washed once a month by hand or in a dishwasher (60°) (please do not use a corrosive rinsing agent). Allow the filter to dry thoroughly and carefully replace it in the extractor hood. Avoid using alkaline dishwasher cleaning agents (ph value over 7).

When changing or washing a grease filter or carbon filter, after removal clean all exposed lower parts of the hood with a mild grease solvent. For the daily cleaning of the outer parts of the RESPEKTA CH 99060 WA use a soft cloth moistened with alcohol or a mild liquid cleaner. Never use an abrasive cleaner. Clean the filters in the dishwasher separately, not together with dishes.

Carbon filters (not delivered with the appliance)

1. Traditional carbon filters (normally round in shape) can be neither washed nor regenerated. The charcoal filters have to be replaced regularly, at least every 3 months or earlier, depending on the cooking habits.
2. Washable and regeneratable carbon filters (normally square in shape) are to be washed once a month in a dishwasher, using a standard rinsing agent and with the intensive rinsing program (at the highest temperature). Washable and regeneratable carbon filters absorb kitchen odours for a maximum of 3 years when cleaned monthly. The filter should then be replaced by a new item.

Washable and regeneratable carbon filters should be washed separately to avoid food residue deposits which can later cause unpleasant odours. After washing, the washable and regeneratable carbon filter must be reactivated. This is carried out by drying the cleaned filter in an oven for 10 minutes at 100°C.

Read the package to see whether your carbon filter is washable and regeneratable. If the package carries no information, then it contains a traditional, non-washable carbon filter.

The charcoal filters for recirculated air are to be fixed at the side of the motor.

When attached the carbon filter, the suction power will be lowered.

The charcoal filters should be changed at three or six months depending on your cooking habit.

The keys/switch functions are:

After connecting the RESPEKTA CH 99060 WA to the socket, the background lighting of all buttons is switched on. The LED display “A” does not light up. The RESPEKTA CH 99060 WA has no function and is in standby mode. The backlight of all buttons is automatically switched off after 2 seconds without any operation.

Tap the ON / OFF key “F”. The front cover of the cooker hood is opened. The backlight of this key is on, the motor is running at low speed and the light is on. The backlighting of the “B”, “C” and “D” keys lights up. Touch the ON / OFF “F” key again. The front cover of the hood is closed. The background lighting of all buttons goes out, the cooker hood is switched off and returns to standby mode. The “B” and “C” keys can only be operated when the cover is open.

The “D” key (light ON/OFF) can also be operated when the cover is closed.

Use the “B” and “C” buttons to select the required power level.

1. Tap the “C” key. The motor runs at the lowest power level.
2. Tap the “C” key again to go to the second power level.
3. Press the “C” key again to go to the third power level. At the respective power level, the display shows 1, 2 or 3.

To reduce the power level, press the “B” key repeatedly until the desired power level is shown on the display “A”.

To switch off the cooker hood, tap the ON / OFF button “F”.

Timer: With the timer button “E” you can set a running time of up to 5 minutes (with the device switched on). The motor and lights switch off automatically after the set time. The timer can be set again or switched off before the set time expires.

Attention! When a new power level is set after activating the timer, the timer will automatically be deactivated.

There are 2 sensors on the control panel (refer to O on the picture).

To operate the RESPEKTA CH 99060 WA in gesture sensor mode, follow the instructions below:

Wave your hand once from left sensor to the right sensor within 8 cm from the front of the sensors. The front cover of the cooker hood will be opened. The cooker hood will start to work at low speed and the LED display will show “1”. The lights will light on. The backlights of the following keys will be on: + ⏻ ⍟

Wave your hand from left to right again, the cooker hood works at mid speed and the LED display will show “2”. Wave your hand in the same direction as above for another time, the cooker hood works at high speed and the LED display will show “3”. Wave your hand in the same way again when the hood works at the highest speed, the hood will work at the same speed.

When you wave your hand from right to left once, the cooker hood will shift to a lower speed. When the hood works at high speed, wave your hand from right to left, the hood will switch to mid speed. The backlights of the following keys will be on: + ⏻ ⍟

When the hood works at mid speed, wave your hand from right to left, the hood will switch to low speed, and the LED display will show current speed level. If continuously reducing to no speed, the backlights will be off and all the function operation of the hood will not be available. The hood will then enter in standby mode. The above steps can be operated repeatedly.

If without any operation for functional buttons in 10 minutes, the gesture sensor will enter sleeping mode. Re-awake gesture function requires manual operation of any function buttons. The gesture function can be operated only when it has been activated.

Possible causes and solutions are:

Check the following:

1. Does the lamp need changing?
2. Has the lamp been properly fitted and seated in the holder up to the stop?
3. Is the fuse blown or has the circuit breaker tripped out?

If all the above checks fail to remedy the fault, it is possible you have a more serious problem. In no circumstances try to repair the electronic/electrical components in the appliance. Contact your Customer Service.

Check the following:

1. Is the size of the exhaust air pipeline sufficient?
2. Is the exhaust air duct blocked?
3. The cross section of the air pipeline (from the hood to the wall box incl.) should be 120 mm. A smaller air pipeline cross-section can possibly impair the motor power.
4. The air flow can be obstructed if the wall box is fitted with a fly mesh. If this is the case remove the fly mesh.
5. If the cover plate of the wall box has fixed, very inclined louvres, you should remove the plate to check whether this solves the problem. Mount a cover plate with movable louvres in the wall box, as this will least obstruct the air flow.
6. Is / are the filter(s) clean?
7. Was / were the carbon filter(s) installed more than six months ago? Then this/these should be changed.
8. Is the air taken from the kitchen being replaced by sufficient fresh air, so that no partial vacuum is being produced in the room?

The “D” key (light ON/OFF) can be operated even when the cover is closed.

Use the “B” and “C” buttons to select the required power level.

1. Tap the “C” key. The motor runs at the lowest power level.
2. Tap the “C” key again to go to the second power level.
3. Press the “C” key again to go to the third power level. At the respective power level, the display shows 1, 2 or 3.

To reduce the power level, press the “B” key repeatedly until the desired power level is displayed on display “A”.

With the timer button “E” you can set a running time of up to 5 minutes (with the device switched on). The motor and lights switch off automatically after the set time. The timer can be set again or switched off before the set time expires.

The sucked-in air is blown to the outside through the exhaust hose.

For this purpose, your house must have an exhaust air shaft or an exhaust air pipeline leading outdoors.

If the extractor hood has been fitted at the factory with a carbon filter, this must be removed. It is only practicable to use this when operating your hood in circulation mode.

If you wish to use an appropriately fitted hood as a circulation hood, you must mount the active carbon filter(s) to the fan motor before using the hood.

The active carbon filter(s) is/are included in the scope of supply with some models.

Otherwise you must obtain the active carbon filter(s) from the supplier of your extractor hood.

You must also change your hood over to the “Filter position” at the device provided (lever or ball handle) inside of the hood.

Minimum distance from the lower edge of the hood body:

The exhaust air line should be as short and straight as possible.

To avoid excessive noise or a reduced extraction capacity the diameter of the exhaust air pipeline should not be less than 120 mm.

Use or form only large radius bends. Small radius bends reduce the extraction capacity of the hood.

Use only smooth pipelines or flexible hoses of non-flammable materials for the exhaust air pipeline.

If the exhaust air pipeline is horizontally routed, there must be a minimum gradient of 1 cm per metre or an inclination angle of 2°.

If the exhaust air is directed into an exhaust air duct, the end of the entry fitting must be directed in the direction of flow.

If the exhaust air pipeline is routed though cool rooms, lofts etc. there can be a large temperature drop within the individual parts of the pipeline, resulting in sweating or condensation water production. This renders outlet pipeline insulation necessary.

In some cases a condensation water barrier must be installed in addition to adequate insulation (these are available from leading building material suppliers).

Otherwise condensation water could run into the extractor hood motor.

Check the following:

• Is the plug properly inserted in the socket?
• Is there a power supply failure?
• Has a fuse blown?

Check the following:

• Must the lamp be replaced?
• Was the lamp properly mounted and seated in the socket up to the stop?
• Is the fuse blown or has the circuit breaker tripped out?

If the documentation of the cooker hood does not include an instruction for replacing LED lamps, the lamp must be replaced by the customer service for safety reasons. See also chapter “Customer Service”.

A commercially available non-abrasive stainless steel cleaning agent should be used for cleaning stainless steel surfaces.

Treatment with a stainless steel preservative is recommended to prevent surfaces becoming quickly re-soiled. Apply the agent all over and economically using a soft cloth.

Never use stainless steel cleaning agents in the vicinity of the control elements.

When cleaning metal grease filters take care not to damage the mesh. Frequent cleaning or the use of aggressive cleaning agents can cause colour changes to the metal surface. These do not affect the filter function and are not grounds for complaint.

Do not use cleaning agents containing alcohol to clean appliances with a matt black finish. These can lead to discolouring.

When cleaning the area of the control elements, take great care to prevent water entering the electronics.

Avoid using alkaline dishwasher cleaning agents (ph value over 7) for cleaning washable and regeneratable carbon filters.