RAZER WOLVERINE V3 PRO (01) PDF Document

The product requirements for the RAZER WOLVERINE V3 PRO include:

• Xbox Series X|S or PC (Windows® 11 64-bit or higher)
• USB Type A port
• Internet connection for app installation

To register your product and score exclusive benefits for the RAZER WOLVERINE V3 PRO, you should go to the specified registration address.

The connectivity specifications for the RAZER WOLVERINE V3 PRO are:

• HyperSpeed Wireless via included dongle
• Wired Connection

The system requirements for the RAZER WOLVERINE V3 PRO are:

• Xbox or PC (Windows® 11 64-bit or higher)
• Internet connection for Razer Controller app

The RAZER WOLVERINE V3 PRO has Razer Mecha Tactile Action Buttons.

The multi-function buttons on the RAZER WOLVERINE V3 PRO include:

• 4 Mouse Click Back Paddles
• 2 Claw Grip Bumpers

The RAZER WOLVERINE V3 PRO features 2 Hall Effect Analog triggers with Mouse Click trigger stops.

The RAZER WOLVERINE V3 PRO includes a Carrying case for controller and accessories.

The USB Cable included with the RAZER WOLVERINE V3 PRO is a 3 m / 10 ft USB C to USB A cable.

To charge the RAZER WOLVERINE V3 PRO controller, use the included USB Type A to USB Type C cable to connect the controller to a power source (like a PC or console).

The charging status is indicated by the status indicator:

• Low Power (Blinking Red): <5%
• Charging (Breathing Orange): <100%
• Fully charged (Chroma Lighting): 100%

For best results, fully charge the controller before using it for the first time. A depleted battery will be fully charged in approximately 3 hours.

The RAZER WOLVERINE V3 PRO can connect wirelessly using the included dongle or via a wired connection using a cable. The controller prioritizes a wired connection via cable but will automatically switch to the dongle if a wired connection is not detected.

The wireless pairing notifications are as follows:

• Searching for dongle: Pulsing White
• Pairing with dongle: Blinking White
• Paired with dongle: Chroma Lighting

To power the RAZER WOLVERINE V3 PRO controller on, press the Xbox button. When it is On, the indicator will show Chroma Lighting. To power it Off, press the Xbox button again, and the lighting will be Disabled.

To utilize the trigger stop switches on the RAZER WOLVERINE V3 PRO:

• To Enable the trigger stops, move the switches inward (towards the center of the controller).
• To Disable the trigger stops, move the switches outward (away from the center of the controller).

To change the replaceable thumbstick caps on the RAZER WOLVERINE V3 PRO, pull the existing cap off the analog stick and align the new cap with the post on the analog stick, then press it down to secure it.

The Function Button Commands for volume and brightness control on the RAZER WOLVERINE V3 PRO are:

The Function Button Commands for Chroma lighting effects and speed control on the RAZER WOLVERINE V3 PRO are:

The Function Button Commands for adjusting Haptics Strength on the RAZER WOLVERINE V3 PRO are:

The Default Profile mapping for the Multi-Function buttons (M1-M6) on the RAZER WOLVERINE V3 PRO is:

• M1: X button
• M2: Y button
• M3: A button
• M4: B button
• M5: Left analog stick sensitivity clutch button
• M6: Right analog stick sensitivity clutch button

To reassign the Multi-Function buttons (M1-M6) mapping on the RAZER WOLVERINE V3 PRO:

Step 1. Hold down the Function button and the Multi-Function bumper/paddle you want to remap. The controller will enter Mapping Mode (Glowing White).

Step 2. Press the button you want to assign to it. A successful remapping will be indicated by the controller blinking Green.

Holding down the assigned button on the RAZER WOLVERINE V3 PRO will lower the chosen analog stick’s sensitivity by up to 50%.

This affects movement and aiming:

• Effect on movement: Changes from Default to Low Sensitivity.
• Effect on aiming: Changes from Default to Low Sensitivity.

The sensitivity clutch function can be assigned and customized through the Razer Controller app.

To unleash your controller’s full potential, install the Razer Controller app on your Xbox Series X|S or PC to customize its sensitivity clutch settings, multifunction button assignments, and much more.

To achieve maximum safety while using the RAZER WOLVERINE V3 PRO, adopt the following guidelines:

• If you have trouble operating the device properly and troubleshooting does not work, unplug the device and contact the Razer hotline or go to support for support. Do not attempt to service or fix the device yourself at any time.
• Do not take apart the device and do not attempt to operate it under abnormal current loads. Doing so will void your warranty.
• Keep the controller and all its parts and accessories out of the reach of small children to avoid accidents and/or injuries.
• Keep the device and its components away from liquid, humidity or moisture. Operate the device and its components only within the specific temperature range of 0°C (32°F) to 40°C (104°F). Should the temperature exceed this range, unplug and switch off the device in order to let the temperature stabilize to an optimal level.

The RAZER WOLVERINE V3 PRO requires minimum maintenance. Once a month, it is recommended to unplug the device and clean it using a soft cloth or cotton to prevent dirt buildup. Do not use soap or harsh cleaning agents.