RAND MCNALLY RVND 7 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD RAND MCNALLY RVND 7 (01) PDF MANUAL


PDF Content Summary: User Manual

FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful inter ference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and may cause harmful interference to radio communications if not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and the receiver. • Connect the equipment into an outlet that is on a different circuit from the GPS unit. • Consult the dealer or an experienced radio/TV technician for help. When using the device, ensure that the antenna of the device is at least 20cm away from all persons. IC Compliance Statement This device complies with Part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. IC Caution Intentional or unintentional changes or modifications to the equipment not expressly approved by Rand McNally could void the user’s authority to operate the equipment. IC attestation de conformité Ce dispositif est conforme à la norme FCC Partie 15 et aux norme(s) RSS permis-exempte(s) d’Industrie Canada. L’opération est soumise aux deux conditions suivantes: 3. Ce dispositif ne peut pas provoquer d’interférence nocive et 4. Ce dispositif doit accepter toute interference reçue, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif. Attention Les changements ou modifications à l’équipement, que ce soient intentionnelles ou non, non expressément approuvés par Rand McNally pourraient annuler l’autorisation de l’utilisateur à utiliser cet équipement. IC: 10199A-01001A

RVND™ 7 User Manual i

RVND™ 7 User Manual About GPS The Global Positioning System (GPS) is a constellation of satellites that a GPS receiver uses to calculate geographical positions. To determine a position, data from at least three satellites is required. To determine elevation, the data from four or more satellites is required. Accuracy of the positioning varies from 10 feet to several hundred feet, depending on vehicle placement and the surrounding environment. Geographical terrain (such as mountains), man-made structures (such as highway overpasses, bridges, and tall buildings), as well as weather can interfere with the GPS signal. For best GPS reception, position the device and mount with a clear line of sight to the sky. Some vehicles may have a limited view of the sky due to metal sun shields or a metallized windshield coating. Map data includes the geographical coordinates for address locations and points of interest (POIs). With GPS reception, your device calculates a route to your selected location. Customer Support Call toll-free: 800-333-0136 Service hours: Monday through Friday, 7 a.m. to 6 p.m. CT (Except official holidays) E-mail: RVNDSupport@randmcnally.com ii 1. Your Device .......................................................................................................................1 Safety Information ..........................................................................................................1 What’s Included ........................................................................................................... 2 Charge the Battery ...................................................................................................... 2 Install the Mount............................................................................................................. 2 Your RVND™ 7 ................................................................................................................ 3 2. Settings ............................................................................................................................ 4 Main Menu ...................................................................................................................... 4 Guide to RV Tools and Device Preferences.............................................................. 5 RV Info ...................................................................................................................... 6 Warnings ...................................................................................................................... 7 General Preferences ................................................................................................. 8-9 Route Preferences ........................................................................................................10 Map Preferences ........................................................................................................... 11 3. Destinations .....................................................................................................................12 Tips ................................................................................................................................13 New Location ..........................................................................................................14-17 Address Book ..........................................................................................................18-19 Multi-Stop Trips ..................................................................................................... 20-22 Tap Map .......................................................................................................................23 Avoid List .......................................................................................................................24 Points of Interest (POIs)........................................................................................ 25-28 Confirmation Windows................................................................................................30 Toll Costs, Route Compare..........................................................................................31 Look for this icon for help tips on many screens. Note: Some screens may appear different, depending on device model.4. Maps & Routing.............................................................................................................32 Table of Contents Route Map Window ....................................................................................................32 Exits Quick View............................................................................................................33 Directions Slide-Out List ...........................................................................................34 Virtual Dashboard ................................................................................................ 35-36 Junction View, Turn View ...........................................................................................37 Location and Route Options ....................................................................................38 5. Tools & Features ............................................................................................................39 RV Tools ....................................................................................................................39 Checklists........................................................................................................................40 Maintenance.................................................................................................................. 41 Trails ..............................................................................................................................42 Fuel Logs........................................................................................................................43 Quick Planner ............................................................................................................44 Road Atlas Information ...............................................................................................45 Unit Converter .............................................................................................................46 Calculator .....................................................................................................................46 6. Connect With Rand.......................................................................................................47 Rand McNally Dock .....................................................................................................48 TripMaker® ........................................... .........................................................................49 Custom POI Information .................................................................................... 50-51 Export Fuel Logs...........................................................................................................52 Tell Rand ....................................................................................................................53 More Information ........................................................................................................54

RVND™ 7 User Manual iii

Caution: Important Safety Information Navigation • Use this navigation device at your own risk. • Use this navigation device only when it is safe to do so. • Look at the display only when it is safe to do so. • Traffic regulations always have priority over any instructions from the navigation system. • Follow navigation system instructions only when local regulations and road traffic allow you do so. • Make sure that the mount is securely mounted and properly adjusted before each trip. • Note: If you do not understand the spoken instructions or are unsure of what to do next, refer to the navigation map on your navigation device. Installation • Make sure that the mount does not impair the driver’s visibility. • Do not attach the mount within the airbag deployment zone. • When installing the mount, make sure that it does not pose a risk in the event of an accident. • Do not run cables directly next to safety-relevant devices and power supplies. • After installation, check all safety-relevant equipment. • Connect the wall charger to a 120V or 240V outlet only. • Connect the vehicle charger to a 12V outlet only. 1. Your Device Device • Do not use sharp-edged objects on the device touch screen. • The device is not waterproof and is not protected against water dam age. • Protect the device from extreme temperatures. Operating temperature for the device is between 32 degrees F and 120 degrees F. • Do not open the navigation device casing. • Do not attempt to replace the battery. Contact Rand McNally Customer Support with questions about the battery. • Always follow local regulations when disposing of this device. • Note: Make sure that there are no kinks in the cable and that it will not be damaged by any sharp objects. • Note: Use only a moist cloth to clean the navigation device. • Note: Do not pull the cable to unplug the unit.

RVND™ 7 User Manual 1

What’s Included • Rand McNally RVND™ 7 • Windshield mount with suction cup • Quick Start Guide • Vehicle charger • USB cable Charge the Battery It is recommended that the device is always connected to a power source during use. Note: The vehicle may need to be on for the device to charge. 1. Your Device Install the Mount Note: Follow all local regulations governing the placement of the mount. 1. Select an area with a line of sight to the sky and GPS satellites. 2. Clean and dry the mounting area. 3. Remove the suction cup protective film. 4. Adjust the angle of the mount using the thumbscrew. 5. Pull the suction cup lever up to release suction. 6. Plug the USB cord into the device and the vehicle’s 12-volt power source. 7. Snap the device onto the mount. 8. Place and hold the mount suction cup against the mounting surface. 9. Press the suction cup lever down until it snaps into place. 10. Adjust the device so that it can be easily seen and does not block the driver’s line of sight. Snap into place Thumbscrew Snap into place Slide up to mount RVND™ 7

RVND™ 7 User Manual 2

1. Your Device 1 RVND™ 7 Your Device 1 Power Button

2 3 4 5 6 1 Press and hold to turn on or off. While the device is running, the power button can also be used for quick access to certain fea tures with one quick tap. Audio Output Connect to optional external speaker. SD Card Slot For future use, as needed. Mini-USB Port Connect the charger or the USB cord. Reset Button Use the reset button on the back of the device to restart. This will cancel the current route, but preferences, address book, and other personal data will be saved. Speaker

6 2 7 3 4 5 Start Your Device Each time you turn on your device, a new tip displays/ the Warning and Legal Consent window displays. • Tap the check to continue, or tap Don’t Show Tips to prevent these tips from showing again. •To view a short tutorial on device use, tap Tutorial. •Tap Accept, or if you turned the device off while on a route, tap Accept and Continue Previous Route.

RVND™ 7 User Manual3

1 4 2 3 2. Settings Main Menu 1 Battery Power Indicator 2 RV Tools Select to enter RV information, set warnings, and access other tools. 3 Go To Map Tap to view location on the map. 4 Choose Destination Tap to select an address or point of interest (POI). 5 Preferences 5 6 7 Tap to set general, route, or map options. 6 Mute/Unmute the Speaker Tap to mute or unmute spoken instructions. Note: You can also tap this icon when it appears on the map screen to mute/unmute. 7 Volume Tap to increase or decrease spoken instructions volume.

RVND™ 7 User Manual 4

1. Tap and to view the options. 2. Tap the option to be set. 3. Enter the new information. 4. Tap Back to save changes. RV Tools Page RV Info Bottles of Propane ............................................ 6 Size of Each Bottle ....................................... 6 Height ................................................................. 6 Number of Trailers ............................................ 6 RV ETA Adjustment ......................................... 6 RV Type ................................................................ 6 Total Length ........................................................ 6 Weight ................................................................. 6 Width ................................................................. 6 Warnings Auto Dismiss Warnings.....................................7 Construction Area...............................................7 Crossing State Border/ Time Zone Change Warning .................7 Curve Warnings...................................................7 Hill Warnings.........................................................7 Narrow Road Warnings.....................................7 Warning Display Size .........................................7 Speed ..................................................................7 State Border Alert ..............................................7 Toll Booth Alert ...................................................7 Warning/Alert Prompts ....................................7 Device Preferences Page General About ................................................................. 9 Align screen ........................................................ 9 Brightness ............................................................ 8 Clock Setting ....................................................... 9 Day/Night Mode ............................................... 8 GPS Status ........................................................... 9 Home Time Zone ............................................. 8 Keyboard ............................................................. 8 Language ............................................................. 8 My Custom POIs ............................................... 8 Quick Power Press ............................................ 9 Screen Click ......................................................... 8 Screen Snapshot Button ................................. 9 Shortcut Button .......................................9 Skin Style - Day .......................................8 Skin Style - Night .....................................8 Toll Prompt/Notification............................8 Tutorial ................................................................. 8 Units ................................................................. 8 Vehicle Type ........................................................ 8 Voice Name ........................................................ 8 2. Settings Device Preferences Page Route Cross-Country Borders ..................................10 Dirt Roads ...........................................................10 Fast Recalc ..........................................................10 Ferries ................................................................10 Freeways .............................................................10 Junction View Distance....................................10 Manage Avoid List............................................10 Recalculation .....................................................10 Route ................................................................10 Tollways ...............................................................10 Tunnels 10 Turn Announcements......................................10 Turn View Distance ...........................................10 U-Turns ................................................................10 Map Address Book Icons ..........................................11 Car Icon ................................................................11 Map Auto Zoom ...............................................11 Map Style .............................................................11 POI Icons .............................................................11 Route Color .........................................................11 RV Icon .................................................................11 RV POI Icons .......................................................11

RVND™ 7 User Manual 5

RV Info Options RV Info Options 2. Settings

RV Type Class A Class A w/Tag Axle Class B Class C Class C (Super) Fifth Wheel Hybrid Trailer Popup Trailer Toy Hauler Trailer Travel Trailer RV Camper Routing Style More Truck Like Between Truck and Car More Car Like Bottles of Propane Use the + and - buttons or enter a numeric value by tapping the calculator. Size of Each Bottle Use the + and - buttons or enter a numeric value by tapping the calculator. Number of Trailers 0 1 2 Total Length Use the + and - buttons or enter a numeric (RV + Trailers) value by tapping the calculator. Weight Use the + and - buttons or enter a numeric value by tapping the calculator. Height Use the + and - buttons or enter a numeric value by tapping the calculator. Width Use the + and - buttons or enter a numeric value by tapping the calculator. Number of Axles Use the + and - buttons or enter a numeric value by tapping the calculator.

RVND™ 7 User Manual 6

2. Settings Warnings Options Warnings Options Warning/Alert Prompts None Audio & Visual Visual Audio Auto Dismiss Warnings Never After 10 seconds After 30 seconds Height and weight violations will not be auto dismissed. Warning Display Size Full screen Small bar Curve Warnings Set warning distance to curves by using the + and - buttons. Hill Warnings Set warning distance to hills by using the + and - buttons. Narrow Road Warnings Set warning distance to narrow roads by using the + and - buttons. State Border Alert Set warning distance to state borders by using the + and - buttons. State or Province Border/ Timezone Change Warning Off On Toll Booth Alert Set warning distance to toll booths by using the + and - buttons. Construction Area Set warning distance to construction areas by using the + and - buttons. Construction information is based on RoadWork™ data distributed through the Rand McNally Dock. Speed Limit Warning Set the amount over the posted limit at which the warning appears. Set user-defined maximum speed to be warned whenever the vehicle exceeds that speed, regardless of posted speed limits. Speed Limit Change Set warning distance to speed limit Warning changes by using the + and - buttons. Note: To turn warnings off completely, tap the - button until “off” displays.

RVND™ 7 User Manual 7

2. Settings General Preferences Options General Preferences Options Skin Style - Day Ice Carbon Classic Skin Style - Night Ice Carbon Classic Vehicle Type RV Car Controls how routes are calculated. Note: Some tools and settings may not be available in car mode. Home Time Zone Hawaii Alaska Pacific Time Arizona Mountain Time Central Time Eastern Time Indiana (East) Atlantic (Canada) Newfoundland Day/Night Mode Always day Always night Automatic Day/Night Auto-Switch Use the arrows to select the number of Offset minutes. Brightness Set separately for day and night modes. My Custom POIs Tap Manage Custom POIs to specify how custom POIs are displayed on the map: set image, warning distance, warning type, and street/city/state level map display. Tap the “x” to delete any set of POIs. Toll Prompt/Notification Enabled Disabled Set whether or not you want to be asked about tolls when you calculate a route. Screen Click Click off Click on Tutorial View on-device tutorial Keyboard ABC Computer (QWERTY) Voice Name Samantha Tom (English only) Claudia (No street names) Language English Español Français For the screen and spoken instructions. Units U.S. Standard Metric Auto Select

RVND™ 7 User Manual 8 2. Settings General Preferences Options Clock Setting 12-hour clock 24-hour clock Screen Snapshot Button Off On Shortcut Button Main Menu Go to Map Set the shortcut that appears in the bottom right corner of the screen. Quick Power Press POI along route Screen snapshot Main Menu Show map Toggle mute Save current location Tell Rand The power button can also give you access to these screens at any time with one quick tap. Align screen Calibrate the touch screen. Note: Select this option if your device seems to have buttons that are hard to tap. GPS Status Tap to show details about your location. About Tap to show version information and copyrights. RVND™ 7 User Manual 9 2. Settings Route Preferences Options Route Preferences Options

Note: The default settings for your device are already optimized for RV routing. Use the options below to fine-tune these settings. A route may still include a roadway or maneuver set to Avoid if the only legal route found contains these types of roads or the route is over several hundred miles. Recalculation Increase ETA more Increase ETA some ETA OK Decrease ETA some Decrease ETA more Recalculation Manual recalculate Auto recalculate Route Fastest route Shortest route Freeways Allow all (default) Avoid freeways Prefer freeways Avoid small roads Tollways Allow tollways Avoid tollways U-Turns Allow u-turns Avoid u-turns Ferries Allow ferries Avoid ferries Cross-Country Borders Allow crossing borders Avoid crossing borders Dirt Roads Allow dirt roads Avoid dirt roads Tunnels Allow tunnels Avoid tunnels Manage Avoid List Roads States/Provinces AREAS Routes To avoid a state or province, select it from this list. Tap on the map and select a road, area, or route to add it to the Avoid List. Fast Recalc Off On Calculates a route to a midpoint between your location and the destination. Useful on long routes with frequent intersections. Turn Announcements Set three distances at which you want to be warned about an upcoming turn. The first announcement will be the farthest from the turn and the third the closest to it. Turn View Distance Set the distance before the maneuver at which the local street turn view screen appears. (Note: In 3D map view, this warning is not needed and will be turned off.) Junction View Distance Set the distance before the maneuver at which the highway junction view screen appears.

RVND™ 7 User Manual 10 2. Settings Map Preferences Options Map Preferences Options

Map View Heading Up North Up 3D View Map Style Light Dark Map Auto Zoom Off On, auto scale On, street scale On, city scale On, state scale Set to auto scale to keep the current vehicle position and the next turn in the map view at all times. Set to street/city/state scale to specify the maximum scale of the zoom. Note: Map redraw speed is impacted by autozoom, especially when combined with 3D map display option. POI Icons Off On Select icons to display on the map. Select restaurants, banks, and consumer POIs (“Other” category) to display on the map. RV POI Icons Off On Select parks, campgrounds, pet-friendly locations, and other RV POIs to display on the map. Address Book Icons Off On Address book entries appear as pushpin icons unless they are assigned to a group. Grouped entries appear as folders. RV Icon Use the arrows to select different icons to display when using the RV setting. Use the slider to change the color. Car Use the arrows to select different icons to display when using the car setting. Use the slider to change the color. Route Color Use the slider to select.

RVND™ 7 User Manual 11

Destinations 3. Destinations

1 2 3 4 5 6 7 To access this window from the Main Menu, tap Choose Destination. 1 Back Tap to return to the Main Menu. 2 New Location Tap to route to a new location by address, city center, intersection, or latitude/longitude. 3 History Tap to route to a recently entered location. 4 Address Book Tap to view a list of saved locations. 5 Multi-Stop Trips Tap to view a list of saved multi-stop trips or to create a new one. 6 Points of Interest/POIs Tap to search for a point of interest (POI) such as a gas station, restaurant, etc. Rand McNally Trips 7 Tap to view Rand McNally Trip content.

RVND™ 7 User Manual 12 3. Destinations Helpful Tips on Entering Addresses Auto-Complete Feature:

Tap to view a longer list of names matching the typed characters. Tap to view a list of previously selected locations. Add a space. Delete last character and move back one space. Use lowercase letters. Type an apostrophe, hyphen, or other symbol. Enter the first few characters in a name and a short list displays a couple of names that start with the typed characters. On the keyboard, the only keys available are for the next valid characters in a search name. Continue entering characters until the searched-for name displays in the list. Tap on the name to select it. Cities: Some cities with common names such as “Athens” have several types of names associated with a city. If a name does not display, continue typing characters until the name you are looking for displays in the list. Streets: If the next letter in the street name can not be selected on the keyboard, tap Expand Search to search a greater area. The Expand Search button can also help locate addresses that may actually be in a different town, spelled slightly differently, or in a neighboring town. Note: If you’re entering a State or County Route, it’s typically best to first ei ther enter the State or County initials (for example, State Road 535 would be entered as “SR”) but you may also need to try other options, such as “State Road” or “CA” for California, for example.

RVND™ 7 User Manual 13

4 1 2 3 New Location 1 Address 3. Destinations

5 6 Tap to route to an address by entering the city, street, and number, or by entering the zip code and street. 2 City Center Tap to route to a city center. 3 Intersection Tap to route to two intersecting roads in a city. 4 Back Tap to return to the previous window. 5 Enter Lat/Long Tap to route to a location by latitude and longitude. 6 Main Menu Tap to return to the Main Menu.

RVND™ 7 User Manual 14

Search for an Address 3. Destinations > Addresses

1. Tap Choose Destination > New Location > Address. 2. Type the first few characters in the city name. As you type, a short list of matching city names displays. 3. Tap on a city to select it. • If the city is not displayed on the short name list, continue typing characters in the city name or tap List to display a long list of city names. Use the up and down arrows to view all cities/states. Tap on a city to select it. Note: If a city name appears twice within a state, you may need to check both for your specific address. 4. Or tap Zip Code Search. Type the zip code. 5. Type the first few characters in the street name, or if the next characters of the street name cannot be selected on the keyboard, tap Expand Search and search a wider area. 6. Tap on the street name from the displayed list. 7. Tap the house number or tap List to show a list of address ranges and select a range. Note: To enter the House Number before the street, tap this button in step 5. This preference will be saved for subsequent address entry. 8. Tap on the street number range from the list. The Confirmation Window displays. 9. Tap Begin New Route to navigate to the location. RVND™ 7 User Manual 15

Route to a City Center 3. Destinations > Addresses

1. Tap Choose Destination > New Location > City Center. 2. Type the first few characters in the city name. 3. Tap on the city/state name. The Confirmation Window displays. 4. Tap Begin New Route to navigate to the location. Route to an Intersection 5. Tap Choose Destination > New Location > Intersection. 6. Type the first few characters in the city name. 7. Tap on the city name. 8. Type the first few characters in the primary street name, or if the next characters of the street name cannot be selected on the keyboard, tap Expand Search and search a wider area. 9. Tap on the street name in the list. 10. Type the first few characters in the intersecting street name. 11. Tap on the intersecting street name. The Confirmation Window displays. 12. Tap Begin New Route to navigate to the location. RVND™ 7 User Manual 16

3. Destinations > Addresses Route by Latitude/Longitude 1. Tap Choose Destination > New Location > Enter Lat/Long 2. Tap in the Latitude field. 3. Enter the latitude of the location and tap Enter. 4. Tap in the Longitude field. 5. Enter the longitude of the location and tap Enter. 6. Tap Go. The Confirmation Window displays. 7. Tap Begin New Route to navigate to the location. Note: There are two ways to enter latitude/longitude: by decimal degrees or by degrees, minutes, and seconds.

RVND™ 7 User Manual 17 3. Destinations > Address Book Address Book Add Locations to the Address Book from the Confirmation Window: 1. Tap Save to Address Book. 2. Tap Yes to accept the default name or tap No to display a keyboard. 3. Type the name of the location and tap Enter to save the location in the Address Book. The Confirmation Window re-displays. Entries • Tap Choose Destination > Address Book. Entries are alphabetically sorted by Name. • To sort by Distance or Date, tap Sort By. • Use the up and down arrows to scroll through the list or use the alphabet buttons on the left. • Tap the Search field to search the Address Book by keyword. • The notepad icon indicates a note has been added for this location. Route to an Address Book Location 1. Tap Choose Destination > Address Book. • Tap on the All Addresses tab or • Tap on the Groups tab. 2. Tap on an address to select it. The Confirmation Window displays. 3. Tap Begin New Route to navigate to the location. RVND™ 7 User Manual 18 3. Destinations > Address Book Create a Group 1. Tap Choose Destination > Address Book. 2. Tap on the Groups tab. 3. Tap New Group. 4. Type the group name. 5. To select a different color folder, tap . 6. Tap on a color, then tap Close. 7. When finished, tap Enter. Tap on the next to a group to delete the group. Addresses will still be saved in the Address Book. Note: You can also choose to display address book icons on the map. Add an Address to a Group 1. Tap Choose Destination > Address Book. 2. Tap the Groups tab. 3. Tap on the group you want to add an address to. 4. Tap New Location. 5. Tap Enter New Address, History, Address Book, or POI. 6. If you selected: • History, Saved, or POI, the selected location is added to the group. • Enter a New Address, tap Yes to accept the default name or tap No to display a keyboard and enter a new name. Remove an Address From a Group 1. Tap Choose Destination > Address Book. 2. Tap on the Group tab. 3. Tap on the Group you want to remove the address from. 4. Tap on the next to the address to be removed. 5. Tap Yes. RVND™ 7 User Manual 19 3. Destinations > Multi-Stop Trips Create a Multi-Stop Trip 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap New Trip. 3. Type the trip name. 4. To select a different color folder, tap . 5. Tap on a color, then tap Close. 6. When finished, tap Enter. Note: A multi-stop trip can include up to 50 stops. Add a Stop Note: You can add locations in the order you want to route to them or reorder stops later. 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap on the route. 3. Tap Add Address. 4. To add an address, tap Enter New Address, History, Address Book, or POI. 5. A Confirmation Window asks if you want to add another stop. Tap: • Yes to add another stop • No if the route is complete. 6. Tap Back to save changes. Remove a Stop 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap on the route. 3. Tap on the next to the stop to be removed. 4. Tap Yes. RVND™ 7 User Manual 20 3. Destinations > Multi-Stop Trips Reorder Routes Optimize Automatically After all locations have been added to a multi-stop trip, you can run the optimizer wizard to organize your trip. 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap on the route you want to optimize. 3. Tap Reorder Trip. 4. Tap Automatic/Optimize. 5. Tap Select First Stop and select the first stop, or No Preference. 6. Tap Select Last Stop and select the last stop, or No Preference. 7. Tap Yes to return to your current location to complete the route or No to complete the route at the last stop. 8. Tap Start Trip to begin the route. Note: There is a limit of ten stops that can be optimized automatically. Reorder a Route Manually 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap on the route you want to optimize. 3. Tap Reorder Trip. 4. Tap Manual. 5. Tap on the stop to be moved and tap the arrows to move stops up or down. 6. When finished, tap OK. 7. Tap Start Trip to begin the route. RVND™ 7 User Manual 21 3. Destinations > Multi-Stop Trips Select and Run a Saved Route 1. Tap Choose Destination > Multi-Stop Trips. 2. Tap on the route to select it. 3. Tap Start Trip. The Confirmation Window displays. 4. Tap Begin New Route to navigate to the location. 5. The device calculates the route to your first stop. When you have reached the stop, a message displays. 6. Tap: • Next Stop - To calculate a route to the next stop in the route. • Skip Next Stop - To skip the next stop and calculate a route to the stop after the next one. • End Current Trip - To end the route at the current stop. Note: To view your entire trip, select Summary Map View from the Route Display Options. Delete a Route 1. Tap Choose Destination > Multi-Stop Trips. The Multi-Stop Trips window displays. 2. Tap on the next to the route to be deleted. 3. A confirmation message displays. 4. Tap: • Yes to delete the route. • No to keep the route. RVND™ 7 User Manual 22 3. Destinations > Tap Map Tap on the Map

5 1 2 3 4 When you tap on the map screen, the crosshairs display. 1 Add as Via Add a via—an interim stop between the origin and the destination. 2 Avoid Tap to avoid the route, road, or area, or to detour. 3 Set Origin Set the location as the starting point of the route. 4 Route to Here Tap Begin New Route to navigate to the location.

RVND™ 7 User Manual 23

Avoid Options Avoid Route Avoid Area 3. Destinations > Avoid List Avoid List From the map, set specific locations to avoid. Tap on the map and select Permanent Avoid. Choose Avoid Route, Avoid Road, or Avoid Area. Or, if the location is along an active route, choose Detour. Avoid Route Choose whether to avoid an upcoming distance on an active route, in the left column, or a specific road section, in the right column. Or, select Avoid Entire Route. The route is recalculated and the avoided sections are added to the Avoid List, under Routes. Avoid Road Add the selected road segment to the Avoid List, under Roads. (Note: Reposition the map after zooming in or out to be sure to select the right location.) Road segments that have been permanently avoided are shown in pink on the map when zoomed in. Tap on a segment and tap Remove Avoid to remove the segment from the Avoid List. Detour Detour around a road segment on an active route. The route is recalculated, but the road segment is only avoided temporarily and does not appear on the Avoid List. To cancel the detour, tap the icon in the lower left-hand corner of the map screen and select Detour. Avoid Area Set an area on the map to avoid. Increase/decrease the size of the area using the and buttons. Tap Save to add the area to the Avoid List, under Areas. Enter a name for the area. If an active route has been entered, the route does not recalculate. Avoided areas are shown on the map in pink. To remove items from the Avoid List, tap Manage Avoid List in Prefer ences > Route. Tap the to remove. Tap Roads in the Avoid List to view avoided roads on the map. You may need to re-enter your destination to recalculate an active route.

RVND™ 7 User Manual 24

3. Destinations > POIs 5 1 2 Points of Interest (POIs) 1 My RV/Near Car 3 Tap to search for a point of interest near the current vehicle location. 2 City 4 Tap to search for a point of interest in a city. 3 My Route Tap to search for a point of interest along the vehicle route. 4 Destination 6 7 8 Tap to search for a point of interest near the route destination. 5 Back Tap to return to the previous window. 6 Custom POI Tap to select a custom POI location. 7 Quick Stops Tap to find a travel center near the current RV location. 8 Main Menu Tap to return to the Main Menu.

RVND™ 7 User Manual 25

3. Destinations > POIs 7 1 2 3 Points of Interest (POIs) 1 RV Campgrounds Tap to search for RV campgrounds. 4 5 6 2 RV Services Tap to search for an RV services POI. 3 Parking/Rest Areas and Border Crossings Tap to search for RV parking at rest stops and Walmart locations, and near border crossings. 4 Travel Centers Tap to search for a travel center. 5 Rand McNally Editor’s Picks Tap to search for national parks, festivals, and other places to visit. 6 Other Categories Tap to select from a wide range of restaurants, shopping, and other POIs. 7 Back Return to previous window.

RVND™ 7 User Manual 26

Other Categories 3. Destinations > POIs

1. Tap Choose Destination > Points of Interest. 2. Select a search type (My RV/My Car, City, My Route, or Destination). 3. Tap Other Categories. 4. Tap on a category (for example, Hospital/Emergency). Or use the Search bar to search by name. 5. If necessary, tap on a subcategory type (for example, Pharmacy). 6. Tap on a location from the list. or 7. Tap All. 8. Tap on the Spell button to display the keyboard. 9. Type the first characters in the POI name. 10. Tap on the POI name in the displayed list. RVND™ 7 User Manual 27 3. Destinations > POIs Select and Filter Commercial Campgrounds and Travel Centers To select only locations with amenities that you are interested in, filter your search results. 1. Tap Choose Destination > Points of Interest. 2. Select a search type (My RV/My Car, City, My Route, or Destination). 3. Tap Travel Centers. 4. Tap Select Services. 5. Click on the check box of each amenity to be included in the search. 6. Tap OK. The window displays POI locations with your selected amenities. 7. Tap on a location from the list. 8. A check next to Filter indicates the search terms have been applied. Tap Filter to return to general search results. Rate a Point of Interest You can rate campgrounds and other POIs from the Confirmation Window. For each POI, the top row of circles indicates the community rating from fellow drivers for the point of interest. The bottom row indicates your individual rating. 1. Tap on the POI Ratings button. 2. Use and to rate the facility. 3. Tap Create Comment and type a personal comment on the facility. 4. Tap Enter to save the comment. 5. Tap Back to save changes. Note: You can share ratings with fellow RVers through Rand McNally Dock software for your Mac or PC. RVND™ 7 User Manual 28

New Location 1 2 3. Destinations > Confirmation Windows Confirmation Windows 14 1 Destination Address 3 The selected location address. 2 Begin New Route

6 4 5 3 7 4 8 9 Tap to route to destination. Compare Routes Tap to choose between two routes. Add as Via Add this location as an interim stop between the origin and destination. This automatically makes the current route a multi-stop trip. Campground POI 6 7 14 1 2 3 4 5 Save to Address Book 5 Add the location to the Address Book or add to Address Book group. Atlas 6 Cross-reference to printed Rand McNally Road Atlas and Motor Carriers’ Road Atlas. (Page numbers apply to the most recent atlas.) Go to Map 7 Tap to view this location on a map. Set Origin 8 Tap to set the location as the starting point of a route. 8 10 11 Address Book 14 1 Menu 9 Tap to return to the Main Menu. POI Rating 10 Tap to rate or add a comment to this location, or view community ratings.

11 2 3 12 4 5 6 7 13 14 Details Tap to view detailed campground ratings and amenities. Edit Entry Rename or edit this entry in the Address Book. Note Add a note about this location in the Address Book. Back

8 12 13 9 Tap to return to previous window.

RVND™ 7 User Manual 29 3. Destinations > Toll Costs, Route Compare Toll Costs From the destination confirmation screen, tap Begin New Route. If the calculated route includes tolls, a message appears. Use Current Route 1 Show estimated toll costs and continue along the calculated route.

2 1 2 3 3 Compare Routes Compare the calculated toll route to an alternate route without tolls. (See below.) Don’t Prompt for Tolls Use the current route and disable this prompt for subsequent route calculations. Note: You can re-enable this prompt in Preferences > General.

Route Compare 1. From the destination confirmation window, tap Compare Routes to calculate and display two routes and choose between them. 2. Choose to ignore tolls and calculate two routes based solely on route preferences, or to calculate a primary route (which may include tolls) and an alternate route without tolls. 3. The top of the screen displays the total distance and time for each route, as well as any estimated toll costs. Zoom in to get a closer look at each route on the map. 4. Tap either button at the top of the screen to select that route. If the route includes tolls, estimated toll cost will display. RVND™ 7 User Manual 30

Route Map Window 3 12 4. Maps & Routing 9 Current Mile Marker Tap to open a “Tell Rand” message. 10 Current Information

1413 12 4 5 15 16 6 9 View current information by city, street, or upcoming intersection. Also dis plays advanced lane guidance and weather overlay key, when enabled. Tap to change. (Note: For some destinations, the “Am I close?” feature counts down addresses as the vehicle approaches.) City, county, and state Current street name Next intersecting street name Advanced Lane Guidance

7 1110 8 1 Next Maneuver 11 Location and Route Options Tap to see current location information, change route settings, detour, Tap to repeat spoken next maneuver instructions. 2 Road Name Name of street you will turn onto next. 3 Miles/Time Displays remaining distance. Tap to select from: home arrival time, arrival time, remaining time, home time, and elevation. 4 Exits Quick View Slide out to show upcoming exit information. 5 Directions Slide-Out List Tap to select a route display option. 6 Zoom In/Zoom Out 7 Main Menu 8 Compass Direction Tap to change the map display. An icon in the upper right corner displays the selected option: North up (N), heading up (arrow), or 3D (3). Also dis plays Wi-Fi status. cancel a route, and manage avoided roads. 12 Current Speed Tap to display the Virtual Dashboard. Turns red for speed warings. 13 Speed Limit Tap to open a "Tell Rand” message about speed limits. 14 Map View Tab Tap to simplify the map screen. Icons are minimized to show simply the zoom, next manueuver, and miles/time. 15 Traffic Tap to view the Traffic window. 16 Mute

RVND™ 7 User Manual 31

4. Maps & Routing Exits Quick View Slide out to show Points of Interest and amenities at upcoming exits. The list displays the distance to the next exit, exit name and number, and a count of available amenities. 1. Tap on an exit to bring up the notes icon . 2. Tap the icon to display local amenities by category. 3. Tap on any item in the list to route to that location.

RVND™ 7 User Manual 32

Highway View 1 2 3 45 Trip Summary (for multi-stop trips) 6 7 8 Summary Map View (entire trip) 6 4. Maps & Routing Directions Slide-Out List Route Display Options 1. When first opened, the slide-out list displays in Detail View, showing each maneuver. 2. Use and to view the instructions. 3. To change the display option, tap Route Display Options. See Highway View, Trip Summary, and Summary Map View at left. 1 Rise/Set Displays the times of sunrise and sunset for your current location. 2 MPH Displays the current vehicle speed, in miles per hour. 3 Distance, Time Displays remaining distance and time. 4 Distance Displays the distance to the next maneuver and the type of maneuver. 5 Street/Road Name Displays the street name you will be on after performing the next maneuver. Tap on any item in the list to view it on the map and to detour around it if necessary. (Note: For multi-stop tips, highways in each leg are listed, color-coded by segment.) 6 Total Distance and Time Total distance and time for the entire trip. 7 Leg Number of the leg and distance. 8 Leg Destination Leg destination.

RVND™ 7 User Manual 33

Tap here 1 2 3 4 9 106 4. Maps & Routing Virtual Dashboard To show the Virtual Dashboard, tap the Current Speed. 1 Current speed. Note: Turns red when speed limit warning exceeded. 2 Sunrise and sunset times based on vehicle location (latitude/longitude) and day. 3 Elevation at current location. 4 Percentage of current trip completed, distance to next maneuver, and the number of miles and time spent on the trip to this point. 5 Vehicle odometer. Tap the pencil to reset. 6 Gather trip information for up to three trips. Includes odometer settings, hours, and speeds. 7 Reset trip information for the selected trip (Tab 1, Tab 2 or Tab 3). 8 Select to automatically reset the information in each tab after the vehicle has remained stationary for the specified number of hours. 9 View fuel logs and add fuel purchase information.

5 8 7 10 Return to the Route Map Window.

RVND™ 7 User Manual 34 4. Maps & Routing Manually Reset Trip Information 1. Tap on the tab you want to reset. 2. To set the odometer for the selected tab back to zero, tap Reset All. 3. Information is captured as you travel the route. Automatically Reset Trip Information To reset trip information after the vehicle has remained stationary after a specific number of hours: 1. Tap on the tab you want to reset. 2. Tap Auto Reset. 3. Tap to increase the number of hours. 4. Tap to decrease the number of hours. 5. To save changes, tap Change. 6. The Tab displays the auto reset number of hours. RVND™ 7 User Manual 35

4. Maps & Routing 1 Junction View 2 3 4 56 When on a route, Junction View displays when you have an upcoming highway maneuver. Set distance in Preferences > Route. Once past the maneuver, Junction View closes and the previous window displays. 1 Signs to follow for the next maneuver. 2 Number and direction of lanes for the next maneuver. 3 Distance to the upcoming maneuver. Distance decreases as you approach the ramp. 4 Lane assist arrow. 5 Mute the speaker. 6 Return to previous window. Turn View Displays for upcoming turns. Set distance in Preferences > Route.

RVND™ 7 User Manual 36

1 5 4 2 3 4. Maps & Routing Location and Route Options 1 Nearest cross street 2 Current road you’re on, current town you’re in 3 Latitude and longitude at current location

6 10 7 8 9 11 12 4 Current location by mile marker 5 Return to previous window 6 Detour Around Part of the Route 1. On the left side of the window, tap the number of miles on the route to be avoided. 2. The route is recalculated. Around a Specific Roadway 1. On the right side of the window, tap and to view a list of roads in the current route. 2. Tap on one or more roadways to be avoided. A check mark appears in front of each selected road. 3. Tap Detour to recalculate the route. Note: Tap Cancel Detour to remove detours. 7 Detour the entire route and add it to the avoid list 8 Skip to next stop (for multi-stop trips) 9 Cancel current route 10 Save current location to the Address Book 11 Access list of avoided roads

12 Access Route Preferences

RVND™ 7 User Manual 37

1 2 3 4 5 6 7 8 9 5. Tools & Features RV Tools Note: Some features are not available in Car Mode. 1 Back Return to the Main Menu. 2 RV Info Enter RV information (weight, length, etc.). 3 Checklists, Maintenance, Trails, and Fuel View pre-trip and other checklists; maintenance notes; trails; and fuel purchase information. 4 Warnings Set warnings for hills, speed limits, and more. 5 Quick Planner Estimate the distance, driving time, and cost between any two cities or towns. 6 Road Atlas Information View emergency contact and other information. 7 Tell Rand Compose a message to send to Rand McNally when you connect to the Dock. 8 Converter Quickly convert distance, weight, and temperature. 9 Calculator

RVND™ 7 User Manual 38 5. Tools & Features Checklists 1. Tap RV Tools. 2. Tap Checklists, Maintenance, Trails, Fuel. 3. Tap the Checklists tab. To complete a preset checklist: 4. Tap on a checklist to select it. 5.Tap the box next to each task to check it off the list. Or To add a new checklist: 4.Tap Custom Checklist. 5.Enter the name of the new checklist. 6.Select the new checklist from the list. 7.Tap Add Item to add tasks. 8.Tap the box next to each task to check it off the list. 9. Tap Back to save changes. 10. If you have not checked off all the tasks, a warning displays. Tap Cancel to continue completing tasks, Uncheck All to clear all checklist tasks, or OK to save changes. 11. The Checklists tab redisplays, with the number of completed tasks on the right (for example, 2 of 28). To delete a checklist or an item from a checklist, tap . Note: If you delete preset checklists and want to restore them, tap Restore Default. RVND™ 7 User Manual 39 5. Tools & Features Maintenance Keep track of maintenance performed on your RV. 1. Tap RV Tools. 2. Tap Checklists, Maintenance, Trails, Fuel. 3. Tap the Maintenance tab. 4. Tap Add Note and enter the details. 5. Tap Back to save changes. Tap any note to edit or to change the date. To delete a note, tap . RVND™ 7 User Manual 40 5. Tools & Features Trails Use Trails to record a “bread-crumb” path of GPS coordinates where your RV has traveled. 1. Tap RV Tools. 2. Tap Checklists, Maintenance, Trails, Fuel. 3. Tap the Trails tab. 4. To record a trail, tap New Trail. 5. To end the trail, tap the Trails icon on the map screen. 6. The trail is recorded in the Trails tab. 7. Tap on a trail to view details. 8. Tap Show on Map to display the trail on the map screen. 9. Tap Edit Name to change the name of the trail. 10. Tap Set Color to change the color of the trail. Note: The Trails feature is also accessible from the Address Book. RVND™ 7 User Manual 41 5. Tools & Features Fuel Logs 1. Tap RV Tools. 2. Tap Checklists, Maintenance, Trails, Fuel. 3. Tap the Fuel tab to view a list of fuel logs by quarter. 4. Tap Add Fuel to record the date, location and cost of fuel purchase. 5. Tap on any field to edit. 6. Tap Save. 7. Once fuel purchases have been entered, tap on a quarter to view the details. 8. You can View by State or View by Month. 9. Tap the state or month to view fuel purchases. 10. Tap View All to see all fuel purchases. RVND™ 7 User Manual 42 5. Tools & Features Quick Planner Use this tool to quickly estimate the mileage and time between any two cities or towns. 1. Tap RV Tools. 2. Tap Quick Planner. The revenue or cost per mile used in the last computation displays. 3. Tap From City 1 and select the city. 4. Tap To City 2 and select the city. 5. The distance displays. 6. Tap Cost per Mile and enter the per mile rate or tap Total and enter the total amount. 7. Tap the new dollar amount and tap Enter. 8. The dollar amounts readjust automatically. 9. Tap Average Speed (MPH) enter a speed: • Tap -- or + to decrease or increase the speed. • Tap the calculator to enter a speed. 10. Tap Change. 11. The driving time displays. RVND™ 7 User Manual 43

5. Tools & Features Road Atlas Information To reference the Rand McNally Road Atlas and Motor Carriers’ Road Atlas: 1. Tap RV Tools. 2. Tap Road Atlas Information. 3. Select the appropriate country tab. 4. Select the appropriate state/province to view emergency and other key phone numbers.

RVND™ 7 User Manual 44 5. Tools & Features Unit Converter 1. Tap RV Tools. 2. Tap Converter. 3. Tap on the first field and select the type of conversion to perform. 4. Tap on the second field and enter the value to be converted. 5. Tap Enter. Calculator 1. Tap RV Tools. 2. Tap Calculator. RVND™ 7 User Manual 45

Rand McNally DockTM 6. Connect With Rand

The Rand McNally Dock enables you to receive software upgrades and access map updates, construction updates, and additional features. Simply download the Dock software for your PC or Mac at randmcnally.com/dock and connect your device using the USB cable provided. With the Rand McNally Dock, you can also: • Upload trips from TripMaker® to your device • Export fuel logs to your home computer • Upload custom POIs, such as red light cameras and railroad crossings, to your device • Access the Rand McNally support site and online store • Read product news and announcements • Send feedback and suggestions to Rand McNally through “Tell Rand” RVND™ 7 User Manual 46 6. Connect With Rand TripMaker® Use the TripMaker® online trip planning tool to create an itinerary, explore along your route, and add things to see and do. Send your customized itinerary to your RV GPS as a multi-stop trip. (Note: TripMaker® does not provide RV-specific routing. Your device will calculate a route, based on the vehicle and route settings, at the start of the multi-stop trip.) Access TripMaker on the Rand McNally Dock™ or go to: randmcnally.com/tripmaker. RVND™ 7 User Manual 47 6. Connect With Rand Custom POI Information Use custom POIs to upload lists of your own locations to your device. There are two types of custom POIs: 1. Destinations you can route to. 2. Alert locations, such as red light cameras and railroad crossings, you want to be warned about when they are along your route. Lists of custom POIs are available from third-party sources such as POI Factory: poi-factory.com. Or enter your own list. Tips for formatting your own list of POIs: 1. Files must be in .csv format. 2. You can enter locations by longitude/latitude (in decimal format), address, or both. 3. Separate each piece of information with a comma. Do not use spaces before or after commas. 4. Enter in order the longitude, latitude, location name, street address, city, state, zip, and country. For example: • Longitude/latitude and address: -87.761039,42.059611,Rand McNally,9855 Woods Dr,Skokie,IL,60077,USA • Longitude/latitude only: -87.761039,42.059611,Rand McNally • Address only: ,,Rand McNally,9855 Woods Dr,Skokie,IL,60077,USA (Note: In this example, there are two commas at the beginning. Commas are required as placeholders for fields with no data in them.) RVND™ 7 User Manual 48 6. Connect With Rand Custom POI Information To upload custom POI files to your device: 1. Connect your device to the Rand McNally Dock. 2. On the Dock, click Add Locations. You can also upload an Ad dress Book. 3. Click POI (for destinations) or Alert POI (for warnings). 4. Select the file from your computer. 5. Click Open to automatically transfer the file to your device. 6. Unplug your device from your computer. 7. Plug your device into power using the power adapter. 8. Turn the device on. 9. Depending on the size, the download could take up to 30 minutes. Note: “Failed records” are those for which some information was dropped from the records. If you would like to know why some records failed, plug your device into your computer, and view the error messages in the Dock. 10. Customize how you want the POIs to display in Preferences > My Custom POIs. RVND™ 7 User Manual 49

Export Fuel Logs 6. Connect With Rand

Use this feature to export fuel purchase information to your computer. The exported file can be in .xls or .csv format. On the Rand McNally Dock: 1. Click on Fuel. 2. Select where you want the file to be downloaded, and click Save. 3. The file is download to your computer. When finished, a notification message displays. 4. Click Ok. RVND™ 7 User Manual 50 6. Connect With Rand Tell Rand While you’re en route with your device, you can enter messages for Rand McNally regarding construction, vehicle restrictions, addresses, your device, and more. The next time you connect to the Rand McNally Dock, you can reopen, edit, and send the message. 1. Tap RV Tools. 2. Tap Tell Rand. On the left side, tap Current Location. Enter Different Location or Find Location on Map. Note: You can also open a Tell Rand message by tapping the speed limit or mile marker on the map screen, or with the power button by setting the Quick Power Press to Tell Rand. 3. If you selected Enter Different Location, enter it as an address. If you selected Find Location on Map, tap on the map to set the crosshairs at that location, then tap Back. 4. On the right side, tap the type of message you want to send. 5. Type your message. 6. Tap Enter to save the message. 7. To discard the message and return to the previous window, tap Back. 8. To send the message, connect your device to the Rand McNally Dock. 9. On the Dock, click Tell Rand to access and send the messages saved on your device. RVND™ 7 User Manual 51

For more information • Rand McNally Website randmcnally.com/rvgps • Support randmcnally.com/support • GPS accessories store.randmcnally.com • Rand McNally Dock randmcnally.com/dock • Facebook facebook.com/randmcnally 6. Connect With Rand

RVND™ 7 User Manual 52 Trademarks Rand McNally, the Rand McNally logo, the globe logo, TripMaker, and Best of the Road are registered trademarks and RVND and Rand McNally Dock are trademarks of RM Acquisition LLC, d/b/a Rand McNally. The RVer’s Friend is a registered trademark of TR Information Publishers. Good Sam is a registered trademark of Good Sam Enterprises, LLC. InfoGation is a registered trademark of InfoGation Corporation. © 2017 Rand McNally. © 2017 HERE. All rights reserved. Rand McNally follows a continuous improvement process and reserves the right to provide enhancements that may not be reflected in the pictures and specifications in this manual. The information contained herein may be changed at any time without prior notification. Neither this manual nor any parts thereof may be reproduced for any purpose whatsoever without the express written consent of Rand McNally, Inc., nor may it be transmitted in any form either electronically or mechanically, including photocopying, and recording. All technical specifications, drawings, etc. are subject to copyright law. RVND™ 7 User Manual 53 11/2017


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply