PYLE VINTAGE PTCWTRS80 (01) PDF Document

To install the stand, rubber feet of the whole unit, follow these steps:

1. Peel off the protect paper of the rubber feet.

2. Stick the rubber to the wooden stand.

3. Place the fiber ring between bottom of the main unit and the wooden stand then screwing the stand to the main unit in clockwise direction.

1. Connect the AC line cord to AC outlet and connect the speaker wire to the speaker terminal located on the rear side of unit (Red & Black wire connect to ‘R’ channel and White & Black wire connect to ‘L’ channel of speaker terminal).

2. Turn on the unit by On/Standby button and switch the Function button to “Tuner” function. If the LCD display light up with blue backlight, it means the power supply is normal. Now your system is ready to play the music.

1. Set unit in Standby Mode.

2. Press & hold the “MEM/CLK-ADJ” button, the LCD display will show “12H” and flashing. Press Skip Up or Skip Down button to select the appropriate area hour format (12HR/24HR). Press “MEM/CLK-ADJ” button again to confirm.

3. The LCD display will display the first & second digit of “00” is flashing. Press Skip Up or Skip Down button to set the correct hour. Press “MEM/CLK-ADJ” button to store the correct hour.

4. The third & fourth digit of “00” is flashing, press the Skip Up or Skip Down button to set the correct minutes. Then press “MEM/CLK-ADJ” button to store the correct minute.

1. Tune on the unit by press Power On/Standby button.

2. Press Function button to select “Tuner” mode and select the desired band by Random/Band button.

3. Tune to the required station by pressing the Skip Up or Skip Down button.

4. Adjust Volume Up/Down button to the desired volume level.

1. Press Function button to select “Tuner” mode and select the desired band by Random/Band button.

2. Press and hold the Skip Up/Down button for 1-2 seconds and then release.

3. The unit will start seeking automatically and stop until a radio station is reached.

4. Repeat step 2 until the desired radio station is being reached.

5. Adjust Volume Up/Down button to the desired volume level.

You can store up to 20 radio stations in the memory (10 FM/10 AM).

1. Set to Tuner mode.

2. Turn to the desired radio station by “Manual” or “Auto” tuning method.

3. Press “MEM/CLK-ADJ” button to enable program function & “MEM” icon and preset station NR will flash on LCD display.

4. Press “PRE-UP” or “PRE-DN” button to select the desired station memory for storage.

5. Press “MEM/CLK-ADJ” button again to confirm the setting.

6. Repeat step 2 to 5 to store other stations.

7. Now you can select the presets stations in order by pressing the “PRE-UP” button or “PRE-DN” button.

Note: The pre-set memories will be cancelled completely if dis-connecting the main power supply.

Before operating: Remove the stylus protector and place the cloth matt to the platter. Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured again afterwards.

1. Press Function button to select “Phono” mode.

2. Set the Speed Selector to the proper position depending on the type of record to be played.

3. Place the record on the platter (use the spindle adaptor if required).

4. Set the Cueing Lever to the up position.

5. Lift the tone arm from the rest and slowly move it to the record side. The platter will start to rotate and position the tone arm over the desired position of the record.

6. Pull down the Cueing Lever. The tone arm will come slowly on the recorder and start playback.

7. Adjust the Volume Up/Down button to the desired level.

8. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the record and return it to the rest position.

9. To stop intermediate, lift up the tone arm from the record and return it to the rest.

Connect another audio device, e.g. (portable) CD player, MP3 player, (portable) cassette player, iPod, etc. to this system via a cord with 3.5mm dia jack plugs (supplied).

1. Connect one end of this cord to the headphone jack of the external device and the other end to the Aux-In Jack at the rear side of the unit.

2. Then select the main function selector to “Phono” mode.

3. Start to playback your external device to enjoy your music.

Note: Due to Phono and Aux design in same channel of this unit, once the Aux-In jack plugged by any 3.5mm stereo plug, the Phono function will change to Aux In automatically and the turntable will stop to spin.

1. Press Function button to select “CD” mode.

2. Press “Open/Close” button to open the CD tray.

3. Place a CD with the printed side facing up inside the tray & then close the CD tray.

4. Focus search is performing, then will start the playback automatically.

Up to 20 tracks can be programmed for CD and play in any order. Before use, be sure the system is at stop mode before programming:

1. Set in CD mode & stop the CD playback.

2. Press the “MEM/CLK-ADJ” button, “MEM” icon and track no. will flash on LCD display. Moreover, it will indicate program no. to be programmed.

3. Select a desired track by pressing Skip Up or Down buttons.

4. Press the “Program” button to store the trace into memory.

5. Repeat steps 3 and 4 to enter additional tracks into the memory if necessary.

6. When all the desired tracks have been programmed, press CD “Play/Pause” button to play the disc in assigned order.

7. To cancel the programmed file, press “Stop” button until “MEM” is disappear on LCD display.

1. Press Function button to select “Tape” mode.

2. Put in the cassette tape.

3. Press Play key to active playback.

4. Adjust the Volume Up/Down control to the desired level.

5. Use Pause key when you want to stop playback temporarily.

6. Press Stop/Eject key when finished.

1. Select “Tape” mode from Function button and then set the High Speed Dubbing button to “Nor.” position.

2. Inset a pre-recorded cassette into Deck 2 and a blank cassette tape into Deck 1.

3. Press the “Pause” key and then press the “Record” and “Play” key at Deck 1.

4. Press the “Play” key to start playback at Deck 2 & then release “Pause” key at Deck 1 to start dubbing.

5. Press “Pause” key at Deck 1 & “Stop” key at Deck 2 when finish dubbing.

1. Press the Dubbing button to “HI” position and then follow the same procedures as stipulated in “Dubbing at Normal Speed”.

2. When dubbing a pre-recorded cassette tape at high speed, a chattering sound is being heard. To avoid this, set the volume control to a minimum level.

Note: Do not press the “High Speed Dubbing” button to HI or NOR position during dubbing, this will vary the speed of recording and may damage the cassette tape.

1. Select “Tuner” mode from Function button.

2. Tune to the desired station and insert a blank cassette tape in Deck 1.

3. Press “Record” & “Play” key to start recording.

4. Press “Pause” keys and then “Stop/Eject” key when finish.

1. Select “CD” mode from Function button.

2. Insert a black cassette tape in Deck 1 which suitable for recording.

3. Press “Pause” key first and then “Record” & “Play” key at cassette. Recording function is now on standby.

4. Start playback CD, and then press “Pause Key” at cassette to start recording.

5. To stop recording, press “Stop” button on CD mode first, then press the “Pause” key and then “Stop/Eject” key on cassette tape deck.

1. Select “Phono” mode from Function button.

2. Insert a blank cassette tape in Deck 1.

3. Press “Record” & “Play” key to start recording.

4. Select the desire record and start playback.

5. Press “Pause” keys and then “Stop/Eject” key when finish.

1. Press “Sleep” button and Sleep Indicator “zZZ” will shown on the LCD display.

2. Keep pressing the button to adjust the sleep timer in the order from 10>20>30….90 minutes respectively.

3. System will stop and go to standby mode automatically after the selected timing.

4. To cancel the sleep mode, press “Sleep” button until the display show “OFF” and “zZZ” indicator disappear on LCD display.

This function allows the system to turn on automatically and wake you up by CD or Radio mode respectively.

1. Wake Up Time: First, set the unit at standby mode and then press & hold the “Timer” button to enter the timer setting mode, the first two digits of clock will flashing. Press Skip Up/Down button to set the hour & then press “Timer” button again to confirm. Then press Skip Up/Down button to set the minutes & press “Timer” button to confirm.

2. Wake Up Source: Press the “Skip Up/Down” button to select the source from “CD” – “FM” repeatedly. Press “Timer” button again to confirm selected the source.

3. Wake Up Volume: Press Skip Up/Down button to set the wake up volume level from 1 to max. and then press “Timer” button to confirm.

The system will turn on automatically from standby mode once it reach the selected time and the timer indicator will flash on the display and unit will switch off automatically after running 60 minutes.

1. To active the timer function, press the “Timer” button repeatedly until the timer indicator (Clock icon) is shown on LCD display.

2. To cancel timer function by press again “Timer” button until the timer indicator (Clock icon) disappear.

This unit provides 4 differences sound mode to chance your listening experience. You can select the desired effect by pressing the “Preset EQ” button repeatedly at following sequence:

FLAT -> ROCK -> CLASSIC -> JAZZ -> POP