PYLE PRO PPHP1291 (01) PDF MANUAL

Before using your new Speaker System, please review the following instructions. Before connecting the speaker, make sure the system is off and the controls on the minimum level. On the contrary the system could damage.

1. – Plug the power cable to the AC outlet and to the system and to the speaker.

2. – Plug the Microphone in the “MIC” input.

3. – Connect (CD, DECK, MP3, DVD, etc) on “LINE IN” input.

4. – Turn on the systems. A green LED will light up to indicate the speaker is on.

5. – Set the volume on the low level on the MIC and the LINE IN input.

6. – Increase the master volume (place on the right side of LINE OUT* connector).

7. – Set TREBLE and BASS controls to equalize the sound.

8. – A red LED will light up when the system detects overload power. You will must decrease the volume.

Do not place the microphone against the speaker, it can cause feedback echo and it will damage the system.

6.3 and canon connectors marked as LINE OUT can handle an amplifier or even another powered speaker cabinet, in cascade. On the bottom of the speaker there is a hole to place a stand.

Model PPHP1291: 12″ 1000 Watt 2 Way Plastic Molded Speaker Cabinet

• 12″ Woofer

• 1.4″ Titanium Compression Driver

• 1/4″ and Speakon Jacks input

• Frequency response: 50-20 KHz

• Power: 1000 Watts

• Impedance: 8 ohm

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• Dimensions: W15.6″ x D12″ x H 23.3″

Model PPHP1294A: 12″ 1000 Watt Powered 2 Way Plastic Molded Speaker Cabinet

• 12″ Woofer

• 1.4″ Titanium Compression Driver

• Dual XLR and 1/4″ Mic Inputs

• XLR Stereo RCA Line Input

• XLR and 1/4″ Line Outputs

• Master Volume, Bass Treble Controls

• Frequency response: 50-20 KHz

• Power Output: 1000 Watts

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• 110/220 Voltage Selectable

• Dimensions: W15.6″ x D12″ x H 23.3″

Model PPHP1299AI: 12″ 1000 Watt Powered 2 Way Plastic Molded Speaker Cabinet w/Built in MP3 & Ipod Dock

• Power Switch and Digital amplifier.

• 12″ Woofer

• 1.4″ Titanium Compression Driver

• MP3 control with LCD display

• USB Terminal

• IPOD DOCK

• XLR and 1/4″ Mic Inputs

• XLR Stereo RCA Line Input

• XLR and 1/4″ Line Outputs

• Volume, Bass Treble Controls

• Frequency response: 50-20 KHz

• Power Output: 1000 Watts

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• 90-240V AC

• Dimensions: W15.6″ x D12″ x H 23.3″

Model PPHP1591: 15″ 1600 Watt 2 Way Plastic Molded Speaker Cabinet

• 15″ Woofer

• 1.75″ Titanium Compression Driver

• 1/4″ and Speakon Jacks input

• Frequency response: 40-22 KHz

• Power: 1600 Watts

• Impedance: 8 ohm

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• Dimensions: W18.2″ x D14.6″ x H 28″

Model PPHP1594A: 15″ 1600 Watt Powered 2 Way Plastic Molded Speaker Cabinet

• 15″ Woofer

• 1.7″ Titanium Compression Driver

• Dual XLR and 1/4″ Mic Inputs

• XLR Stereo RCA Line Input

• XLR and 1/4″ Line Outputs

• Master Volume, Bass Treble Controls

• Frequency response: 40-22 KHz

• Power Output: 1600 Watts

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• 110/220 Voltage Selectable

• Dimensions: W18.2″ x D14.6″ x H 28″

Model PPHP1599AI: 15″ 1600 Watt Powered 2 Way Plastic Molded Speaker Cabinet w/Built in MP3 & Ipod Dock

• Power Switch and Digital amplifier.

• 15″ Woofer

• 1.75″ Titanium Compression Driver

• MP3 control with LCD display

• USB Terminal

• IPOD DOCK

• XLR and 1/4″ Mic Inputs

• XLR Stereo RCA Line Input

• XLR and 1/4″ Line Outputs

• Master Volume, Bass Treble Controls

• Frequency response: 40-22 KHz

• Power Output: 1600 Watts

• Crossover Frequency: 3.5K Hz

• 35mm Speaker Stand Mount

• 90-240V AC

• Dimensions: W18.2″ x D14.6″ x H 28″

Microphone 1 input (1a): Allows you to connect a microphone with a 6,3mm connector.

Balanced microphone 1 input (1b): Connector for a balanced microphone.

Microphone 1 control (1c): Use this control to set the volume level of the microphone 1 (6,3mm or balanced).

Microphone 2 input (2a): Allows you to connect a microphone with a 6,3mm connector.

Balanced microphone 2 input (2b): Connector for a balanced microphone.

Microphone 2 control (2c): Use this control to set the volume level of the microphone 2 (6,3mm or balanced).

RCA Line-In (3a): Allows you to connect an external audio device (CD, radio, DVD, etc.), with RCA connectors.

Cannon Line-In (3b): Allows you to connect an external audio device (CD, radio, DVD, etc.), with a Cannon connector.

Control (3c): Use this control to set the volume level of the Line-In signal.

Volume control (4): Set the volume level.

Treble (5): Use it to set the treble level.

Bass (6): Use it to set the bass level.

Signal output (7a): Use this jack to connect other amplifier or even another powered speaker cabinet in cascade, using a 6,3mm connector.

Signal output (7b): Use this jack to connect other amplifier or even another powered speaker cabinet in cascade, using a Cannon connector.

AC 110/220 Voltage Selectable (8): This switch selects the AC input voltage.

AC power (9): Use it to connect the AC power cord.

On/Off power switch (10): Press to power on/off the speaker box.

Button (11a): Use it to On/Off MP3 player controller.

USB connector (11b): Use it to plug a USB device with MP3 file.

MP3 control (11c): Use this control to set the volume level of the MP3.

MP3 player controller (12): Controls for the MP3 player.

Ipod Dock (13): Dock for an iPod.

1/4″ jack self-lock (14): A self-locking input jack.

speakon jack (15): An input jack for a speakon connector.

	PPHP1291	PPHP1294A	PPHP1299AI	PPHP1591	PPHP1594A	PPHP1599AI
Woofer
Impedance:	8 ohms	4 ohms	4 ohms	8 ohms	4 ohms	4 ohms
Sensibility:	96 db/m/w	96 db/m/w	96 db/m/w	100 db/m/w	100 db/m/w	100 db/m/w
Frequency response:	43Hz-3KHz	43Hz-3KHz	43Hz-3KHz	30Hz-3KHz	30Hz-3KHz	30Hz-3KHz
Diameter:	12″	12″	12″	15″	15″	15″
Coil diameter:	1.5″	1.5″	1.5″	2″	2″	2″
Magnet:	30 oz	30 oz	30 oz	50 oz	50 oz	50 oz
Tweeter:
Impedance:	8 ohms	8 ohms	8 ohms	8 ohms	8 ohms	8 ohms
Sensibility:	106dB/m/w	106dB/m/w	106dB/m/w	110dB/m/w	110dB/m/w	110dB/m/w
Frequency response:	3KHz-22KHz	3KHz-22KHz	3KHz-22KHz	3KHz-22KHz	3KHz-22KHz	3KHz-22KHz
Coil diameter:	1.35″ Titanium diaphragm	1.35″ Titanium diaphragm	1.35″ Titanium diaphragm	1.75″ Titanium diaphragm	1.75″ Titanium diaphragm	1.75″ Titanium diaphragm
Magnet:	13 oz	13 oz	13 oz	23 oz	23 oz	23 oz
Built-in Amplifier	NO	YES	YES	NO	YES	YES
Output power max:	1000 Watts	1000 Watts	1000 Watts	1600 Watts	1600 Watts	1600 Watts
Dimensions:	W15.6″ x D12″ x H 23.3″	W15.6″ x D12″ x H 23.3″	W15.6″ x D12″ x H 23.3″	W18.2″ x D14.6″ x H 28″	W18.2″ x D14.6″ x H 28″	W18.2″ x D14.6″ x H 28″

All products are fitted with a detachable power cord (supplied) which connects to the AC Mains and the back panel of the loudspeaker. The power cord has an IEC female connector on one end and a male mains connector on the other end. This cord is supplied specifically to accommodate the different worldwide safety and electrical code requirements. The power cord supplied with your product has a 3-pin type plug. Do not cut off or damage the grounding plug. Like any electrical appliance, your EON powered speakers should not be used in water or when wet.

Product design and specifications are subject to change without previous notice.