PYLE PDICBT87 (01) PDF MANUAL

PYLE PDICBT87 (01) PDF SUMMARY:

What is an important step in obtaining the most realistic soundstage possible?

Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible.

---

Where should the front speakers be placed?

The front speakers should be placed the same distance from each other as they are from the listening position. They should be placed at about the same height from the floor as the listener’s ears will be, with the tweeters aimed toward the listener at ear-level height.

---

Where should the surround speakers be placed in a home theater configuration?

In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listener’s ears. If that is not possible, they may be placed in a wall (or in the ceiling) behind the listening position, facing forward.

---

What should the surround speakers provide?

The surround speakers should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers.

---

In Dolby Digital and DTS systems, where should the tweeters be aimed?

In Dolby Digital and DTS systems, aim the tweeters toward the listening position at ear-level height.

---

How do you connect the power supply to the active speaker?

The active speaker features the power supply for the speaker system. You may choose to use the included power supply adapter to connect directly into the active speaker’s power supply input. An optional power supply connection can be made by directly ‘hard-wiring’ power supply cables to the speaker’s power supply screw terminal post.

---

How do you create a speaker connection between the active and passive speaker?

Create the daisy-chain style speaker connection to allow speaker-to-speaker audio communication output. The included speaker wire is used to connect the active speaker to the passive speaker. Ensure proper speaker connection wiring between the speakers.

---

How do you pair your device to the speakers via Bluetooth?

Once the speakers are installed and powered, search the Bluetooth network name " Pyle Audio USA" on your device. Ensure the Bluetooth Receiver Switch is set to ON position. If you are prompted for a password, enter ‘0000’ (4 zeroes).

---

What tools are needed for installation?

• Pencil
• Measuring tape
• Carpenter’s level
• Phillips #2 screwdriver
• Utility knife
• Awl

---

What is the first step when installing the speakers?

Cut the drywall. Note: Always allow at least one-half inch between a wall stud and the speaker cutout or the locking tabs will not be able to swivel into place.

---

What is the second step when installing the speakers?

Connect the speaker wires to the speaker.

---

What is the third step when installing the speakers?

Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. Put in the strips of adhesive to secure the grill.

---

What is the fourth step when installing the speakers?

Replace the metal grill.

---

What is the fifth step when installing the speakers?

Complete.

---

What should you do if there is no sound from any of the speakers?

• Check that receiver/amplifier is on and a source is playing.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
• Review proper operation of your receiver/amplifier.

---

What should you do if there is no sound coming from one speaker?

• Check the “Balance” control on your receiver/amplifier.
• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.

---

What should you do if there is low (or no) bass output?

• Make sure the connections to the left and right “speaker Inputs” have the correct polarity (+ and -).
• Consider adding a powered subwoofer to your system.
• In Dolby Digital or DTS modes, make sure your receiver/processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/processor has been enabled. If no subwoofer is being used, make sure the left and right front and rear speakers have been configured as “LARGE”. See your receiver/processor’s owner’s manual for further information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.

---

What should you do if the system plays at low volume but shuts off as volume is increased?

• Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
• If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.

---

What are the features of the speaker system?

• Includes (2) Speakers (Active + Passive)
• Bluetooth Wireless Music Streaming Ability
• 2-Way Full Range Stereo Sound
• Built-in Digital Sound Amplifier
• Mounts Flush to Walls or Ceilings
• Screw Terminal Block Speaker Connectors
• Ability to Daisy-Chain Speakers for Stereo System Sound
• Environmentally Friendly ABS Construction
• Perfect for Custom Installations & Applications

---

What are the Bluetooth connectivity features?

• Includes Bluetooth Control Receiver
• Stream Wireless Audio from Your Connected Device (Smartphone, Tablet, Laptop, Computer, etc.)
• Bluetooth Network Name: ‘Pyle USA’
• Bluetooth Network Password: ‘0000’ (4 Zeroes)
• Bluetooth Version: 3.0
• Wireless Range: Up to 40’+ ft

---

What is included in the box?

• Active Speaker
• Passive Speaker
• 12V Power Adapter
• Speaker Connection Cable, 16’ ft.

---

What are the technical specifications of the speaker system?

• Impedance: 8 Ohm
• Power: 100/240V, 12V Power Adapter
• Sold as: Pair

---

Speaker Specifications:

MODEL	PDICBT57	PDICBT67	PDICBT87
Sound System	5.25’’ Speaker + 1’’ Tweeter	6.5’’ Speaker + 1’’ Tweeter	8.0’’ Speaker + 1’’ Tweeter
MAX Power Output	240 Watt	300 Watt	400 Watt
Efficiency	86dB	88dB	90dB
Frequency Response	100Hz-20kHz	70Hz-20kHz	50Hz-20kHz
Total Speaker Size	7.8’’ Diameter, 3.0’’ Depth	9.4’’ Diameter, 3.9’’ Depth	10.7’’ Diameter, 4.6’’ Depth
Cut-Out Size	7.0’’ Diameter, 2.9’’ Depth	7.9’’ Diameter, 3.7’’ Depth	9.6’’ Diameter, 4.4’’ Depth