PRO’SKIT NT-316 (01) PDF Document

The PRO’SKIT NT-316 is a 3-in-1 scanner with the following features:

• Detects Stud, Metal, and AC voltage.

• Calibrates automatically after turning on.

• Features a buzzer and LED indicator for detection.

• Provides a low battery indication.

• Powered by a 9V battery (6F22).

• Detection Depth:

– Stud mode (wood): Up to 3/4 inches (19mm).

– Metal mode: Up to 1 1/2 inches (38mm).

– AC voltage mode: Up to 2 inches (50mm).

You can use the PRO’SKIT NT-316 for the following applications:

• Find the wood or metal studs behind the walls.

• Find the metal pipes, rebar etc., behind the walls.

• Find the live AC wires behind the walls.

The main parts of the PRO’SKIT NT-316 scanner are:

1. Function Switch Button

2. LED Indicator

3. Test Button

4. Detection Area

5. Battery Cover

To install or replace the battery in your PRO’SKIT NT-316, follow these steps:

1. Open the battery cover on the back of the unit.

2. Connect a 9V battery to the battery connector.

3. Put the battery into the battery compartment.

4. Replace the battery cover.

To calibrate your PRO’SKIT NT-316, follow this procedure:

1. Select the desired mode (Stud, Metal, or AC) using the function switch.

2. Place the unit flat on the surface you wish to scan.

3. Press and hold the Test button. The unit will beep and the LED will flash. Calibration is complete when the beeping and flashing stop, and the LED turns off.

4. While keeping the Test button pressed, you can now begin scanning the surface.

Important: The PRO’SKIT NT-316 must be calibrated over a spot with no studs, metal or AC voltage. If it is calibrated over one of these, it will not detect anything. In this case, move the unit to a new spot and try the calibration again.

When the LED on your PRO’SKIT NT-316 flashes after you press the Test button, it indicates that the battery is low and should be replaced.

The PRO’SKIT NT-316 can find the edges of wood or metal studs up to 3/4 inch (19mm) deep. To do this, follow these steps:

1. Slide the function switch to the “Stud” position.

2. Hold the unit flat against the wall.

3. Press and hold the Test button. The unit will perform a self-calibration. Wait for the beep sound and LED to stop flashing before moving the unit.

4. While holding the Test button, slide the unit slowly across the wall surface.

5. When the edge of a stud is detected, the LED will light up and the buzzer will sound. Mark this spot.

6. Continue sliding the scanner. When the LED turns off and the buzzer stops, you have passed the other edge of the stud. Mark this second spot.

7. The center of the stud is located between the two marks you have made.

The PRO’SKIT NT-316 can find metal objects like rebar and pipes up to 1 1/2 inches (38mm) deep. Follow this procedure:

1. Slide the function switch to the “Metal” position.

2. Hold the unit flat against the wall.

3. Press and hold the Test button. The scanner will perform a self-calibration. Wait for the beep and flashing LED to stop.

4. While holding the Test button, slide the unit slowly across the surface.

5. When a metal object is detected, the LED will light up and the buzzer will sound.

The PRO’SKIT NT-316 can detect live AC wires up to 2 inches (50mm) deep. Use the following steps:

1. Slide the function switch to the “AC” position.

2. Hold the unit flat against the wall.

3. Press and hold the Test button. The scanner will perform a self-calibration. Wait until the beep and flashing LED stop.

4. While holding the Test button, slide the unit slowly across the surface.

5. When a live wire is detected, the LED will light up and the buzzer will sound.

Please note the following warning for the PRO’SKIT NT-316: The AC voltage detection feature is not designed to indicate whether a circuit is live or dead. It only indicates the presence of AC voltage. Always turn off the power when working near wiring. Static electricity building up on the wall surface can cause inaccurate detection.

Several factors can affect the performance of your PRO’SKIT NT-316:

• Shielding on wallpaper or freshly painted walls that are not completely dry can interfere with the scanner.

• Always use caution when nailing, cutting, or drilling in walls, floors, and ceilings that may contain wiring or pipes.

• Sensing depth and accuracy can be affected by moisture, content of materials, wall texture, and paint.

• The PRO’SKIT NT-316 is designed for interior use only.

• Do not rely exclusively on the detector to locate items. Use other information sources like construction plans or visual identification of pipe and wiring entry points.