POWERWERKS PWRS1 (01) PDF MANUAL

Exposure to extremely high noise levels may cause a permanent hearing loss. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures:

According to OSHA, any exposure in the above permissible limits could result in some hearing loss. Earplugs or protectors in the ear canal or over the ears must be worn when operating this amplification system to prevent a permanent hearing loss.

1. Read all safety and operating instructions before using this product.

2. All safety and operating instructions should be kept for future reference.

3. Read and understand all warnings listed on the operating instructions.

4. Follow all operating instructions to operate this product.

5. This product should not be used near water, i.e. Bathtub, sink, swimming pool, wet basement, etc.

6. Only use dry cloth to clean this product.

7. Do not block any ventilation openings. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.

8. Do not install this product near any heat sources; such as, radiators, heat registers, stove or other apparatus (including heat producing amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

10. Protect the power cord from being walked on or pinched, particularly at Plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord.

11. Only use attachments specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation ports or any other openings.

15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way.

16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

17. When the MAINS plug, or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

18. Protective Ground Terminal: The apparatus shall be connected to an AC main socket with a protective earth ground connection.

CAUTION – RISK OF ELECTRIC SHOCK DO NOT OPEN: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CHASSIS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Lightning Bolt Symbol: This symbol is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

Exclamation Point Symbol: This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND THAT NO OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.

MPE Reminding: To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

1. CH1 / CH2 LINE IN / MIC IN Mix jack: Combination input jack for channels 1 and 2.

2. LINE IN/MIC IN Switch of CH1 / CH2: Selects between line level and microphone level input for the corresponding channel.

3. Volume control of CH1 / CH2: Adjusts the volume for the corresponding channel.

4. Effect volume control of CH1 / CH2: Adjusts the reverb effect level for the corresponding channel.

5. Bass control of CH1 / CH2: Adjusts the low frequencies for the corresponding channel.

6. Treble control of CH1 / CH2: Adjusts the high frequencies for the corresponding channel.

7. DSP modes elector switch and mode indicator: Selects between four DSP EQ settings (MAIN, MONITOR, DJ, SPEECH).

8. Bluetooth® pairing button: Press to pair your Bluetooth device.

9. Link button: Press on both speakers to link them for stereo sound.

10. Indicator lamps: Includes a signal indicator, power supply indicator, and limit indicator.

11. Subwoofer volume control: Adjusts the volume of the subwoofer.

12. The whole device volume control (MASTER): Adjusts the overall volume of the system.

13. CH 3/4 volume control: Adjusts the volume for channel 3/4.

14. CH 3/4 3.5mm input jack (AUX IN): Input for devices using a 3.5mm audio cable.

15. CH1 / CH2 / CH 3/4 / Bluetooth® Mixed Signal LINE OUT: Output to send a mixed signal to another device.

16. CH 3/4 RCA input jack: Left and Right RCA inputs for channel 3/4.

17. CH 3/4 6.35mm input jack: Left and Right 1/4″ inputs for channel 3/4.

18. Main power switch: Turns the unit on and off.

19. FUSE IEC mains inlet: Connection for the main power cord and location of the fuse (T5A L 250V).

1. Prior to switching on, turn volume down to minimum.

2. Connect the audio source to the appropriate Input socket.

3. Connect to the mains supply.

4. Switch on the audio source, followed by the active speaker.

5. Set the volume with the applicable control.

6. Adjust the bass + treble.

1. Press and hold the PAIR button until light flashes quickly.

2. Pairing connection can now be made via Bluetooth® on devices such as smart phones and tablets.

3. To temporarily bypass Bluetooth® connection press PAIR button once until light flashes slowly. Press again once to reconnect.

4. To exit/disable Bluetooth® press and hold PAIR button until light turns off.

• Do not overload the box to avoid damage to the speakers.

• Do not place an open fire (candles, etc.) on top or next to the box – FIRE HAZARD.

• For indoor use only. If the box is used outdoors, you need to make sure that no humidity can enter the box.

• When not in use, unplug the unit from the mains.

• Unplug the unit from the mains prior to checking or replacing the fuse.

• Make sure that the box is placed on a stable, strong surface.

• Do not place liquids on the box and protect it against humidity.

• Only use suitable means of transportation to move the box. Do not attempt to lift without support.

• Always unplug the unit during a thunderstorm or when it is not in use.

• If the unit has not been used for a long period of time, condensation can occur inside the housing. Please let the unit reach room temperature prior to use.

• Never try to repair the unit yourself. It does not contain any user serviceable parts.

• Run the mains lead in such a way that nobody can trip over it and nothing can be put in it.

• Set the unit to the lowest volume prior to switching it on.

• Keep the unit out of the reach of children.

(1) 10″ Sub

(1) Satellite column with speakers

(1) Spacer Column

(1) Carry bag for column pieces