POWERWERKS PWR10 (01) PDF MANUAL

1. Read all safety and operating instructions before using this product.

2. All safety and operating instructions should be kept for future reference.

3. Read and understand all warnings listed on the operating instructions.

4. Follow all operating instructions to operate this product.

5. This product should not be used near water, i.e. Bathtub, sink, swimming pool, wet basement, etc.

6. Only use dry cloth to clean this product.

7. Do not block any ventilation openings. It should not be placed flat against a wall or placed in a built-in enclosure that will impede the flow of cooling air.

8. Do not install this product near any heat sources; such as, radiators, heat registers, stove or other apparatus (including heat producing amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord being walked on or pinched, particularly at Plugs, convenience receptacles and the point where they exit from the apparatus. Do not break the ground pin of the power supply cord.

11. Only use attachments specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Care should be taken so that objects do not fall and liquids are not spilled into the unit through the ventilation ports or any other openings.

15. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way; such as, power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally or has been dropped.

16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.

17. When the MAINS plug, or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.

18. Protective Ground Terminal: The apparatus shall be connected to an AC main socket with a protective earth ground connection.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE CHASSIS. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the unit.

Apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.

This device complies with Part 15 of the FCC Rules / Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

To satisfy FCC / IC RF exposure requirements, a separation distance of 20 cm or more should be maintained between the antenna of this device and persons during device operation. To ensure compliance, operations at closer than this distance is not recommended.

1. Prior to switching on, turn volume down to minimum.

2. Connect the audio source to the appropriate Input socket.

3. Connect to the mains supply.

4. Switch on the audio source, followed by the active speaker.

5. Set the volume with the applicable control.

6. Adjust the bass + treble.

1. Press and hold the PAIR button until light flashes quickly.

2. Pairing connection can now be made via Bluetooth on devices such as smart phones and tablets.

Press PAIR button once until light flashes slowly. Press again once to reconnect.

Press and hold PAIR button until light turns off.

Intended for Indoor or protected from weather use only.

Do not place near open flame.

Make sure unit is stable. Place on a flat surface or an appropriate speaker stand with wide footprint able to hold 25 lbs. or greater.

Do not place liquids on top of unit or subject to high humidity.

No user serviceable parts inside. Always refer to a qualified repair service when service is required.

Mind the system Clip Indicator. Keeping the volume to a level that keeps the Clip Indicator only blinking when a large amount of bass is present will deliver a better listening experience and prolong the life of the unit.

The PWR12 details are:

The PWR10 details are: