PIMA CLM351 (01) PDF DOCUMENT

The PIMA CLM351 is an Ethernet-to-3G cellular transmitter that allows the Hunter-Pro Series and Captain 8 intruder alarm systems to communicate over a cellular network. It replaces the GSM-200 transceiver. The transmitter is supplied mounted on a bracket that is adapted to the alarm system housing.

The CLM351 is based on PIMA net4pro Ethernet card and Teltonika RUT230 router, and it supports 3G network.

The CLM351 is supplied without a SIM card.

• Operating voltage: 12VDC

• Current consumption: 100mA (max)

• Weight: 360 gr

• Operational temperature: -10 to +50 °C

net4pro

• Fully panel integrated

• Ethernet: LAN, WAN

RUT230

• Mobile: 3G HSPA+ Up to 14.4 Mbps; UMTS; EDGE; GPRS;

• Power supply: 9-30 VDC, 4-pin DC connector

• SIM: 1 x external SIM holder

• Status LEDs: 2 x connection type status, 5 x connection strength, 2 x LAN status, 1 x Power

• Auto Failover

• Connection monitoring: Ping Reboot, Periodic Reboot, Wget Reboot, LCP and ICMP for link inspection

• CLM351 Transmitter

• Antenna

• This guide

• SIM Needle

• Have a clear line of sight to the sky (where possible)

• Be clear and free of obstacles

• Be clear of metal objects

• Be located away from other transmitting devices

• Be securely affixed the antenna in location

Important: Disconnect the control panel from AC and battery power before installing the CLM351.

Follow the next steps to install the transmitter.

1. Push the RUT230 SIM holder button with the supplied SIM needle, and pull out the SIM holder.

2. Insert the SIM card given by your ISP (Internet Service Provider) into the SIM holder. Mind the card orientation.

3. Slide the SIM holder back into the router.

4. Mount the bracket at the top of the control panel’s box using the supplied screws.

5. Attach the 3G antenna.

6. Connect the Molex harness of the CLM351 to the SERIAL connector on the control panel.

7. Connect the control panel to power. Check the net4pro’s Status and network LEDs illuminate, and check the router’s reception LEDs to check the signal strength.

8. Program an encryption into the net4pro using the Comax software.

9. Set the transmitter in the control panel as described in the setup instructions.

10. Test the transmitter by generating events.

1. In an LCD keypad, enter the Technician code.

2. Press ‘3’ (Communication) and press ENTER (MS1 Options).

3. Press and hold the asterisk key (*) for two seconds (to enable the Advanced Programming menu).

4. Press BACK (Advanced Prog.) and press ENTER (Choose Provider).

5. Press BACK (Network Settings) and press ENTER (MS1 URL/IP).

6. Enter the CMS’s IP address and port number (IP:port) and press ENTER.

7. Press END X 2 (Advanced Prog.), BACK X 4 (Serial Output) and press ENTER (LNLN).

8. Press NEXT and press the pound key (#) under N (Network MS 1) to enable it (+).

9. Press Enter and then END to exit the menu.

10. If Account No.1 is not set, go to the Communication menu, press NEXT, ENTER X 2 and set it.

If the CLM351 replaces the GSM-200 transceiver, do the steps that follow in addition to the standard setup steps:

1. Repeat steps 1-2 of the standard setup (Enter Technician code, press ‘3’ for Communication and ENTER for MS1 Options).

2. Press NEXT X 6 (GSM Transmitter) and press ENTER (GSM Settings).

3. Press ENTER (GRTYS) and press the pound key (#) under G (GSM Tx Installed) to disable it (-).

4. Press ENTER and press END to exit the menu.

• CLM351: P/N 8300031