Free English PHANTEKS GLACIER R260 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD PHANTEKS GLACIER R260 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What is included in the package contents of the PHANTEKS GLACIER R260?
The following items are included in the package contents:
| Item | Quantity | Notes |
|---|---|---|
| R260 Reservoir | 1 | |
| Fan Bracket | 1 | |
| Pump Bracket | 1 | |
| Stop Fitting | 1x | (pre-installed) |
| Plug Fitting | 4x | (pre-installed) |
| M3x8 Bracket Screws | 4x | |
| M4x25 Pump Screws | 4x | |
| Fan Screws | 4x | |
| D-RGB cable | 1 | |
| D-RGB Motherboard cable | 1 | |
| 2.5mm Allen Key | 1 |
What warnings and disclaimers should be noted before installing the PHANTEKS GLACIER R260?
This product is intended for advanced users. Please consult with a qualified technician for installation. Phanteks assumes no liability for any damages occurring as a result of using Phanteks cooling products.
Power down the system before installation.
Do not disassemble the reservoir/pump. Warranty will be voided.
Perform a leak test before turning on the system.
Check the website for the latest installation guide.
How should I prepare the water loop and pump installation for the PHANTEKS GLACIER R260?
The PHANTEKS GLACIER R260 is equipped with multiple ports to allow for more flexibility. Please plan your water loop before proceeding with installation.
Regarding the Optional Pump (De)Installation: The D5 pump can be easily deinstalled or installed with the 4x M4 pump screws. Tighten the screws in a diagonal sequence.
Make sure the o-ring is seated correctly and tightened evenly.
Tighten the pump screws evenly in a diagonal pattern for an even pressure.
After the screws are tightened, it is normal that there will be a small gap between the pump bracket and the acrylic.
How do I install the fan brackets on the PHANTEKS GLACIER R260?
Mount the 2x Fan Brackets directly to a 120mm or 140mm fan with the 4x Fan Screws.
How do I install the aluminum cover on the PHANTEKS GLACIER R260?
Step 1. Deinstall the aluminum cover from the reservoir and keep the 2x M4x25 screws for STEP 4.
Step 2. Mount the aluminum cover on the fan brackets with the 4x M3x8 screws.
The aluminum cover can be installed in 4 different positions. Find the correct position and slide the aluminum cover up or down for your setup.
What is the procedure for securing the reservoir to the aluminum cover on the PHANTEKS GLACIER R260?
Secure the reservoir to the aluminum cover with the 2x M4x25 screws.
How do I connect the D-RGB lighting on the PHANTEKS GLACIER R260?
Connect the D-RGB LED-strip to other Phanteks D-RGB lighting products.
Daisy chain Phanteks D-RGB products.
Optional: use the motherboard adapter to connect to the motherboard.
What steps should I follow when powering on the PHANTEKS GLACIER R260 for the first time?
Make sure all connectors and fittings are tightened.
Connect the pump to a power source.
Fill the reservoir and let the pump run until all air is released.
Let the pump run for multiple hours. Tilting the system can help to release air bubbles.
What performance checks should be done for the PHANTEKS GLACIER R260?
For optimal performance please check the following:
Make sure the pump never runs dry.
Close any unused ports with Stop Fittings.
Always perform a leak test before turning on the system.
CLICK HERE TO DOWNLOAD PHANTEKS GLACIER R260 (01) PDF DOCUMENT