PERLICK 9277A (01) PDF MANUAL

PERLICK 9277A (01) PDF SUMMARY:

How do I prepare the cabinet for plumbing?

No plumbing connections are required. Condensate from the cooling coil is automatically evaporated through a condensate pan located in the condensing unit section.

---

What are the electrical requirements for the cabinet?

The cabinet must be connected to a separately fused power source (see Electrical Specification Plate) and grounded in accordance with National and Local Electrical Codes. Caution: Do not attempt to operate the equipment on any other power source than that listed on the Electrical Specification Plate.

---

What bottle sizes can the Perlick Bottle Coolers accommodate?

Perlick Bottle Coolers are provided with adjustable partitions which will accommodate various bottle sizes.

---

What should I do with bottles before placing them in the cooler?

• Remove bottles from their cases before placing in cooler to ensure proper air flow.
• For maximum efficiency, bottles should be corded.

---

Where should I place the cabinet?

To assure maximum performance, fresh air must be allowed to circulate through the machinery compartment. It is important to allow at least two inches of clearance at the back or left end of the cabinet. Do not place anything on the top or in front of the cabinet that would obstruct air flow at these grilles.

---

How should the cabinet be leveled?

Cabinet should either be leveled or pitched slightly toward the drain to allow any accumulated water to flow out.

---

How can I seal the base of the cabinet to the floor?

For sanitation purposes, it may be necessary to seal the base of the cabinet to the floor. This can be accomplished by laying a bead of silicone sealant along the base of the cabinet.

---

Where is the adjustable temperature control located and how is it set?

An adjustable temperature control is located inside the bottle cooler on the evaporator fan panel assembly. It is factory set at approximately 38° F. Make adjustments as shown to attain the desired temperature. Note: A temperature setting that is too low will not allow enough condensing unit “off” time to maintain a frost-free coil.

---

How often should the condenser be inspected and cleaned?

The condenser (located behind the front grille) should be inspected every 30 days, and cleaned, if necessary. Failure to keep the condenser clean will cause a loss in condensing unit efficiency.

---

How often should the doors be inspected and cleaned?

Doors should be periodically removed from the cabinet and inspected for a buildup of foreign materials, such as syrups, beer, etc. Buildups on the underside of the doors, along with the cabinet breaker strips on which they ride, will cause them to bind, and therefore, not function as designed. If dirty, these surfaces should be cleaned with a silicone lubricating material. Aerosol silicone sprays can be obtained locally at most department or automotive stores.

---

How do I remove the doors?

To remove doors: Lift front of door upward and slide forward until door clears the cabinet top. Use the reverse procedure to reinstall the doors.

---

How do I clean the cabinet?

Use a damp cloth with a mild detergent and water to clean the inside and outside of the cabinet. Dry thoroughly. Do not allow cleaning agents or large amounts of water to go down the drain. Use an acceptable stainless steel polish to clean all stainless steel surfaces.

---

What are the parts common to all Roll Top Bottle Coolers?

Part No.	Description
C31088BL	Black
C31088SS	Stainless steel
C15909	Cap Opener
C17332AL	Aluminum
C17332BL	Black
C17332SS	Stainless steel
C11279	Door Assembly with lock
C16038-1	Door gasket – front
C6661-1	Door gasket – back
C22258R	Replacement lock kit
C16037-1	Left wire partition
C8485-1	Center partition
C8484-1*	Main wire partition
C8487-1	Left bottom rack
C16325-1	Main bottom rack
C6757-1	Bin sub-divider
C4963-1	Breaker strip – right front
C4963-2	Breaker strip – left front
C9774	Center door mullion – stl. stl.
C7190-1	Door end rail – stl. stl.
C30313-1	Front grille
C30008-1	Condensate pan
C12829PG	Temperature control

*For Model Nos. 9277 & 9278 Only.

---

What are the replacement parts for a 9276A-UL 2 Door Roll Top Bottle Cooler?

Part No.	Description
57500	Compressor- R134a
57513	Condenser fan motor
C3150-3	Condenser fan blade
C12545A	Evaporator fan motor
C25397-1	Evaporator fan guard
C10510	Complete evaporator assy.
C8467	Fin coil assy.
C6147	Evaporator fan blade
C32207-1	Wire harness assy.

---

What are the replacement parts for a 9277A-UL 3 Door Roll Top Bottle Cooler?

Part No.	Description
57498	Compressor- R134a
57513	Condenser fan motor
C3150-3	Condenser fan blade
C12546A	Evaporator fan motor
C25397-1	Evaporator fan guard
C10511	Complete evaporator assy.
C8469	Fin coil assy.
C6154	Evaporator fan blade
C32207-1	Wire harness assy.

---

What are the replacement parts for a 9278A-UL 4 Door Roll Top Bottle Cooler?

Part No.	Description
57597	Compressor – R134a
C15250A2	Condenser fan motor
C15250A3	Condenser fan blade
C12546A	Evaporator fan motor
C25401-1	Evaporator fan guard
C5934A	Complete evaporator assy.
C8474A	Fin coil assy.
C6159	Evaporator fan blade
C32208-1	Wire harness assy.

---

How do I avoid stainless steel corrosion?

Corrosion can be prevented by following product cautions, cleaning instructions and avoiding use of certain chemicals or objects which will cause stainless steel corrosion.

---

What are the stainless steel enemies and their results?

Stainless Steel Enemy	Result
Steel wool or steel scouring pads	Small particles break off, lodging in the surface and rusting begins.
Cherry/Onion/Olive juice	Sets up a galvanic action that can transfer enough metal to cause pin hole leaks.
Chlorine Bleach	Bar rags soaked in bleach and thrown into a stainless steel sink will cause the stainless to develop pin hole leaks after a very short period of time.
Sharp objects	Dropped into a stainless steel sink will cause a puncture dimple and over time will appear as a pin hole leak.

---

What are the recommended cleaning agents for stainless steel and their uses?

Job	Cleaning Agent*	Comments
Routine Cleaning	Soap, ammonia, detergent	Apply with sponge or cloth. Can be used on all finishes.
Fingerprints and smears	Areal 20, Lac-O-Nu, Lumin Wash O’Cedar Cream Polish, Stainless	Provides barrier film to minimize fingerprints. Can be used on all finishes.
Stubborn stains and Discolorations	Allchem Concentrated Cleaner, Samae, Twinkle, Zud Restoro, Grade F or FFF Italian Pumice, Whiting or Talc, Liquid Nu Steel, Copper’s or Revere Stainless Steel Cleaner, Lumin Cleaner, Sta-Clean, Cameo Copper Cleaner, Allen Polish Highlite, Penny-Brite, Copper Brite	Rub lightly, using dry or damp cloth in the direction of polish lines on the stainless steel.

*use of propriety names is intended only to indicate a type of cleaner and does not constitute an endorsement. Omission of any proprietary cleaner does not imply its inadequacy. All products should be used in strict accordance with instructions on the package.