PANASONIC PT-RS11K (02) PDF Document

Before transporting the projector, remove the dust sponge from the mounting portion of the projection lens and store it for future use. When transporting the projector, remove the projection lens before attaching the dust sponge. Otherwise dust will accumulate inside and may cause malfunctions.

Transport the projector with 2 or more people. Failure to do so may drop the projector, which may result in damage or deformation of the projector, or injury.

When transporting the projector, hold it securely by its bottom and avoid excessive vibration and impacts. They may damage the internal components and result in malfunctions.

Do not transport the projector with the adjustable feet extended. Doing so may damage the adjustable feet.

1. Open the cover.

2. Insert the batteries and close the cover (insert the negative side first).

When removing the batteries, perform the steps in reverse order.

If you control the multiple projectors with a single remote control, use commercially available M3 stereo mini jack cables to connect to the REMOTE 1 IN / REMOTE 1 OUT terminals of the projectors.

Use a cable that is 15 m (49’3″) or shorter, with 2 core shielded. The remote control may not operate when the length of the cable exceeds 15 m (49’3″) or when the shielding of the cable is inadequate.

Install the projector on a flat surface so that the front of the projector is parallel to the screen surface and the projection screen is rectangular.

If the screen is tilted downward, the projection screen can be adjusted to be rectangular by adjusting the front adjustable feet. The adjustable feet can also be used to adjust the projector to be level when it is tilted in the horizontal direction.

Adjustable feet can be extended by turning them. Turning them in the opposite direction will return them to the original position.

Adjustable range: Adjustable feet: Approx. 12 mm (15/32″) each

Attention: Be careful not to block the intake/exhaust ports with your hands or any objects when adjusting the adjustable feet while the light source is on.

Attention: Replace the projection lens after turning off the power of the projector.

1. Insert the projection lens by aligning the mark on the projection lens (orange) with the mark on the projector (E to the left of LOCK) and turn clockwise until it clicks.

2. Secure the projection lens with the supplied lens fixing screw. Use a Phillips screwdriver to secure it in screw hole A located to the right of mark on the projection lens (orange).

Note: Some lenses may not have a screw hole A for securing the projection lens. Turn the projection lens counterclockwise to confirm that it does not come out.

1. Remove the lens fixing screw. Use a Phillips screwdriver to remove the first screw to the right of the mark on the projection lens (orange).

2. Remove the projection lens by turning it counterclockwise while pressing the lens release button. Turn the projection lens counterclockwise until the mark on the projection lens (orange) is aligned with the mark on the projector (E to the left of LOCK).

Attention: Store the removed projection lens where it will be free from vibration and impact. Store the removed lens fixing screw in a safe place.

Make sure that the supplied power cord is securely fixed to the projector body to prevent it from being removed easily. Confirm that the MAIN POWER switch is on the OFF side before connecting the power cord.

1. Check the shapes of the AC IN terminal on the side of the projector and the power cord connector, then insert the connector completely in the correct direction.

To remove the power cord:

1. Confirm that the MAIN POWER switch on the side of the projector is on the OFF side, and remove the power plug from the outlet.

2. Remove the power cord connector from the AC IN terminal of the projector while pressing the lock button.

1. Connect the power cord to the projector.

2. Connect the power plug to an outlet.

3. Press the ON side of the MAIN POWER switch to turn on the power. The power indicator ON (G)/STANDBY (R) lights in red, and the projector enters the standby mode.

4. Press the power on button. The power indicator ON (G)/STANDBY (R) lights in green and the image is soon projected on the screen.

1. Press the power standby button. The [POWER OFF(STANDBY)] confirmation screen is displayed.

2. Press the arrow buttons to select [OK], and press the ENTER button. (Or press the power standby button again.) Projection of the image will stop, and the power indicator ON (G)/STANDBY (R) on the projector body lights in orange. (The fan keeps running.)

3. Wait for a few seconds until the power indicator ON (G)/STANDBY (R) of the projector body lights up in red (fan is stopped).

4. Press the OFF side of the MAIN POWER switch to turn off the power.

Using the control panel:

1. Press the LENS button on the control panel. Pressing the button changes the adjustment screen in the order of [FOCUS], [ZOOM], and [SHIFT].

2. Select each item and press the arrow buttons to adjust it.

Using the remote control:

1. Press the lens buttons (FOCUS, ZOOM, SHIFT) on the remote control.

• FOCUS button: Adjusts focus.
• ZOOM button: Adjusts zoom.
• SHIFT button: Adjusts shift.

2. Select each item and press the arrow buttons to adjust it.

1. Move the lens to the ET-D75LE90 lens standard position. While the shift adjustment screen is displayed, press the DEFAULT button on the remote control to display the [HOME POSITION] screen. Select [D75LE90] to move the lens to the lens standard position.

2. Adjust the focus at the center of projected image.

3. Loosen the lock screw and turn the periphery focus adjustment ring by hand to adjust the focus in the periphery of the screen.

4. Check the focus at the center of the image again and make fine adjustments.

5. Tighten the lock screw.

You can switch the input directly by pressing the input selection button (RGB1, RGB2, VIDEO, S-VIDEO Y/C, DIGITAL LINK, DVI-D, HDMI, SDI) on the remote control or control panel.

Alternatively, you can display the input selection screen:

1. Press the INPUT MENU button. The input selection screen is displayed.

2. Press the INPUT MENU button again. The input will switch each time you press the button.

1. Press the SHUTTER button. The image disappears.

2. Press the SHUTTER button again. The image is displayed.

Note: The power indicator ON (G)/STANDBY (R) will blink slowly in green while the shutter function is in use (shutter: closed).

1. Press the ID SET button on the remote control.

2. Within five seconds, press and set the one-digit or two-digit ID number set on the projector body using the number (0 – 9) buttons.

If you press the ID ALL button, you can control the projectors regardless of the ID number setting of the projector body.

If the DEFAULT button on the remote control is pressed, the values adjusted in the menu items are restored to the factory default settings.

1. Press the DEFAULT button on the remote control.

Note: You cannot reset all the settings to the factory default at a time. To reset all the settings adjusted in the sub-menu item to the factory default one at a time, execute the [PROJECTOR SETUP] menu -> [INITIALIZE].

1. Press arrow buttons to select [PICTURE MODE] in the [PICTURE] menu.

2. Press left/right arrow buttons.

3. Press left/right arrow buttons to switch the item. Options include: STANDARD, CINEMA, NATURAL, DICOM SIM., DYNAMIC, GRAPHIC, USER.

1. Remove the air filter cover. Use a Phillips screwdriver to turn the air filter cover screw counterclockwise until it turns freely, and then remove the air filter cover.

2. Pull out the air filter unit from the tabs on the projector body while slightly pressing the grip on the air filter unit inward.

3. Wash the air filter unit. Soak it in cold or warm water and lightly rinse it. Do not use cleaning tools such as brushes. Rinse two to three times using fresh water.

4. Dry the air filter unit naturally in a well-ventilated place not exposed to direct sunlight.

5. Attach the air filter unit to the projector, matching the protrusion position with the grooves. Hook the frame to the tabs.

6. Attach the air filter cover and tighten the screw.

Light source indicators (LIGHT1 / LIGHT2):

Temperature indicator (TEMP):

Filter indicator (FILTER):

• Is the power plug firmly inserted into the outlet?
• Is the MAIN POWER switch set to OFF?
• Is the wall outlet supplying electricity?
• Have the circuit breakers tripped?
• Are the light source indicators LIGHT1/LIGHT2 or the temperature indicator TEMP lighting or blinking?

• Are connections to external devices correctly performed?
• Is the input selection setting correct?
• Is the BRIGHTNESS adjustment setting at a minimum?
• Is the external device that is connected to the projector working properly?
• Is the shutter function in use?
• If the power indicator ON (G)/STANDBY (R) is blinking in red, consult your dealer.
• Is the lens cover still attached to the lens?

• Are the batteries depleted?
• Is the polarity of the batteries set correctly?
• Are there any obstructions between the remote control and the remote control signal receiver of the projector?
• Is the remote control being used beyond its effective operation range?
• Are other forms of light, such as fluorescent light, affecting the projection?
• Is the REMOTE CONTROL setting in CONTROL DEVICE SETUP set to DISABLE?
• Is the REMOTE 2 IN terminal used for contact control?
• Is the ID number setting operation correct?