PANASONIC KX-TDA100 (03) PDF Document

Step 1. Insert a flathead screwdriver into the opening on the left of the screw cover and unlatch it. Turn the screw anticlockwise to loosen.

Step 2. Slide the front cover to the right until it stops and then lift it off.

Step 1. Hook the front cover onto the shelf by lining up the protrusions on the cover with the receptacles on the shelf.

Step 2. Slide the front cover to the left until it locks into place.

Step 3. Turn the screw clockwise to tighten and secure the screw cover.

The SD Memory Card must be inserted into the card slot on the MPR card before the system starts. Ensure the card is pushed in securely until it clicks or seats properly within the slot.

Do not remove the SD Memory Card while power is supplied to the PANAIC KX-TDA100. Doing so may cause the system to fail to start when you try to restart it.

Step 1. Insert the power supply unit along the guide rails.

Step 2. Push the release lever in the direction of the arrow so that the unit engages securely with the connector on the back board.

Step 3. Turn the 4 screws clockwise in the order numbered 1 to 4 to fix the unit.

To protect the back board from static electricity, do not touch parts on the back board in the main unit, the power supply unit, or the optional service cards. Discharge static electricity by touching ground or wearing an earthing strap before handling components.

Step 1. Insert the card along the guide rails.

Step 2. Hold the card and push the release lever in the direction of the arrow so it engages securely with the connector on the back board.

Step 3. Turn the 2 screws clockwise to fix the card in place.

Be sure to cover each slot in which no optional service card is installed by using a Blank Slot Cover.

For the Amphenol connector, use a shielded twisted pair cable. For the RJ45 connector, use a twisted pair cable.

Using a cable diameter of 0.5 mm, the maximum length is 1128 meters for SLT.

Using a cable diameter of 0.5 mm, the maximum length is 720 meters.

Using a cable diameter of 0.5 mm, the maximum length is 229 meters.

Step 1. Loosen the screw on the frame.

Step 2. Insert a user-supplied earthing wire.

Step 3. Tighten the screw.

Step 4. Connect the other end of the earthing wire to earth.

The earthing wire must have green-and-yellow insulation, and the cross-sectional area of the conductor must be more than 0.75 mm squared or 18 AWG.

Step 1. Slide the System Initialise Switch to the SYSTEM INITIALIZE position.

Step 2. Plug the AC power cord into the unit and an AC outlet, then turn it on. The RUN indicator will flash.

Step 3. While the indicator is flashing, slide the System Initialise Switch back to the NORMAL position.

Step 4. Wait for the initialisation process, which takes about 1 to 3 minutes. The process is successful when the RUN indicator stops flashing and stays lit.

All existing data will be cleared and the PANAIC KX-TDA100 will be set to default factory values.

You can connect the PC using a USB cable connected to the USB port, or an RS-232C cross cable connected to the RS-232C port on the unit.

Ensure that both connector cases of the RS-232C cross cable are conductive to maintain frame ground. If they are not, you must connect the frame of the PANAIC KX-TDA100 to the frame of the PC using an earthing wire to prevent differences in electrical potential.

Step 1. Connect your PC to the PANAIC KX-TDA100 via USB or RS-232C.

Step 2. Start the Maintenance Console application on your PC.

Step 3. Handle the “Information before programming” window by reading it and clicking OK.

Step 4. Enter the installer level programmer code (default is INSTALLER) and click OK.

Step 5. Click Connect.

Step 1. Select the PANAIC KX-TDA100 model from the list.

Step 2. Choose either the USB or RS-232C tab based on your connection method.

Step 3. Enter the system password for the installer (default is 1234).

Step 4. Click Connect.

Step 1. Click OK to initiate the replacement of country or area data on the PANAIC KX-TDA100. This may take several minutes.

Step 2. Follow the system restart procedure described in the manual to restart the unit.

Step 3. Reconnect the Maintenance Console after the restart.

Step 1. Within the Configuration menu of the Maintenance Console, click Slot.

Step 2. Move the mouse pointer over the BRI card to display the option menu.

Step 3. Click Ous.

Step 1. In the Maintenance Console, go to Tool and select BRI Automatic Configuration.

Step 2. Click Check to turn on the BRI card and click OK.

Step 3. Enter the subscriber number for the desired ports in the Subscriber field.

Step 4. Click Execute.

Step 5. Click the Check Box for the desired ports.

Step 6. Click Data Apply and then click Close.

Step 1. Within the Configuration menu, click Slot.

Step 2. Move the mouse pointer over the BRI card to display the option menu.

Step 3. Click INS.

Step 1. Under CO & Incoming Call, click DIL Table & Port Settings.

Step 2. Ensure the DIL tab is selected.

Step 3. Configure the required settings.

Step 4. Click OK.

Step 1. Under CO & Incoming Call, click DDI / DID Table.

Step 2. Configure the required settings.

Step 3. Click OK.

Step 1. Under CO & Incoming Call, click DIL Table & Port Settings.

Step 2. Click the DDI / DID / TIE / MSN tab.

Step 3. Set the Distribution Method for the desired ports to MSN.

Step 4. Click OK.

Step 5. Click MSN Table and then click the MSN tab.

Step 6. Configure the required settings and click OK.

Step 1. Under Configuration, click Slot.

Step 2. Move the mouse pointer over the extension card and click Ous.

Step 3. Move the pointer over the card again and click Port Property.

Step 4. Set the Type to DSS for DPT Type and assign the Location No., then click OK.

Step 5. Under Extension, click DSS Console.

Step 6. Select the pair extension number and assign features to buttons, then click OK.

Step 7. Finally, set the card back to in-service by going to Slot under Configuration and clicking INS.

Go off-hook, dial the extension number, and begin speaking.

Go off-hook, dial the automatic line access number (usually 9 or 0), dial the outside phone number, and begin speaking.

Ferrite cores must be attached to the cables to reduce noise. For specific cards, they should be attached as close to the connector as possible, generally within a few centimeters (e.g., 3 cm or 5 cm depending on the card type).

These optional service cards have 100 Ohm terminal resistance. For use in point-to-multi-point connections, the cards must be placed at the end of the bus.

Set the termination switch to 120 Ohm (default) or 75 Ohm, depending on the connector type being used.

No, you can only use one type of connector for the connection of the PRI30 card; RJ45 and BNC cannot be used simultaneously.

Ensure the power supply unit is in the left-most slot and place optional service cards in the available free slots. Tighten all screws to earth the cards securely.

The unit will be powered when correctly connected to an AC outlet. Note that the unit may remain powered even if the power switch is turned OFF.

Yes. You must discharge static electricity before touching it. Do not attempt to use this switch to start the system again if it has already been unplugged after the initial startup, as this will clear your programmed data.

It serves as the overall system programming tool for the PANAIC KX-TDA100, allowing for configuration of intercom and trunk calls, as well as setting basic items like date and time.

Yes, the KX-TDA USB driver must be installed on your PC to facilitate the connection.

Copy the setup file to your PC, double-click to run the installer, and follow the on-screen instructions from the installation wizard.

No, use only the AC power cord included with the PANAIC KX-TDA100 for the power supply unit.

It provides status during startup. Flashing indicates initialization is in progress, and a solid light indicates the system has started successfully.

In some countries or areas, the PRI30 card must not be connected to the public switched telephone network.

A single ferrite core can hold a maximum of 4 cables.

This is expected after performing a system initialization, as the system has been reset to default values.

A WARNING means that misuse could result in death or serious injury. A CAUTION means that misuse could result in injury or damage to property.

It contains the software for all processes of the PANAIC KX-TDA100 and all customer data.

Connect the frame of the PANAIC KX-TDA100 to earth. Proper earthing is crucial to protect against external noise and reduce electrocution risk from lightning strikes.

While the AC cable earth helps against noise and lightning, it may not be enough for full protection. A permanent connection between earth and the dedicated earth terminal of the PANAIC KX-TDA100 must be made.

The AC power cord is the main disconnect device. Ensure the AC outlet is located near the PANAIC KX-TDA100 and is easily accessible.

Ensure you discharge static electricity by touching ground or wearing an earthing strap, and ensure the screws are tightened properly to earth the card.

Connect the optional service cards to the trunk through the NT1. Do not connect them directly to the U interface of the trunk.

The default installer password is 1234.

The pin assignments vary by device type, such as DPT, DSS console, APT, or SLT, and are detailed in the installation instructions provided with the unit.

You can confirm the connection by making a test call to another extension or to an outside party using the established procedure.

Quick Setup in the Maintenance Console allows you to easily configure basic system settings, such as time and date, and prepare the PANAIC KX-TDA100 to receive intercom and trunk calls.