OMRON V680-CA5D01-V2 (01) PDF MANUAL

Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury. Additionally, there may be severe property damage.

No, this product is not designed for use in directly or indirectly detecting human bodies in safety-related applications. Do not use the product as a sensing device for human protection.

Observe the following precautions to ensure safe usage of the product:

1. Do not use the product in environments subject to inflammable, explosive, or corrosive gases.

2. Do not disassemble, repair, or modify the product in any way.

3. Tighten the base mounting screws and terminal block screws securely.

4. Use the specified sizes of crimp terminals for wiring.

5. Always lock the lock mechanisms on any devices provided with them, such as cable connector lock screws.

6. Confirm that the DC power supply is within the rated power supply voltage (24 VDC +10%/-15%) before using it.

7. Do not reverse polarity when connecting the power supply.

8. Do not allow water to enter or insert wire in the gaps of the case. Fire or electric shock may result.

9. Always turn OFF the power supply to the ID Controller before attaching or removing the Antenna and Amplifier section.

10. If you suspect that anything is wrong with the product at any time, stop using it immediately, turn OFF the power supply, and consult with your OMRON representative.

11. When disposing of the product, dispose of it as industrial waste.

This is a class A product. In residential areas it may cause radio interference, in which case the user may be required to take adequate measures to reduce interference.

Do not install the product in the following locations:

• Locations subject to corrosive gases, dust, dirt, metal powder, or salt

• Locations where the specified ambient operating temperature range is exceeded

• Locations subject to extreme temperature changes that may result in condensation

• Locations where the specified ambient operating humidity range is exceeded

• Locations where the product would be directly subjected to vibration or shock exceeding specifications

• Locations subject to contact with water, oil, or chemicals

The product uses the 13.56MHz frequency band to communicate with Tags. Some devices, such as some motors, inverters, and switch mode power supplies, generate electromagnetic waves (i.e., noise) that can affect communications with the Tags. If any of these devices are nearby, communications with Tags may be affected or Data Carriers may be destroyed. If the product is to be used near such devices, check the effects on communications before using the product.

To minimize the general influence of noise, follow the following precautions:

(1) Ground the earth terminal of this product and any metallic material located around the product to 100Ω or less.

(2) Keep product wiring away from high voltage or heavy current.

The product does not provide a water-proof structure. Do not use it where mists are present.

Do not use chemicals that will affect product materials.

Tighten screws to 1.2 N·m when mounting the product.

Communications performance may be reduced due to mutual interference if more than one Read/Write Antenna is installed in the same vicinity. Refer to the Read/Write Antenna and Tag Operation Manual (Cat. No. Z248-E1) and confirm that there is no mutual interference between Read/Write Antennas.

Do not store the product in the following locations:

• Locations subject to corrosive gases, dust, dirt, metal powder, or salt

• Locations where the specified ambient storage temperature range is exceeded

• Locations subject to extreme temperature changes that may result in condensation

• Locations where the specified ambient storage humidity range is exceeded

• Locations where the product would be directly subjected to vibration or shock exceeding specifications

• Locations subject to contact with water, oil, or chemical

Do not use thinners for cleaning. Resin materials and the case coating will be dissolved by thinners, benzenes, acetones and kerosenes.

Use the product connected to one of the following two circuits:

(1) Limited Voltage/Current Circuit (Approved in UL508)

(2) A circuit with a maximum voltage of 30 Vrms (42.4 V peak) that uses as its power supply a Class 2 power supply defined in UL1310 or a Class 2 transformer defined in UL1585.

A circuit that uses as its power supply the secondary coil of an insulated transformer that satisfies the following conditions:

• Maximum voltage (with no-load): 30 Vrms (42.4 V peak) OR

• Maximum current: (1) 8 A (including when shorted) OR

(2) A current restricted by a circuit protective device (e.g., fuse) with the following ratings:

A circuit with a maximum voltage of 30 Vrms (42.4 V peak) that uses as its power supply a Class 2 power supply defined in UL1310 or a Class 2 transformer defined in UL1585.

When mounting directly to a control panel, always use flat washers and M4 screws. Tightening torque: 1.2 N·m.

(1) When mounting the ID Controller to DIN Rail, hook the ID Controller at point A and then press in direction B.

(2) To remove the ID Controller from the DIN Rail, pull out the mounting hook.

Recommended DIN Rail: PFP-100N2 (rail length: 1 m) (manufactured by OMRON).

Note 1: The CPU will stop operation and the RST indicator will light when the RST input is turned ON. The ERROR output will be reset at that time.

Note 2: The transistor may be damaged if an output is shorted with no load connected.

The CPU will stop operation and the RST indicator will light when the RST input is turned ON. The ERROR output will be reset at that time.

The transistor may be damaged if an output is shorted with no load connected.

Note: The specific values for Insulation resistance and Dielectric strength were split in the original table and visually associated. The extracted table above maintains the items, but the PDF shows “20 MΩ (at 500 VDC mega)” for insulation resistance and “1,000VAC 50/60Hz for 1 minute” for dielectric strength associated with these rows.

Dispose in accordance with applicable regulations. When disposing of the product, dispose of it as industrial waste.