NOSTALGIA ELECTRICS VINTAGE CCM600 (01) PDF MANUAL

1. NEVER use a scouring pad on the unit.

2. NEVER leave unit unattended while in use.

3. NEVER place anything other than the intended sugar in the Extractor Head.

4. NEVER pour water or any other liquid into the Extractor Head.

5. NEVER put fingers on or near the Extractor Head or Heating Element while machine is on, nor while it is still hot.

6. Unplug unit from outlet when not in use and when cleaning.

7. DO NOT operate this appliance with a damaged cord or plug or in the event the appliance ever malfunctions.

8. DO NOT put parts in dishwasher for cleaning.

9. DO NOT use outdoors. For indoor use only.

10. This appliance is NOT A TOY.

11. This appliance is not intended for use by young children.

12. Young children should be supervised while product is in use to ensure that they do not play with the appliance.

When using electrical appliances, basic safety precautions should always be followed, including:

13. Read all instructions before operating this appliance.

14. DO NOT TOUCH the hot surfaces.

15. To protect against electrical shock do not immerse cord, plug or any part of this unit in water or other liquids.

16. Close supervision is necessary when any appliance is used by or near children.

17. Unplug from outlet when not in use and before removing parts for cleaning.

18. DO NOT operate any appliance with a damaged cord or plug or if the appliance has been damaged in any manner. Return the appliance to the nearest repair shop for examination or repair.

19. The manufacturer does not recommend the use of accessory attachments. Use of attachments may cause injuries.

20. DO NOT let the cord touch hot surfaces.

21. DO NOT pour water or any other liquid into the Extractor Head.

22. DO NOT place parts on or near a hot gas or electric burner, or in a heated oven.

23. Extreme caution must be used when moving this appliance.

24. This unit must be on a level surface to operate properly.

25. DO NOT use this machine for other than its intended use.

26. DO NOT leave unit unattended while in use or when plugged into an outlet.

27. Check the Extractor Head for foreign objects before switching to ON position.

28. The Extractor Head will get hot. Avoid contact until fully cooled.

29. A short power supply cord is provided to reduce the risk resulting from becoming entangled or tripping over a long cord.

30. Extension cord can be used if care is exercised in use.

31. The marked electrical rating of an extension cord should be at least as great as the electrical rating of the appliance.

32. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock, this plug is intended to fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to modify the plug in any way.

33. Keep hands away from the machine when it is in the ON position and is spinning.

1. Insert Cross Bar (I) into the square inserts on the inside of Base Support (G) and secure from below with two #2 Bolts and two #5 Flat Washers.

2. Insert the Leg Assembly (H) into the square inserts between the ends of the Base Support (G) and fasten from inside with two #4 Bolts, two #6 Flat Washers and two #7 Nut Caps and from the top with two #2 Bolts.

1. Insert #3 Axle Bolt into Base Support (G).

2. Put on #6 Flat Washer. Slide one Wheel (F) into #3 Axle Bolt and add a #5 Flat Washer and a #7 Nut Cap.

3. Use #2 Wrench (L) to tighten the #7 Nut Cap.

4. Insert the second #3 Axle Bolt to the other side of Base Support (G), add #6 Flat Washer, second Wheel (F), another #5 Flat Washer, and #7 Nut Cap to the other side of the #3 Axle Bolt, following the directions above.

5. Use #2 Wrench (L) to tighten the #7 Nut Cap.

1. Assemble Base Support (G) into the bottom of the Main Unit (C) and secure with four #2 Bolts.

2. Push Handle (E) attaches onto the Main Unit (C) using four of the supplied #1 Screws and four #5 Flat Washers. Attach Display Tray (D) to Main Unit (C) using four #1 Screws.

3. Attach Bowl (A) to Main Unit (C) by placing Bowl (A) over collar and turning clockwise. Attach Dome to Bowl using three #10 Screws.

The Fuses are marked under each fuse compartment. Two extra 10 Amp fuses are also included with this unit.

1. Using a flathead screwdriver, push in, turning counter-clockwise.

2. Fuse is then accessible and can be changed. Once changed, push in and turn clockwise to lock fuse into place.

1. Before changing the Extractor Head, make sure that the machine is turned OFF, unplugged, and that the Extractor Head has cooled completely.

2. Use #1 Wrench (K) to remove the center bolt.

3. Use pliers to loosen and remove the red and black wires from the bottom of the Extractor Head.

4. Attach the red and black wires to the new Extractor Head and tighten.

5. Place the new Extractor Head with wires attached onto the shaft and replace center bolt.

6. Tighten the center bolt using the #1 Wrench (K).

The Kryptol is the connection point that powers the heating element on the extractor head. The electricity from the machine transmits heat through the Kryptol which allows the Extractor Head to get hot and melt the sugar. Eventually the Kryptol wears down with continued use of the OLD FASHIONED COMMERCIAL COTTON CANDY MAKER, and needs to be replaced. Follow the directions below when changing the Kryptol:

1. Before replacing the Kryptol, make sure that the machine is turned OFF, unplugged, and the Extractor Head has cooled completely.

2. Use the Screwdriver to remove all screws from the collar and remove collar.

3. Remove Kryptol Housing Cover using (K) Wrench #1.

4. Pull Kryptol out of Housing and replace with new Kryptol.

5. Replace Kryptol Housing cover and tighten with #1 Wrench (K).

6. Repeat steps 3, 4 and 5 with the other Kryptol Housing.

7. Replace Collar and tighten screws using Screwdriver.

1. First, position OLD FASHIONED COMMERCIAL COTTON CANDY MAKER close to an electrical outlet before starting. Make sure the cord is away from any water source. It is acceptable to use an extension cord if needed.

2. Plug in unit at the OFF position.

3. Turn both power switch and heater switch to ON position and allow unit to run for at least 3-5 minutes before adding sugar. This will allow the Extractor Head to heat.

4. Once Extractor Head has heated, turn unit OFF.

5. Place no more than one scoop of sugar (flavored or white, granulated) or up to four pieces of hard candy into the Extractor Head.

6. Switch to ON position.

7. When you see the cotton candy web begin, collect the cotton candy on the cone by holding the cone and rotating the cone with your fingers while you circle the bowl.

8. Repeat above steps by turning off machine and adding another scoop of sugar or four more pieces of hard candy into the Extractor Head. Once you have added sugar or candy, start machine again. The cotton candy should flow more quickly as the unit is sufficiently warm.

9. Never use ingredients other than sugar or hard candy. DO NOT overfill the Extractor Head by adding more than one scoop of sugar or more than four pieces of hard candy at a time. This will cause clogging and unit will not work properly.

10. By following these simple instructions, using your OLD FASHIONED COMMERCIAL COTTON CANDY MAKER will be a fun experience for kids of all ages and will bring the excitement of a carnival to any occasion.

Cotton candy is made by heating sugar. This turns sugar into a liquid form. Then the sugar liquid is forced out of tiny mesh with holes in the extractor head by centrifugal force as the extractor head spins. As the liquid sugar hits the air, it returns to a solid fluffy material that adheres to a paper cone.

It is very important that the unit be cleaned properly after every use. If it is not, the holes will get clogged and sugar will not be able to sift through the tiny holes properly. NEVER put water in the extractor head.

You can clean the Extractor Head by letting the machine run with an empty Extractor Head for five minutes.

If floss does not adhere easily to the cone, you can spray the cone lightly with water.

1. When you have finished making cotton candy, run unit for about five minutes until all sugar has been released through the extractor head.

2. When all remaining sugar is gone, unplug unit and allow to cool down before cleaning.

3. Make sure the unit is unplugged and has had time to cool down before cleaning.

4. Use a clean, slightly damp, non-abrasive sponge or non-abrasive cloth to wipe the outside of the metal extractor head, aluminum Bowl, and inside and outside of plastic Dome, then wipe with a non-abrasive towel to dry.

5. Use a clean, slightly damp, non-abrasive sponge or non-abrasive cloth to wipe down the outside of the Main Unit, then wipe with a non-abrasive towel to dry.

6. NEVER put water in the Extractor Head.