NOKIA AD-42W (01) PDF Document

The NOKIA AD-42W gateway allows you to connect a standard home stereo system to a compatible music player or headset that supports Bluetooth wireless technology.

The gateway is a Bluetooth Class 1 device with an operating range of up to 100 meters (300 feet). However, a typical operating range of Bluetooth devices is 10 meters (30 feet). Connections can be subject to interference from obstructions, such as walls, or other electronic devices.

The gateway contains the following parts:

1. Pairing key

2. Blue indicator light

3. Operating mode key

4. RCA audio inputs (the red connector is for the left stereo channel and the white connector for the right channel)

5. Power connector

6. RCA audio outputs

Check the model number of any charger before use with this device. The device is intended for use when supplied with power from the AC-3, AC-4, or DC-4 charger. Use only chargers approved by Nokia for use with this particular device.

To switch on, plug the charger cable into the power connector at the back, and connect the charger to a wall outlet. When the gateway is connected to a paired audio device and is ready for use, the indicator light flashes slowly. The gateway tries to connect to the Bluetooth device that you have used most recently in the current operating mode.

To switch off, unplug the charger from the wall outlet and the gateway.

To pair the gateway with a music player (such as a music player device or a mobile phone with a music player feature), follow these steps:

1. Check that the operating mode key is in the down position. If it is not, press the key.

2. Press and hold the pairing key until the indicator light is continuously shown.

3. Use your music player or phone to search for and select the gateway and to enter the Bluetooth passcode 0000.

If the pairing was successful, the indicator light flashes quickly 10 times.

To pair the gateway with a headset, follow these steps:

1. Check that the operating mode key is in the up position. If it is not, press the key.

2. Set up the headset for pairing as instructed in the user guide for the headset.

3. Press and hold the pairing key on the gateway until the indicator light is continuously shown.

The gateway is paired automatically with the headset. If the headset requires a Bluetooth passcode and the default passcode of the headset is not 0000, change the passcode to 0000 as instructed in the user guide of the headset.

You can pair the gateway with up to eight Bluetooth devices but connect it to only one device at a time in both operating modes.

To change the Bluetooth audio device (such as a music player or headset) that you have connected to the gateway, disconnect the current device from the gateway and connect another paired device to it.

If you want to clear the list of paired devices, press and hold the pairing key for 15 seconds while you are not listening to music through the gateway.

Ensure that the home stereo system is switched off before making any connections to it. Plug the supplied RCA cables to the audio outputs on the gateway and to the audio inputs on your stereo system. After connecting, set the volume at a moderate level on the music player and the stereo system, and start to play music on the music player.

Ensure that the home stereo system is switched off before making any connections to it. Plug the RCA cables to the audio inputs on the gateway and to the audio outputs on your stereo system. After connecting, set the volume at a moderate level on the headset and the stereo system, and start to play music on the stereo system.

If you have paired and connected the gateway with a music player and a headset, to switch between the two connections, press the operating mode key. To use the gateway with a music player, the operating mode key must be in the down position. To use the gateway with a headset, the operating mode key must be in the up position.

To care for your device:

• Keep all accessories and enhancements out of the reach of small children.

• Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, allow it to dry completely.

• Do not use or store the device in dusty, dirty areas.

• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices and warp or melt certain plastics.

• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.

• Do not attempt to open the device.

• Do not drop, knock, or shake the device.

• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.

• Do not paint the device.