NINJA MEGA KITCHEN SYSTEM BL770 (01) PDF Document

Remove all packaging materials. Exercise care when unpacking blade assemblies, as the blades are sharp. Handle the Chopping and Stacked Blade Assemblies by grasping the top of the shaft. Handle the Nutri Ninja Blade Assembly by grasping around the perimeter of the blade assembly base. Wash containers, lids, and blade assemblies in warm, soapy water using a dishwashing utensil with a handle to avoid direct contact with the blades. Rinse and air-dry all parts thoroughly. Wipe the motor base with a soft cloth and allow it to dry completely before using.

Place the motor base on a clean, dry, level surface. Align and lower the pitcher onto the motor base, with the handle aligned slightly to the right of the LOCK symbol. Rotate the blender pitcher clockwise until it clicks in place. The safety tabs on the bottom of the pitcher will slide under the safety tabs on the top of the motor base.

Once the pitcher is locked onto the base, hold the Stacked Blade Assembly by the top of the shaft and place it onto the drive gear inside the pitcher. Ensure it is seated properly and standing upright. Add your ingredients, ensuring they do not exceed the highest measured marking line.

Hold the lid by the handle in the upright position. Place it on top of the pitcher, aligning the arrow on the lid with the arrow located on the pitcher handle. Press the handle down until you hear a click to lock it in place.

Press the release button on the lid, pull the lid handle up to a 90 degree angle, and lift the lid off the pitcher.

Turn the pitcher counter-clockwise and then lift it off the motor base.

Place the motor base on a flat surface. Add ingredients to the Nutri Ninja cup. Screw the Nutri Ninja Blade Assembly onto the cup tightly until you have a good seal. Turn the cup upside down and place it onto the motor base, aligning the tabs on the cup with the motor base. Turn clockwise to lock into place until you hear a click. Press the power button to turn the unit on, then press the Single Serve button in short intervals to blend.

Once blending is complete, turn the power button off. Turn the Nutri Ninja cup counter-clockwise and pull straight up to remove it from the base. Turn the cup upright and twist the blade assembly counter-clockwise to remove it.

Place the motor base on a flat, clean surface. Align and lower the bowl onto the motor base, with the handle aligned slightly to the right of the LOCK symbol. Rotate the bowl clockwise to lock into place until you hear a click.

Hold the desired blade assembly by the top of the shaft and place it onto the drive gear inside the bowl. Ensure the blade assembly is seated properly and is standing upright before adding ingredients.

Holding the lid by the handle in the upright position, place it on top of the bowl, aligning the arrow on the lid with the arrow located on the bowl handle. Press the handle down until you hear a click.

Open the drizzle hole on the top of the lid and pour the liquid slowly into the mixture.

To remove the lid, press the release button on the lid and pull the lid handle up to a 90 degree angle. To remove the bowl, turn it counter-clockwise and lift it off the motor base.

The unit features a thermal switch that temporarily disables the motor if it overheats. Unplug the unit from the electrical outlet and allow it to cool for approximately 15 minutes. Remove the container lid and blade assembly, then empty the container and ensure no ingredients are jamming the blade assembly. Ensure maximum capacities are not exceeded, as this is the most common cause of overload.

Wash blade assemblies in warm, soapy water using a dishwashing utensil with a handle to avoid direct contact with the blades. Always exercise caution, as the blades are sharp.

Yes, all attachments are dishwasher safe. It is recommended that lids, containers, and blade assemblies be placed on the top rack of the dishwasher only. Ensure blade assemblies are removed from their containers before placing them in the dishwasher.

Turn off the unit and unplug the motor base before cleaning. Wipe the motor base with a clean, damp cloth. Do not use abrasive cloths, pads, or brushes to clean the base.

Wrap the power cord around the cord wrap on the back of the motor base. Store the unit upright and store all blade assemblies inside or attached to their respective containers with their lids locked in place.

Use Speed Setting 1 with the Dough Blade Assembly in the bowl.

Use the Stacked Blade Assembly (in the pitcher) or Nutri Ninja Blade Assembly (in the cup) on Speed Setting 3 or Single Serve. Ensure sauces and soups are cooled to room temperature before blending.

Use Speed Setting 2 with the Chopping Blade Assembly in the bowl.

For best results, use short pulses.

As a safety feature, the power button will flash and the motor will not work if the pitcher, bowl, or cup and lid are not installed correctly. When they are installed properly, the power button will be solid, indicating that the appliance is ready for use.

No, do not add ingredients before completing installation of the blade assembly.

Ensure the container is securely locked on the motor base. Ensure the lid is securely on the container in the correct position by aligning the arrows. Ensure the power button is turned on. Check that the plug is securely inserted into the electrical outlet and check the fuse or circuit breaker. If the unit has overheated or overloaded, unplug it and wait approximately 15 minutes before using again. Make sure the unit is not overloaded.

Either you are chopping too much food at one time, or the pieces are not of even size. Try processing smaller amounts per batch.

The food has been over processed. Use the pulse button for controlled processing.

The mixture is too thick. Add more liquid to the container.

Do not use ice that has been sitting out or has started to melt. Use ice straight from the freezer. Start with a few pulses and then go to a continuous blending cycle.

Make sure the surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces and will not stick on surfaces such as wood, tile, or non-polished finishes. Do not attempt to use the appliance when the motor base is stuck to a surface that is not secure.

Extension cords should not be used with this appliance.

No, do not blend hot liquids. Doing so may result in pressure buildup and steam exposure that can pose a risk of the user being burned.

Yes, ensure the blade assembly is removed before emptying the container’s contents. Remove the blade assembly by carefully grasping the top of the shaft and lifting it from the container. Failure to do so results in a risk of laceration.

No, the blade assemblies are designed to be removable to facilitate cleaning and replacement. They are not locked in place in their containers.

No, do not fill containers past the MAX FILL or MAX LIQUID lines.

Stop the appliance, remove the blade assembly, and use a scraper to dislodge ingredients.

No, do not open the pitcher’s pour spout cap while the blender is operating.

Never insert your hands into the pitcher, as you may contact one of the blades and experience a laceration. Stop the appliance, remove the lid, and use a spatula to dislodge ingredients.

No, do not attempt to remove the container or lid from the motor base while the blade assembly is still spinning. Allow the appliance to come to a complete stop before removing lids and containers.

No, do not store ingredients before or after blending them in the cup with the blade assembly attached. Some foods may contain active ingredients or release gases that will expand if left in a sealed container, resulting in excessive pressure buildup. For storage, use only the Spout Lid to cover.

Place your hands underneath both sides of the motor base and gently pull the unit up and towards you.

The unit is intended to create a dough ball. It is not intended to continuously knead. After the dough ball forms, additional kneading should be done by hand on a work surface.

No, do not microwave any containers or accessories provided with the appliance.

No, the blade assemblies are not interchangeable.

Exercise extreme care and always grasp the blade assemblies by the top of the shaft or the outer perimeter of the base, as the blades are sharp.

Before each use, inspect blade assemblies for damage. If a blade is bent or damage is suspected, stop using it.

No, do not operate the appliance with an empty container.

No, never leave the appliance unattended while in use.

No, do not process dry ingredients with the Single-Serve Blending Cup, the pitcher with the Stacked Blade Assembly, or the processor bowl with the Chopping Blade Assembly.

When using the processor, always use the food pusher to add food. Never add food by hand.

No, do not attempt to sharpen blades.

If the unit moves excessively on the work surface, remove the dough ball and knead by hand.

Be sure to store the Nutri Ninja Blade Assembly attached to an empty cup when not in use.

Yes, you can use the Stacked Blade Assembly in the pitcher or the Nutri Ninja Blade Assembly in the cup on Speed Setting 3 or Single Serve to crush ice.

No, Ninja containers are not intended for hot blending.

The maximum liquid capacity for the pitcher is 64 oz. (8 cups, 1.9 L).

The capacity of the food processor bowl is 64 oz. (8 cups, 1.8 L).

Unplug the unit from the electrical outlet. Allow it to cool for approximately 15 minutes. Remove the lid and blade assembly, empty the container, and ensure no ingredients are jamming the blades.

Yes, always wait for the appliance to come to a complete stop before removing the lid and container.

Do not overfill the cup. To avoid spilling, do not add ingredients past the MAX fill line.