NEXIGO PJ30 (01) PDF Document

The following child safety measures must be observed:

• Children should not play with this appliance. Cleaning and user maintenance should not be made without direct supervision by an adult.
• Children less than 3 years of age should be kept away from this device unless continuously supervised.
• Children from 3 to 8 years of age should not plug in, regulate, clean, or perform any type of maintenance on this device.
• Children from 3 to 8 years of age shall only switch the appliance on/off after all the following safety precautions have been met:
  • The product has been placed or installed in its intended operating position.
  • The child has direct supervision or has been given full instructions on how to use the device safely.
  • The child is capable of understanding the hazards involved.

• For appliances having a specially prepared cord, if the supply cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
• To ensure the projector is operating smoothly and is protected from any potential overheating issues, make sure to install the projector in a location that does not block ventilation.
• To reduce the risk of fire and/or electric shock, do not expose the projector to moisture or liquids.
• Do not install the projector near heat sources or any other appliance that emits heat.
• Do not allow small objects to enter the projector. They may cause the projector to short circuit, which could start a fire or create an electric shock.
• Do not use the projector under the following conditions:
  • In extremely hot, cold, or humid environments. Ensure that the ambient room temperature is within ~5°C – ~35°C and relative humidity is ~30% – ~90%.
  • In areas susceptible to excessive dust and dirt.
  • Near any appliance generating a strong magnetic field.
  • In direct sunlight.
• Do not use the projector if it has been physically damaged or abused. Physical damage/abuse could include: the projector has been dropped, the power supply cord or plug has been damaged, liquid has been spilled onto/into the projector, the projector has been exposed to rain or moisture, or something has fallen into the projector/is loose inside.
• Do not place the projector on an unstable surface. The projector may fall over, resulting in injury or damage to the unit.
• Do not block the light coming out of the projector lens when in operation. Objects in the light’s path may melt, cause burns, or start a fire.
• Please do not open or disassemble the projector, as this may result in an electrical shock.
• Do not attempt to service the unit yourself. Opening the unit may expose you to dangerous voltages and/or other hazards. The unit should only be repaired by the manufacturer or its service agent.
• Only use attachments/accessories directly specified by the manufacturer.
• Do not look straight into the projector lens during operation. Excessively bright lighting has been shown to harm vision under some circumstances.
• When switching the projector off, please ensure the cooling cycle has been completed before disconnecting the power. Allow at least 90 seconds for the projector to cool down.
• Do not use a power source with a voltage other than what is specified in this manual.
• Disconnect the power plug from the AC outlet if the product is not being used for a long period of time.
• Do not set up the projector in areas where it might be subjected to vibration or shock.
• Do not touch the lens with your bare hands.
• Remove the battery/batteries from the remote control before storage. If the battery/batteries are left in the remote for a long period of time, they may leak.
• Do not use or store the projector in places where smoke may be present, as it can negatively affect the quality of the projector’s performance.
• Use a power strip and/or surge protector with this device. Power outages and/or brownouts can damage your device.
• When installing or adjusting a ceiling or wall mount, do not use adhesives, oils, and/or lubricants. These may cause the projector case to crack and allow it to fall from its ceiling mount.
• Do not stand the projector vertically. Doing so may cause the projector to fall over, causing damage and/or injury.

• Turn off the projector and unplug the power plug from the AC outlet before cleaning the unit.
• Use a soft, dry cloth with mild detergent to clean the product housing. Do not use harsh cleaners, waxes, or solvents to clean the unit.

• 15-20 minutes before cleaning the lens, turn off the projector and unplug the power cord to allow the lens to cool down completely. Failure to do so may cause damage to the lens that is not covered by warranty.
• Use compressed air to remove dust from the surfaces of the projector.
• Use a microfiber cloth for cleaning and make sure to wipe the lens gently. Do not touch the lens with your fingers.
• Do not use detergents or solvents such as alcohol to clean the lens, only use water as a cleaning agent. Damaging the lens during cleaning is not covered under warranty.
• Do not wipe or tap the lens with a hard object.

• Power Switch: Toggles power on and off.
• Mute: Toggles audio on and off.
• Focus Out: Pushes the focal point further away.
• Focus In: Pushes the focal point closer in.
• Left/Right/Up/Down: Moves the cursor in the on-screen display.
• OK: Selects the option your cursor is currently on.
• Return: Returns to the last screen.
• Input (Short Press): Displays the source selection bar.
• Menu (Long Press): Displays the menu.
• Vol +: Increases the volume level.
• Vol -: Decreases the volume level.

• 1 x Projector
• 1 x Cleaning Kit
• 1 x Remote (Requires 2 AAA batteries, not included)
• 1 x Power Cable
• 1 x AV Cable
• 1 x User Manual

Consider the following when selecting a location:

• The size, shape, and position of your screen.
• Location of a suitable power outlet.
• Ensure the projector has sufficient room around it for airflow.

The projector is designed to be installed in one of four layouts: Ceiling mount (front projection), Ceiling mount (rear projection), Desktop mount (front projection), or Desktop mount (rear projection). You may need to change the projection mode under the Setting tab so images project correctly.

For ceiling mounting:

1. Please remove the 4 feet at corners on the bottom of the projector for mounting on the ceiling.
2. The projector’s mounting holes are M4 x 9.7mm in size. The distance between these mounting holes on the back of the projector measures 11.7″ diagonally, 10.3″ horizontally, and 6.2″ vertically. You could find a suitable ceiling mount based on these specifications.

Note: Due to manufacturing tolerances there will be variances of about 3% from unit to unit. Please use actual measurements when installing the device.

Keystone correction adjusts the image of a projector that is displaying an angled image (trapezoid shape). To correct this, please use the Keystone Adjustment knob to adjust the vertical keystone if the projection image shows up tilted.

There are two ways to adjust the focus:

Option 1 – Remote Control: Press and hold one of the focus buttons on the remote until the image is clear. If the image does not clear and instead becomes more fuzzy, press and hold the other focus button until the image clears up.

Option 2 – On-Screen Menu: In the menu go to the Setting tab, select Focusing, and then press and hold the Left/Right button on the projector panel (or Left/Right button on the remote) until the image is clear. If the image does not clear and instead becomes more fuzzy, press and hold the other button until the image clears up.

Insert a USB drive into either of the USB ports. In the on-screen menu select the Multi-media tab. Then choose the content which you want to display: Movie, Music, Photo, Text.

Supported Formats:

Plug an HDMI cable into the device you want to connect to the projector and then insert the other end of the HDMI cable into either of the HDMI ports. Open the on-screen menu and select the correct HDMI source (HDMI1 or HDMI2) in the Input Source tab.

Supported Resolutions:

In order to use a device with a standard RCA connection you will need to obtain an RCA to 3.5 mm adapter. Connect the adapter to the projector, and then connect the RCA plugs from the device to the RCA jacks on the adapter. You can also just use a singular AV cable if this is an option for your device. Once connected, go into the on-screen menu and select AV under Input Source.

Headphones or speakers could be connected to the projector with the 3.5mm audio jack.

You can wirelessly connect your iPhone, iPad, MacBook, computer, or a wide range of other devices to the projector. For wireless connections: Ensure the projector and your device are connected to the same network. Instructions on how to connect the projector to a network are available in the Setting Menu section.

Once both devices are connected to the same network, in the on-screen menu select the Input Source tab, and then select MultiScreen to connect to the screencast software. Then select the corresponding MultiScreen connection option.

To connect, make sure both devices are connected to the same network, your computer is Windows 10 or above and has built-in dual-band WiFi. On the projector, select Windows Cast from the options. On your computer, input Windows key + K to open the Connect sidebar for Miracast, and then select “NexiGo-PJ30” in the devices list. The connection is now complete.

This is only available on iPhone and iPad devices. Plug your iPhone or iPad into the USB port (Screen Monitor). On the projector, select iOS Cable Cast from the options. Tap Trust when the phone/tablet shows a message saying “trust this device”, and then enter the device password to finish the connection.

To connect, make sure both devices are connected to the same network. On the projector, select Miracast from the options. Enter into the System Settings on the Android device and then search for the cast software for your device. Once you have opened the cast software for your device, look at the list of available mirroring devices and select “NexiGo-PJ30” from the list.

Note: Android devices may have mixed functionality with Miracast. OnePlus/Google Pixel – Search Cast, Samsung – Search Smart View, Sony – Search Screen Mirroring.

To connect, make sure both devices are connected to the same network. On the projector, select iOS Cast from the options. Enter into the control center on the iOS device, click Screen Mirroring. In the list of available mirroring devices, select the device “NexiGo-PJ30” from the list.

To connect with DLNA, ensure that both devices are connected to the same network. On the projector, select DLNA from the options. On the device you want to cast from, open an app that supports casting (e.g., YouTube), and then tap the button on the app that allows you to cast. Select “NexiGo-PJ30” from the list of options. Press the play button on the video, and it will now display the video via the projector.

• WiFi Setting: Setup the WiFi connection for the projector.
• Online Update: Update the projector software version online. Ensure the projector is connected to the network. Move the on-screen cursor to Online Update and press OK. A firmware upgrade confirmation window will pop up, click confirm to start the update.
• Restore Factory Default: Reset the cast software to factory default. (Clears the WiFi password and/or caches.)
• Software Version: Shows the current casting firmware version.

• Projection Mode: To shift the mode of the projector. Options are: standard, mirrored, flipped, and flipped and mirrored.
• Image Scaling: Changes the size of the objects shown on the screen.
• Aspect Ratio: Common aspect ratios are 4:3 and 16:9.
• Picture Mode: Adjust color, brightness, contrast, and/or sharpness. Note: This adjustment only impacts the picture parameters of the HDMI input source, excluding the Home page.
• Focusing: Adjust the focus of the projector.

• OSD Language: Choose the language used in the projector menus.
• Software Update: Update the projector software version. Download firmware to a USB drive, insert into the projector, select Setting > System Setting > Software Update.
• Restore Factory Setting: Reset the projector to factory default.
• Auto Sleep: Allows you to set a timer to turn the projector power off automatically.

In the on-screen menu, select Setting, and then scroll down until you see the option labeled WiFi Setting. Select that option. Select your wireless network from the list to connect your projector to the WiFi network.

1. In the on-screen menu, select Setting, and then scroll down until you see the option labeled Bluetooth. Select that option.
2. Turn on Bluetooth for the projector, as well as on the device you would like to connect to, and then search the list for the Bluetooth audio device to connect.
3. Select that device and pair the two devices.

Clean the air filter every month:

1. Turn off the projector and unplug the power adapter.
2. Place the projector bottom-up, push down the air filter cover to pop up the air filter. Take the air filter out of the projector.
3. Gently remove the dust using a small vacuum designed for computers or a soft brush (such as a paintbrush). Note: Do not rinse the air filter in water, or use any detergent or solvent.
4. Place the air filter back in the projector. Push it down and hold until it clicks into place.

• If your projector begins to smoke, make unusual noises, or any strange odor is noticed, immediately unplug your projector.
• Do not look into the lens when the projector is operational.
• Do not turn off the main power abruptly or unplug the projector during operation. Wait until the fan has turned off before powering off fully.
• Do not attempt to use the projector in a vertical orientation.
• Place the projector within a slope of ±15°. Any greater slope presents dangers of the unit sliding and falling.
• Avoid obstructions around the projector air vent.
• Safe Operational Parameters:
  • Operating temperature: between +41°F (+5°C) and +95°F (+35°C)
  • Operating humidity: between 30 and 90%