NETGEAR GS305PV2 (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD NETGEAR GS305PV2 (01) PDF MANUAL


PDF Content Summary: Installation Guide 5-Port Gigabit Ethernet PoE+ Unmanaged Switch GS305Pv2 (63W) 5-Port Gigabit Ethernet PoE+ Unmanaged Switch GS305PP (83W) 1. Register with the NETGEAR Insight app 1. Search for NETGEAR Insight and download the latest app. 2. Set up a NETGEAR account if you do not have one. 3. Tap the menu in the upper-left corner. 4. Tap REGISTER ANY NETGEAR DEVICE. 5. Use the camera on your mobile device to scan the serial number bar code, or enter the serial number located on the bottom of the switch. 6. Tap GO. The switch is registered and added to your account. You can now view the switch in the NETGEAR Insight app. Note: Because this is an unmanaged switch, you cannot configure or manage it in NETGEAR Insight. 2. Connect the switch This switch is designed for indoor use only. If you want to connect it to a device located outdoors, the outdoor device must be properly grounded and surge protected, and you must install an Ethernet surge protector inline between the switch and the outdoor device. Failure to do so can damage the switch. Before connecting this switch to outdoor cables or devices, see kb.netgear.com/000057103 for safety and warning information. 3. Check the LEDs When you connect the power adapter to the switch and plug it into an electrical outlet, the LEDs indicate the status. The GS305Pv2 and GS305PP provide PoE+ or PoE power on ports 1–4 up to 30W PoE to each port, with a PoE power budget of 63W and 83W respective to each model across all active PoE ports. LED Description Power On. The switch is receiving power. Off. The switch is not receiving power.

Package contents • Switch model GS305Pv2 or GS305PP • DC power adapter Access point Sample connections GS305PP Internet PoE+ Router Internet Ports 1–5 left port Ports 1–4 right port On.1000 Mbps link on this port. On. 100 Mbps or 10 Mbps link on this port. Blinking. 1000 Mbps activity on this port. Blinking. 100 Mbps or 10 Mbps activity on this port. Off. No link is detected on this port. On. PoE is in use. On. PoE fault. Off. PoE is not in use on this port.

• Detachable power cable (varies by region) • Wall-mount kit screws • Four rubber footpads • Installation guide Note: We recommend that you use Category 5e (Cat 5e) cable or higher for Gigabit Ethernet connections. VoIP phone Security cameras PoE Max The PoE Max LED indicates the status of the PoE budget on the switch: Off. Sufficient. More than 7W of PoE power is available. On. Less than 7W of PoE power is available. Blinking. At least once during the previous two minutes, less than 7W of PoE power was available. PoE considerations The PoE and PoE+ power supplied by the switch is prioritized in ascending port order (from port 1 to port 4), with a total power budget of 63W for the GS305Pv2, and 83W for the GS305PP switch. If the power requirements for the attached powered devices (PDs) exceed the total power budget of the switch, the PD on the highest-numbered port is disabled to make sure that the PDs that are connected to the higher-priority, lower-numbered ports are supported first. Just because a PD is listed as an 802.3at PoE powered device does not necessarily mean that it requires the maximum power limit of the specification. Many PDs require less power, potentially allowing all four PoE ports to be active simultaneously. You can override the detected device class and specify the power allocation for the device connected to each port. The following table shows the standard PoE troubleshooting Here are some tips for correcting PoE problems that might occur: • If the PoE Max LED is yellow, disconnect one or more PoE devices to prevent PoE oversubscription. Start by disconnecting the device from the highest numbered port. • For each powered device (PD) that is connected to the switch, the associated right port LED on the switch lights solid green. If the right port LED lights yellow, a PoE fault occurred because of one of the conditions listed in the following table. PoE Fault Condition Possible Solution A PoE-related short circuit occurred on the port. The problem is most likely with Support and Community Visit netgear.com/support to get your questions answered and access the latest downloads. You can also check out our NETGEAR Community for helpful advice at community.netgear.com. Regulatory and Legal Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français canadien à netgear.com/support/download/. (If this product is sold in Canada, you can access this document in Canadian French at netgear.com/support/download/.)

power ranges with no overrides applied, and calculated with the maximum cable length of 328 feet (100 meters). The PoE power demand of the PD exceeded the maximum level that the switch permits. The maximum level is 15.4 for a PoE connection or the attached PD. Check the condition of the PD or restart the PD by disconnecting and For regulatory compliance information including the EU Declaration of Conformity, visit netgear.com/about/regulatory/.

Device Class Standard Class Description Power Reserved by the Device Power Delivered to the Device 30W for a PoE+ connection The PoE current on the port exceeded the reconnecting the PD. See the regulatory compliance document before connecting the power supply. For NETGEAR’s Privacy Policy, visit netgear.com/about/privacy-policy.

0 PoE and PoE+ Default power (full) 15.4W 0.44W–12.95W 1 PoE and PoE+ Very low power 4.0W 0.44W–3.84W 2 PoE and PoE+ Low power 7.0W 3.84W–6.49W 3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W 4 PoE+ only High power 30.0W 12.95W–25.5W classification limit of the PD. The PoE voltage of the port is outside the range that the switch permits Mount the switch on a wall Restart the switch to see if the condition resolves itself. By using this device, you are agreeing to NETGEAR’s Terms and Conditions at netgear.com/about/terms-and-conditions. If you do not agree, return the device to your place of purchase within your return period. Do not use this device outdoors. The PoE source is intended for intra building connection only. If a device receives insufficient PoE power from the switch, consider attaching a shorter cable. June 2020 © NETGEAR, Inc., NETGEAR and the NETGEAR Logo are trademarks of NETGEAR, Inc. Any non‑NETGEAR trademarks are used for reference purposes only. We recommend that you use the wall-mount screws that came with the switch. 1. Locate the two mounting holes on the bottom panel of the switch. 2. Mark and drill two mounting holes in the wall. 3. The two mounting holes must be 1.53 in. (38.9 mm) apart, center-to-center. Insert the supplied anchors into the wall and tighten the screws with a No. 2 Phillips screwdriver. Leave about 0.125 in. (4 mm) of each screw protruding from the wall so that you can insert the screws into the holes on the bottom panel. Note: GS305PP screws are 4.2 mm in diameter, 25 mm in length. NETGEAR, Inc. 350 East Plumeria Drive San Jose, CA 95134, USA NETGEAR INTERNATIONAL LTD Floor 1, Building 3, University Technology Centre Curraheen Road, Cork, T12EF21, Ireland


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply