NANLITE FS-150B (01) PDF Document

The technical data for the NANLITE FS-150B, FS-200B, and FS-300B models are as follows:

The main parts of the NANLITE FS-150B and their functions are:

1. Lock catch: For installing and disassembling the reflector and other accessories.

2. Umbrella hole: For installing/removing an umbrella.

3. Reflector: For gathering light to improve central illumination.

4. Angle fixing knob: Allows for adjusting and fixing the illumination direction.

5. LCD screen: For displaying the data.

6. Lamp body handle: Convenient for users to lift the lamp and adjust its direction.

7. USB port: For updating the firmware.

8. Right knob: For selecting options and adjusting the color temperature under CCT mode.

9. MODE button: For switching between CCT mode, EFFECT mode, and MENU.

10. Power switch: For switching the fixture on/off.

11. Fuse base: For placing the fuse.

12. Left knob: For adjusting the DIM (brightness) and scrolling through different selections.

13. Power socket: AC power input socket.

14. Yoke: Designed for connecting the lamp to a light stand and adjusting the direction of light.

15. Bracket fixing knob: For locking the light fixture to a stand and adjusting the horizontal direction of light.

To install the reflector on your NANLITE FS-150B:

1. Ensure the mounting points on the reflector align with the slots on the light fixture.

2. Once aligned, push the reflector into place.

3. Rotate the reflector in the direction shown on the light until it clicks into place.

To remove the reflector from your NANLITE FS-150B:

1. Press and hold the lock catch to release the reflector.

2. Rotate the reflector until it is free to be removed from the fixture.

To install an umbrella on your NANLITE FS-150B, follow these steps:

1. Loosen the angle fixing knob.

2. Put the umbrella shaft into the umbrella hole.

3. Tighten the angle fixing knob to lock the umbrella in place.

The NANLITE FS-150B can be remotely controlled and supports 2.4G wireless protocols V1.0 and V2.0. To set the protocol:

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” until you reach the WIRELESS PROTOCOL setting.

3. The current setting (e.g., WIRELESS PR: V1.0) will be displayed.

4. Rotate the “left knob” to select either V1.0 or V2.0 based on your remote controller.

Note: The fixture should be set to V2.0 when using a WS-RC-C1 or WS-RC-C2 remote controller, and to V1.0 when using other remote controllers.

1. Ensure the power cable is securely connected and the power switch is off.

2. Turn on the power switch. The LCD screen will turn on and display the fixture’s information.

3. Press the MODE button until the screen indicates you are in CCT mode.

4. To adjust brightness (DIM), rotate the “left knob”. The range is from 000% to 100%.

5. To adjust color temperature (CCT), rotate the “right knob”. The range is from 2700K to 6500K.

Yes. When the fixture controls are unlocked, you can press the “left knob” in any mode to turn off the light. The brightness percentage on the screen will show 000%. Press the “left knob” again to restore the light to its previous state. You can press continuously to switch between on and off.

The NANLITE FS-150B has several built-in special effects. To access them:

1. Press the MODE button to switch to EFFECT mode.

2. The screen will display the current effect (FX). Rotate the “left knob” to cycle through and select the desired effect.

The available effects are:

• CCT LOOP

• INT LOOP

• FLASH

• PULSE

• STORM

• TV

• PAPARAZZI

• CANDLE/FIRE

• BAD BULB

• FIREWORK

• EXPLOSION

• WELDING

After selecting a special effect in EFFECT mode, you can adjust its parameters:

1. Rotate the “right knob” to select which parameter to adjust (e.g., DIM, CCT, SPD).

2. Rotate the “left knob” to change the value of the selected parameter.

The adjustable parameters for each effect are:

• CCT LOOP: DIM, CCT, SPD (Speed, 02S-30S)

• INT LOOP: DIM, CCT, SPD (Speed, 02S-30S)

• FLASH: DIM, CCT, INTERVALS (0.1S-10S)

• PULSE: DIM, CCT, PULSES/MIN (001-240)

• STORM: DIM, CCT, INTVL (Interval, 1s-60s)

• TV: DIM, CCT, SPD (Speed, 001-100)

• PAPARAZZI: DIM, CCT, SPD (Speed, 001-100)

• CANDLE/FIRE: DIM, CCT, SPD (Speed, 001-100)

• BAD BULB: DIM, CCT, SPD (Speed, 001-100)

• FIREWORK: DIM, CCT, SPD (Speed, 001-100), DECAY (001-100)

• EXPLOSION: DIM, CCT, SPD (Speed, 001-100), DECAY (001-100)

• WELDING: DIM, CCT, SPD (Speed, 001-100), PAUSE (ON/OFF)

To access and navigate the MENU:

1. Press the MODE button to enter the MENU interface.

2. Press the “right knob” to cycle through and select from the available menu options.

The menu options include: CH, OUTPUT MODE, BLUETOOTH, WIRELESS PROTOCOL, FAN, FIRMWARE UPDATE, LANGUAGE, and VERSION.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select OUTPUT MODE.

3. Rotate the “left knob” to select between MAX or CONSTANT output modes.

1. Press the MODE button to switch to the MENU.

2. Rotate the “right knob” until BT: RESET is selected.

3. Press the “right knob” to enter the bluetooth reset interface.

4. The options BACK and RESET will be displayed. Rotate the “right knob” to select RESET.

5. Press the “right knob” to confirm the reset. The fixture will return to the menu after the bluetooth reset is complete.

To control the fan:

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to the FAN setting.

3. Rotate the “left knob” to select ON or OFF.

Note:

• When the fan is turned ON, the maximum output of the light will be 100%.

• When the fan is turned OFF, the maximum output of the FS-150B and FS-200B is 15%, while the maximum output of the FS-300B is 25%.

1. Insert a USB flash drive with the latest firmware into the fixture’s USB port.

2. Press the MODE button to enter the MENU.

3. Rotate the “right knob” to select FW UPDATE.

4. Press the “right knob” to enter the firmware update interface. The fixture will search for the firmware file (e.g., FOUND FIRMWARE V1.02.08).

5. Rotate the “right knob” to select UPDATE.

6. Press the “right knob” to confirm the update. The screen will show “FIRMWARE UPDATED” after the process is completed.

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select LANGUAGE.

3. Rotate the “left knob” to select between English and Chinese (中文).

1. Press the MODE button to enter the MENU.

2. Rotate the “right knob” to select VERSION.

3. The firmware version (e.g., V0.01.06) will be displayed on the screen.

To prevent accidental changes, you can lock the controls. Long press the “right knob” to lock all functions. A lock icon will appear on the screen. The current status cannot be changed by rotating the knobs while it is locked. To unlock, long press the “right knob” again to release the lock status.

The package for the NANLITE FS-150B includes the following items:

• Light Fixture x 1

• Power Cable 4.5M x 1

• Reflector x 1

• COB Protective Cap x 1

• User Manual x 1

1. After opening the package, check for any possible damage caused in transit. Do not use the light if damage is found and contact your distributor or the manufacturer.

2. Do not use a power cable with damaged insulation. Do not unplug the cable too hard or drag it directly.

3. Ensure the voltage of the power supply matches the voltage specified on the fixture before installation.

4. Turn the fixture off when it is not in use or before cleaning.

5. Keep the fixture safely stored and away from children.

1. Please remove the COB protective cap before using the fixture.

2. Do not look directly at the emitter when the fixture is on.

3. If you change parameter settings, wait for 10 seconds before turning off the fixture to save the settings.

4. Do not place any object on the fixture or allow liquid to flow inside it.

5. Do not place the fixture near flammable or volatile substances like alcohol or gasoline.

6. Do not use strong detergent for cleaning. Wipe off dirt using a cloth with a neutral cleanser.

7. Set up the fixture in a dry, well-ventilated place. Do not use it in a humid, dusty, or overheated environment and ensure the fan and vent are unimpeded.

8. Do not disassemble the fixture yourself. Maintenance should be conducted by qualified professionals following the procedures in the manual.

9. Do not cover the vents when in use to avoid affecting heat dissipation. Be aware of anti-scald precautions as the fixture’s surface temperature can become high during long-term use.

If you are experiencing issues with your NANLITE FS-150B, please refer to the following fault detection and diagnosis table:

If the failure is not resolved after troubleshooting, please contact the place of purchase or the manufacturer.