MSI MPG GUNGNIR 100D (01) PDF Document

Free English MSI MPG GUNGNIR 100D (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD MSI MPG GUNGNIR 100D (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What are the dimensions (Length, Width, Height) of the MSI MPG GUNGNIR 100D case?

The dimensions for the MSI MPG GUNGNIR 100D case are:

Length: 510mm
Width: 227mm
Height: 525mm

What is the maximum GPU Length supported by the MSI MPG GUNGNIR 100D case?

The maximum GPU Length supported by the MSI MPG GUNGNIR 100D case is 400mm.

What is the maximum CPU Height supported by the MSI MPG GUNGNIR 100D case?

The maximum CPU Height supported by the MSI MPG GUNGNIR 100D case is 170mm.

What is the maximum PSU Length supported by the MSI MPG GUNGNIR 100D case?

The maximum PSU Length supported by the MSI MPG GUNGNIR 100D case is 200mm.

What are the available fan locations and sizes for the MSI MPG GUNGNIR 100D case?

The fan locations and sizes for the MSI MPG GUNGNIR 100D case are:

Front: 3x120mm or 3x140mm
Top: 3x120mm or 2x140mm
Rear: 1x120mm or 1x140mm

What are the compatible radiator sizes for the MSI MPG GUNGNIR 100D case?

The compatible radiator sizes for the MSI MPG GUNGNIR 100D case are:

Front: 360mm or 420mm
Top: 360mm or 240mm
Rear: 120mm or 140mm

How do I remove the front Bezel on the MSI MPG GUNGNIR 100D case?

To remove the front Bezel, it shows an illustration of pulling the panel away from the main chassis. Note that for the GUNGNIR 100 model only, keeping pressing the LED/RESET button for three seconds allows users to control lighting effects via syncing with the motherboard by MSI mystic light app. This specific instruction about the LED/RESET button is noted as being for GUNGNIR 100 only.

What should I refer to when installing the Front I/O Connectors on the MSI MPG GUNGNIR 100D case?

Please refer to your motherboard user’s manual to install the front panel I/O. The drawings provided in the documentation are for reference only.

How should the LED/Reset cables be connected for the MSI MPG GUNGNIR 100D case?

For LED Function, connect the LED/Reset cable to the MSI ARGB Hub. For Reset Function, connect the LED/Reset cable on the Motherboard reset pinheader.

If connected to the MSI ARGB controller, the front panel can switch lighting effects. If connected to the motherboard Reset pin, it performs a regular Reset function.

What items are included in the Accessory Kit Contents for the MSI MPG GUNGNIR 100D case?

The accessory kit contents for the MSI MPG GUNGNIR 100D case include:

Item	Description	Quantity
Long Fan Screws/ 30 mm	(Not included for MPG GUNGNIR 100D / 100P Only is incorrect based on the table layout, the screws are listed generally for the series. The table shows ‘MPG GUNGNIR 100D / 100P Only’ next to Long Fan Screws)	x 12
Motherboard Screws/ 6.5mm		x 21
HDD Screws/ 6.5mm		x 8
PSU Screws/ 9mm		x 4
Cable Ties		x 6

Based on the table presentation, Long Fan Screws/30 mm are specifically listed as “MPG GUNGNIR 100D / 100P Only”.

What are the key features of the MSI MPG GUNGNIR 100D case identified by letters A through G?

The case features for the MSI MPG GUNGNIR 100D are:

A: Tempered Glass Side Panel
B: Dust Filter
C: Solid Side Panel
D: Customize Logo Panel
E: Front Bezel
F: Removable SSD Trays
G: HDD Cages and Trays

How is a Hard Disk Drive (HDD) installed in the MSI MPG GUNGNIR 100D case?

The installation involves mounting the HDD into a drive bay or tray inside the case and connecting the necessary SATA power and data cables to the back of the drive, as illustrated.

How is a Solid State Drive (SSD) installed in the MSI MPG GUNGNIR 100D case?

The installation involves mounting the SSD onto the designated mounting points (often removable trays labeled F) inside the case and connecting the necessary SATA power and data cables to the drive, as illustrated.

Where is the Power Supply Unit (PSU) installed in the MSI MPG GUNGNIR 100D case?

The Power Supply Unit (PSU) is installed in the bottom section of the chassis, as indicated by the illustration showing the PSU being placed into the compartment.

What is the procedure for installing a PCI-e card in the MSI MPG GUNGNIR 100D case?

The procedure for PCI-e Installation in the MSI MPG GUNGNIR 100D case involves several steps:

Remove the appropriate slot cover(s) at the rear of the case where the card will be inserted.
Align the PCI-e card with the corresponding slot on the motherboard (which should be installed in the case).
Press the PCI-e card firmly down into the slot until it clicks into place.
Secure the installed card to the chassis using the retaining mechanism or screw(s) at the rear of the case slot opening.

How do I connect the ARGB Hub and Front LED for the MSI MPG GUNGNIR 100D case?

The ARGB Hub connection procedure is as follows:

1 to 8 ARGB Hub Connection:

Connect the JRAINBOW (ARGB) cables from the lighting elements (like fans) to the corresponding numbered ports (LED1 through LED4) on the MSI ARGB Hub.
Connect the power for the hub via a SATA Power connector to the POWER port on the hub.
If using a separate LED Switch for lighting control, connect it to the LED SW port.
Connect the SYS_FAN output from the hub to a motherboard SYS_FAN header (e.g., SYS_FAN1-4).
Connect the control/data input from the front panel (if applicable) to the DATA port on the hub, or connect the JRAINBOW output directly to the motherboard JRAINBOW (ARGB) header for motherboard control.

Connecting PWM Mode and ARGB LED to motherboard:

Connect the fan control wire to the motherboard’s SYS_FAN header (e.g., SYS_FAN1-4). Connect the ARGB lighting control wire (JRAINBOW) either to a motherboard JRAINBOW1 or JRAINBOW2 header, referencing the pinout:

Pin	JRAINBOW1	JRAINBOW2
1	+5V	Data
2	Data	No Pin
3	No Pin	Ground
4	Ground

The illustration shows connecting JRAINBOW to JRAINBOW2 header on the motherboard for ARGB control, and connecting the fan cable to SYS_FAN1-4 header.