MORRIS MPHD-6263 (01) PDF Document

The technical data for the MORRIS MPHD-6263 hair dryer is as follows:

Voltage: 220-240V

Frequency: 50/60Hz

Power: 1800-2200W

When using the MORRIS MPHD-6263 hair dryer, you should always observe the following basic safety precautions:

1. Before first use, check that the voltage on the rating label matches the mains voltage in your home.

2. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid a hazard.

3. When used in a bathroom, unplug it after use as the proximity of water is a hazard even when switched off.

4. For additional protection, the installation of a residual current device (RCD) with a rated residual operating current not exceeding 30 mA is advisable in the electrical circuit supplying the bathroom. Ask your installer for advice.

5. WARNING – Do not use this appliance near bathtubs, showers, basins or other vessels containing water.

6. Do not use the hair dryer for any purposes other than those described in the instruction manual.

7. This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities if they have been given supervision or instruction. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

8. Do not use outdoors.

9. Always unplug the hair dryer when not in use and before cleaning.

10. To protect against electric shock, do not immerse the appliance in water or any other liquids.

11. Do not spray aerosol products when the hair dryer is in operation.

12. Do not leave the hair dryer switched on when you are not using it.

13. Do not use attachments other than those supplied.

14. The air inlet and outlet openings should never be obstructed to prevent it from getting too hot.

15. Keep your hair away from the immediate vicinity of the inlet opening to prevent it from being drawn in.

16. Store the appliance in a cool, dry place. Do not use it when there is water in your hands.

To use the MORRIS MPHD-6263 for drying your hair, follow these steps:

1. Put the plug in the wall socket.

2. Switch the appliance on by selecting the desired setting for airflow and temperature.

3. Dry your hair by making brushing movements while holding the dryer at a small distance from your hair.

The airflow and temperature can be adjusted using the following speed and heating settings:

“0”: OFF

“I”: LOW SPEED AND LOW HEAT

“II”: HIGH SPEED AND HIGH HEAT

“*”: This is the “Cool” button. After drying your hair, you can use this button to set your style with a continuous flow of cool air.

If the airflow is inadvertently obstructed during use, the built-in thermal safety cut-off will automatically switch off the appliance. The hair dryer will switch on again automatically after cooling down for a few minutes. Ensure the air inlet and outlet openings are never obstructed to prevent this from happening.

The concentrator enables you to direct the airflow at the hair that you are styling.

To attach: Connect the concentrator by simply snapping it onto the appliance.

To detach: Disconnect it by pulling it off.

1. The main body of the appliance can be cleaned with a dry cloth.

2. The attachments can be cleaned with a moist cloth or rinsed under a running tap. Always remove the attachments from the appliance before cleaning them. Make sure the attachments are completely dry before using or storing them.

Never rinse the main appliance with water.

When not in use, unplug the appliance. Allow the hair dryer to cool down completely and then store it in a dry location. Never wrap the cord around the appliance, as this will cause the cord to wear prematurely and break.

If the supply cord of the appliance becomes damaged, it must be replaced to avoid a hazard. You can do this by returning the appliance to the retailer from which it was purchased or to a similarly qualified person for replacement.

Your product is designed and manufactured with high-quality materials and components which can be recycled and reused. Electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/recycling centre.