MONESSEN AVFL60PIF (01) PDF Document

If you smell gas:

• DO NOT try to light any appliance.

• DO NOT touch any electrical switch.

• DO NOT use any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

DO NOT install this appliance in a bedroom or bathroom. Please refer to Section F of the Installation Manual for proper appliance placement.

NOTE: For higher elevations please see the manual regarding input rating reductions.

WARNING! DO NOT place combustible objects in front of the appliance. High temperatures may start a fire. Avoid placing candles, electronics and other heat-sensitive objects on mantel or hearth. Heat may damage these objects.

A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children, pets and other at risk individuals out of the room and away from hot surfaces.

Clear Space: 3 FT. IN FRONT OF APPLIANCE.

The appliance should run three to four hours continuously on high. Turn the appliance off and allow it to completely cool. This cures the materials used to manufacture the appliance.

NOTICE! Open windows for air circulation during appliance break-in.

• Some people may be sensitive to smoke and odors.

• Smoke detectors may activate.

WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life.

1. This appliance is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burner by hand.

2. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow safety instructions regarding what to do if you smell gas. If you do not smell gas, go to next step.

3. To light the burner:

• Equipped with wall switch: Turn ON/OFF switch to ON.

• Equipped with remote or wall control: Press ON or FLAME button.

• Equipped with thermostat: Set temperature to desired setting.

4. If the appliance does not light after three tries, call your service technician or gas supplier.

1. Equipped with wall switch: Turn ON/OFF switch to OFF.

• Equipped with remote or wall control: Press OFF button.

• Equipped with thermostat: Set temperature to lowest setting.

2. Service technician should turn off electric power to the control when performing service.

The IntelliFire Touch with ODS intermittent pilot ignition system comes with a battery backup system that enables the system to operate in a power outage. A factory-installed battery pack is located in the control cavity of the appliance.

To Operate Appliance Using Battery Power (DC):

1. Access the control cavity of the appliance. Make sure unit is off and cool. Lift the barrier screen off of the appliance. Remove the logs or stone if installed. Remove crushed glass media and deflection glass panel from hearth pan. Remove two (2) screws securing burner assembly to appliance, set aside. Lift the burner assembly and place the two engine supports, provided under the engine, against lower front space at the bottom of the face, and slide into the slots at the bottom of the engine assembly.

2. Locate the battery tray and insert four AA cell batteries. Battery polarity must be correct or module damage will occur.

3. Turn the appliance on according to the instructions below for the appropriate type of control:

• Wall Switch: Toggle the switch as you would under normal circumstances.

• Wireless Remote: Remote receiver is integrated into the ignition module. Use the remote to turn the appliance on. To preserve battery life, do not use the HI/LO flame or THERMOSTAT options.

NOTICE: Batteries should only be used as a power source in the event of an emergency power outage. Batteries should not be used as a primary long-term power source.

Wall Switch:

• Toggle the switch to OFF.

• Remove the batteries from the battery tray.

Wireless Remote:

• Use the remote to turn the appliance off.

• Remove the batteries from the battery tray.

NOTICE: Some functionality will be lost when using battery backup including remote control, lights, or any other auxiliary functions that require household 110-120 VAC power.

The Electronic Control Module (IFT2-ECM) has a three-position ON/OFF/REMOTE selector switch.

OFF Position: The appliance will not respond to any commands from the IntelliFire Mobile App, IFT-RC150U or IFT2-RC450 remote controls. The unit should be in the OFF position during installation, service, fuel conversion and to reset the IFT2-ECM in the event the system goes into a LOCK-OUT mode. When switched to the OFF position while the appliance is operating, the system will shut down.

ON Position: The appliance will ignite and run continuously at the HIGH flame setting. No adjustment in flame height is possible. The IFT2-ECM has a safety feature that will automatically shut down the fireplace after 9 hours of continuous operation in the ON position.

Remote Position: The remote position allows operation of the appliance from the IntelliFire app, IFT2-RC450 or IFT-RC150U remote controls. The IFT2-ECM switch must be in the REMOTE position to pair the IFT2-ECM with the remote controls.

NOTICE! When the IFT2-ECM selector switch is in the ON position, the ECM shall not respond to the wired wall switch, mobile app or wireless remote controls.

In the unlikely event that the remote wall switch malfunctions and will not turn off the appliance, you may choose one of the following actions to turn off the appliance:

Turn off power to the appliance (if back-up batteries are not installed):

• Unplug appliance from electrical source, if you cannot unplug then:

• Locate house circuit breaker for appliance.

• Turn off the circuit breaker.

• Turn the reset switch in the front face to the off position.

CAUTION! Risk of burns! Appliance surfaces are hot when operating and during cool down. Use care and wear gloves when opening the front and accessing components inside the appliance.

When first operated, this appliance may release an odor for the first several hours. This is caused by the burning off of any oils remaining from manufacturing or from finishing materials or adhesives used around the appliance during installation.

Odor may also come from dust, pet dander, deodorizing room sprays and other foreign debris that collects on the surface of the burner and crushed glass media when the unit is not in use for an extended period of time. To avoid odors caused by these substances, have your qualified service technician thoroughly inspect and clean your appliance prior to the first use of each season.

No action is necessary. Noise is caused by metal expanding and contracting as it heats up and cools down, similar to the sound produced by a furnace or heating duct. This noise does not affect the operation or longevity of the appliance.