Free English MITSUBISHI ELECTRIC GT2103-PMBDS2 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD MITSUBISHI ELECTRIC GT2103-PMBDS2 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the general specifications for the MITSUBISHI ELECTRIC GT2103-PMBDS2?
| Item | Specifications |
|---|---|
| Operating Ambient Temperature | 0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically) |
| Storage Ambient Temperature | -20 to 60°C |
| Operating Ambient Humidity | 10 to 90% RH, non-condensing |
| Storage Ambient Humidity | 10 to 90% RH, non-condensing |
| Vibration Resistance | Conforms to JIS B3502 and IEC61131-2. Intermittent vibration: Frequency 5 to 8.4Hz, Half-amplitude 3.5mm; Frequency 8.4 to 150Hz, Acceleration 9.8m/s². Continuous vibration: Frequency 5 to 8.4Hz, Half-amplitude 1.75mm; Frequency 8.4 to 150Hz, Acceleration 4.9m/s². Sweep Count: 10 times each in X, Y and Z directions. |
| Shock Resistance | Compliant with JIS B3502 and IEC61131-2 147m/s² (15G) Three times in each X, Y, or Z direction |
| Operating Atmosphere | No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage) |
| Operating Altitude | 2000m (6562 ft.) max. |
| Installation Location | Inside control panel |
| Overvoltage Category | II or less |
| Pollution Degree | 2 or less |
| Cooling Method | Self-cooling |
| Grounding | Grounding with a ground resistance of 100Ω or less. If impossible, perform grounding to the control panel. |
What are the performance specifications for the MITSUBISHI ELECTRIC GT2103-PMBDS2?
| Category | Item | Specification |
|---|---|---|
| Display Section | Display Device | TFT monochrome display |
| Screen Size | 3.8″ | |
| Resolution | 320 x 128 dots | |
| Display Size (WxH) | 89.0 x 35.6 (3.51 x 1.41) mm (inch) | |
| Display Character | 16-dot standard font: 20 characters x 8 lines (two-byte characters) 12-dot standard font: 26 characters x 10 lines (two-byte characters) |
|
| Display Color | Monochrome (black and white) 32 scales | |
| Backlight | Type | 5 colors LED (white, green, pink, orange, red) (Not replaceable) |
| Life | Approx. 50000 h (operating ambient temperature: 25°C, display intensity: 50%) | |
| Touch Panel | Type | Analog resistive film |
| Key size | Minimum 2 x 2 dots (per a key) | |
| Life | 1 million times or more (Operating force: 0.98N or less) | |
| Memory | User Memory Capacity | Memory for storage (ROM): 3 MB |
| Life (Number of Write Times) | 100,000 times | |
| Built-in Interface | RS-232 (Rear Face) | 1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps Connector shape: MINI-DIN6-pin (female) |
| RS-232 (Side Face) | 1 channel Transmission speed: 115200/57600/38400/19200/9600/4800 bps Connector shape: 9-pin terminalblock |
|
| USB (Device) | 1 ch | |
| SD Card | 1 channel SDHC card supported (max. 32 GB) | |
| Buzzer Output | Single tone (tone length adjustable) | |
| Environmental Protective Structure | Outside enclosure: IP67F Inside enclosure: IP2X | |
| External Dimensions (W x H x D) mm (in) | 113 x 74 x 27 mm (4.45 x 2.92 x .07) (inch) | |
| Panel Cutting Dimensions (W x H x D) | 105 x 66 (4.14 x 2.6) mm (inch) | |
| Weight | 0.2 kg | |
| Compatible Software Package | GT Works3 Version1.119Z or later (Sold separately) | |
What are the power supply specifications for the MITSUBISHI ELECTRIC GT2103-PMBDS2?
| Item | Specification |
|---|---|
| Input Power Supply Voltage | 24 VDC (+10%, -15%) |
| Power Consumption (Under the Maximum Load) | 2.2 W or less |
| Power Consumption (Backlight Off) | 1.6 W |
| Inrush Current | 30 A or less (1ms, 25°C, at the maximum load) |
| Permissible Instantaneous Power Failure Time | Within 5ms |
| Noise Immunity | Noise voltage: 1000 Vp-p, Noise width: 1 µs (by noise simulator of 30 to 100 Hz noise frequency) |
| Dielectric Withstand Voltage | 500 VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal) |
| Insulation Resistance | 10 MΩ or larger by insulation resistance tester (between the GOT’s power supply terminals and the GOT’s grounding terminal) |
| Electrical Wire Size | No. of wire per terminal: 1; Solid wire 0.14 to 1.5 mm², AWG26 to AWG16; Stranded wire 0.14 to 1.0 mm², AWG26 to AWG16; Ferrules with plastic sleeve 0.25 to 0.5 mm², AWG24 to AWG20. No. of wire per terminal: 2; Solid wire 0.14 to 0.5 mm², AWG26 to AWG20; Stranded wire 0.14 to 0.2 mm², AWG26 to AWG24. |
| Applicable Solderless terminal | Solderless terminal for M3 screw RAV1.25-3, V2-N3A, FV2-N3A |
| Ferrules with Plastic Sleeve | AI 0.25-6BU (AWG24), AI 0.34-6TQ (AWG22), AI 0.5-6WH (AWG20) (Phoenix Contact Inc.) |
| Crimper type | CRIMPFOXZA3 (Phoenix Contact Inc.) |
| Tightening torque (terminal screws) | 0.22 to 0.25 N·m |
What are the hardware features of the MITSUBISHI ELECTRIC GT2103-PMBDS2?
| No. | Name | Description |
|---|---|---|
| (1) | Display section | Displays the utility screen and the user-created screen. |
| (2) | Touch panel | For operating the touch switches in the utility and the user-created screen. |
| (4) | RS-232 interface (Rear face) | For communicating with a controller or connecting a personal computer (FA transparent function) with a 6-pin MINI-DIN connector. For connecting multiple GOTs, a barcode reader, an RFID, or a serial printer. |
| (5) | RS-232 interface (Side face) | For communicating with a controller or connecting a personal computer (Female MINI-DIN 6-pin). |
| (8) | Power supply terminal | Power supply input terminal, FG terminal. |
| (9) | USB interface (Device) | For transferring data and storing data (Connector shape: Mini-B). |
| (11) | Installation fitting | For fixing the GOT to the control panel. |
| (12) | SD card interface | For SD card installed. |
| (13) | SD card access LED | ON: SD card accessed OFF: SD card not installed or SD card installed but removal possible. |
| (14) | Battery | Space for housing the battery. |
| (15) | SD card unit connector (inside the cover) | For mounting the SD card unit. |
What are the panel cutting dimensions required for installing the MITSUBISHI ELECTRIC GT2103-PMBDS2?
You need to open an installation hole on the control panel with the following dimensions:
| Model | A | B | C | Panel Thickness |
|---|---|---|---|---|
| GT2103-P | 105 (4.14) (+1 (0.04), 0 (0)) | 66 (2.60) (+1 (0.04), 0 (0)) | 13 (0.52) or more | 1 (0.04) to 4 (0.16) |
Note: Dimensions are in mm (inches).
How do I install the MITSUBISHI ELECTRIC GT2103-PMBDS2 into a panel?
Follow these steps to install the MITSUBISHI ELECTRIC GT2103-PMBDS2:
1. Install the provided packing into the packing installation groove on the rear face of the GOT.
2. Insert the rear face of the GOT into the panel opening.
3. Insert the hook of a supplied installation fitting into the mounting hole of the GOT. Slide the installation fitting toward the GOT’s rear face. Viewing from the rear, slide the fitting to the left to fix it, and then tighten the screw within the specified torque range of 0.20 N·m to 0.25 N·m. Use 4 fittings to fix the GOT at the top and the bottom.
4. After installation is complete, remove the protective film from the display section.
CAUTION: Use a panel that has no warpage, damage, or unevenness on its surface to ensure a waterproof effect. Tighten mounting screws within the specified torque range. Undertightening can cause the GOT to drop or lose its waterproof/oilproof effect. Overtightening can damage the GOT or distort the panel, which may impair visibility and lead to incorrect inputs.
How do I remove the MITSUBISHI ELECTRIC GT2103-PMBDS2 from a panel?
1. Remove the mounting screws of the installation fittings in reverse order of installation.
2. Remove the installation fittings from the GOT.
3. Carefully pull the GOT out from the panel opening.
How do I install and remove the SD card on the MITSUBISHI ELECTRIC GT2103-PMBDS2?
DANGER: Removing the SD card while it is being accessed can interrupt GOT processing for about 20 seconds, during which the unit will be inoperable. This can affect system operation and cause an accident. Always disable SD card access in the utility before removal.
CAUTION: Removing the data storage while it’s being accessed can damage the storage and files.
To Install the SD Card:
1. Before inserting, either turn off the GOT or go to the utility screen and select [Access inhibit] for the SD card. Touch [Utility main menu] -> [Data control] -> [SD card access] -> [Permissions], and select [Access inhibit].
2. Check that the SD card access LED turns off.
3. Open the SD card cover and insert the SD card with its front side (name plate side) facing outward. Close the SD card cover.
4. To enable access, touch [SD card access] -> [Access inhibit], and select [Permissions]. Check that the SD card access LED turns on.
To Remove the SD Card:
1. In the GOT utility, navigate to [Utility main menu] -> [Data control] -> [SD card access] -> [Permissions], and select [Access inhibit].
2. Open the SD card cover and carefully remove the SD card. Support the card by hand as it may pop out.
What is the outline procedure to start and operate the MITSUBISHI ELECTRIC GT2103-PMBDS2?
Follow this general procedure to operate the MITSUBISHI ELECTRIC GT2103-PMBDS2:
1. Preparing Project Data: Install GT Designer3 Version1 on a personal computer and create the necessary project data.
2. Installing an Extension Unit and Option: Install any optional units as required.
3. Installing the GOT and Power Supply Wiring: Mount the GOT into the control panel and perform the necessary power supply wiring.
4. Writing Package Data: Transfer the project data from a personal computer or data storage (like an SD card) to the GOT.
5. Connecting the GOT and the Controller: Connect the GOT to the controller (e.g., PLC) with the appropriate communication cable.
6. Starting Monitoring: Turn on the GOT and the connected system to begin monitoring.
What daily maintenance should be performed on the MITSUBISHI ELECTRIC GT2103-PMBDS2?
| Item | Inspection Item | Inspection Method | Criterion | Corrective Action | |
|---|---|---|---|---|---|
| 1 | GOT installation status | Check for loose screws. | Securely tightened | Retighten screws with the specified torque. | |
| 2 | Connection status | Loose terminal screws | Retighten screws with a screwdriver. | Not loose | Retighten terminal screws. |
| Proximity of solderless terminals | Visual check | Proper intervals | Correct intervals. | ||
| Loose contactors | Visual check | Not loose | Retighten contactor fixing screws. | ||
| 3 | Usage status | Dirt on the protective sheet | Visual check | Not outstanding | Replace the sheet with a new sheet. |
| Foreign material adherence | Visual check | No foreign matter adherence | Remove and clean the foreign material. |
What periodic maintenance is recommended for the MITSUBISHI ELECTRIC GT2103-PMBDS2?
Perform the following half-yearly or yearly inspections:
| No. | Category | Inspection Item | Inspection Method | Criterion | Action |
|---|---|---|---|---|---|
| 1 | Surrounding environment | Ambient temperature | Make measurement with thermometer or hygrometer | Display section: 0 to 50°C Other portions: 0 to 50°C |
For use in control panel, temperature inside control panel is ambient temperature. |
| Ambient humidity | 10 to 90%RH | ||||
| Atmosphere | Measure corrosive gas | No corrosive gas | |||
| 2 | Power supply | 24VDC voltage check | Measure voltage across terminals. | 20.4 to 26.4VDC | Change supply power |
| 3 | Change | Looseness | Visual check | No dirt, foreign matter sticking | Remove, clean |
| Dirt, foreign matter | |||||
| 4 | Connection status | Loose terminal screws | Retighten screws with screwdriver | Not loose | Retighten connector fixing screws |
| Proximate solderless terminals | Visual check | Proper intervals | Correct | ||
| Loose connectors | Visual check | Not loose | Retighten connector fixing screws |
How should I clean the screen of the MITSUBISHI ELECTRIC GT2103-PMBDS2?
Always keep the GOT in a clean condition. To clean the GOT, wipe the dirty part with a soft cloth using neutral detergent or ethanol.
Precautions for screen cleaning:
Do not use solvents such as acetone, benzene, toluene, and alcohol, as they may deform the protective sheet or peel the paint. Additionally, do not use spray solvents, as this may cause an electrical failure of the GOT and peripheral devices.
What should I do if the screen on my MITSUBISHI ELECTRIC GT2103-PMBDS2 is completely black or white?
If the screen is completely black, the liquid crystal display or BootOS may be faulty. If the screen is completely white, the GOT hardware may be faulty. In either case, follow these restoration steps:
1. Reinstalling BootOS.
2. Reinstalling standard monitor OS.
If the GOT is not restored by steps 1 and 2, perform the following:
3. Reinstalling CoreOS and then the standard monitor OS.
If the GOT is still not restored, it requires a troubled product investigation.
What is the GOT restoration procedure if my MITSUBISHI ELECTRIC GT2103-PMBDS2 malfunctions?
If the MITSUBISHI ELECTRIC GT2103-PMBDS2 has malfunctioned temporarily due to noise or other issues, follow these steps in order to check if it can be restored. If the GOT is not restored after a step, proceed to the next one.
| Step | Procedure | Possible Cause | Action if Not Restored |
|---|---|---|---|
| (A) | Press the GOT reset switch. | The GOT may have malfunctioned temporarily due to noise. | Proceed to (B). |
| (B) | Power the GOT ON/OFF. (Power OFF the PLC first). | Proceed to (C). | |
| (C) | Reset or power ON/OFF the PLC CPU. | Proceed to (D). | |
| (D) | Power the GOT and PLC CPU ON/OFF simultaneously. | Proceed to (E). | |
| (E) | Connect the cable again. | The cable connection may be faulty. | Proceed to (F). Securely connect the cable. If an error occurs again, product investigation is needed. |
| (F) | Reinstall the project data. | Data may have been destroyed by an action such as powering the GOT OFF during data transfer. | Proceed to (G). Do not power the GOT OFF while transferring data. If an error occurs again, product investigation is needed. |
| (G) | Reinstall the OS. | Proceed to (H). | |
| (H) | Take the action described in the “Action” column of the installation status check sheet. | The GOT may have malfunctioned temporarily due to noise. | Proceed to (I). |
| (I) | The GOT is not restored even by performing (A) to (H). | N/A | Product investigation is needed. |
How can I identify the position of an error on the MITSUBISHI ELECTRIC GT2103-PMBDS2 system?
To identify the source of an error:
1. Identify the error position, modify the sequence program or replace the module where the error occurs, and check whether the error occurs again.
2. If the error reoccurs, other causes are considered.
Checking the error in the PLC:
1. Check the type of the error detected in the PLC using GX Works2 or other compatible software.
2. Check each module and the installation and grounding status of the cables according to the error message on the PLC CPU.
• Checking the error occurrence timing.
• Check the timing of the error occurrence.