FREE ENGLISH MINIWARE TS21 (01) PDF DOCUMENT.
FREE ENGLISH MINIWARE TS21 (01) PDF USER GUIDE.
FREE ENGLISH MINIWARE TS21 (01) PDF USER MANUAL.
FREE ENGLISH MINIWARE TS21 (01) PDF OWNER GUIDE.
FREE ENGLISH MINIWARE TS21 (01) PDF OWNER MANUAL.
FREE ENGLISH MINIWARE TS21 (01) PDF REFERENCE GUIDE.
FREE ENGLISH MINIWARE TS21 (01) PDF INSTRUCTION GUIDE.
FREE ENGLISH MINIWARE TS21 (01) PDF REFERENCE MANUAL.
FREE ENGLISH MINIWARE TS21 (01) PDF INSTRUCTION MANUAL.
FREE ENGLISH MINIWARE TS21 (01) PDF OPERATING INSTRUCTIONS.
CLICK HERE TO DOWNLOAD MINIWARE TS21 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What are the safety notices and warnings for using the MINIWARE TS21?
General Safety:
• Please only use power adapters specially designed for this product or certified by your country/region.
• Do not operate in humid environments.
• Do not operate in flammable and explosive environments.
• Please keep the product surface clean and dry.
Warnings:
• When using the MINIWARE TS21, please turn off the power when not in use or left unattended to prevent fire.
• After the power is turned on, the temperature of the soldering tip in operation will reach 100°C – 450°C (212°F – 842°F). Be careful to avoid burns.
• Do not soak the MINIWARE TS21 in water or use it with wet hands to prevent electric shock.
• Do not use DC and USB-C interfaces at the same time.
• When using this tool, place it on a stable desktop or workbench. When not in use, store it properly.
Precautions:
• The MINIWARE TS21 controller is composed of precision components; dropping shall be avoided.
• After 5 minutes of continuous operation at full power above 350°C, or 40 minutes of continuous use, the controller temperature will reach above 50°C.
• When using it for the first time, it is normal for the soldering tip to emit a small amount of smoke due to the heating of the electrical heating elements.
Usage Notice:
This appliance is intended for use by persons from 14 years and above. Persons with reduced physical, sensory or mental capabilities or a lack of experience and knowledge should only use it if they have been given instruction concerning use of the appliance in a safe way and understand the hazards involved. Children should be supervised to ensure that they do not play with the appliance.
What are the operating environment specifications for the MINIWARE TS21?
| Working State | Non – working State | ||
|---|---|---|---|
| Temperature | +0°C ~ +50°C | -20°C ~ +60°C | |
| Relative Temperature | High Temperature | 40°C ~ 60°C 5% ~ 60% RH | 40°C ~ 60°C 5% ~ 60% RH |
| Low Temperature | 0°C ~ 40°C 5% ~ 90% RH | 0°C ~ 40°C 5% ~ 90% RH | |
What are the main interfaces and buttons on the MINIWARE TS21?
The interfaces and buttons of the MINIWARE TS21 are as follows:
1. Soldering Tip Heating End
2. Soldering Tip Connection End
3. Anti-slip Cap
4. Soldering Tip Insertion End
5. Button A
6. Button B
7. OLED Screen
8. Ground Screw
9. USB Type-C Interface
What are the product and working parameters for the MINIWARE TS21?
Product Parameters:
| Screen | 128*32, 0.91-inch monochrome OLED |
| USB Interface | USB Type-C |
| Dimension | 109*15mm |
| Controller Weight | 32 g |
Working Parameters:
| Working voltage and power | DC 9V-24V 60W MAX / PD 100W MAX |
| Temperature control range | 100°C – 450°C |
| Temperature stability | ±3% |
What power sources can be used with the MINIWARE TS21 and how fast do they heat up?
The MINIWARE TS21 Precision Soldering Iron supports two types of power inputs:
1. PD power source with USB Type-C interface: This includes chargers, power banks, etc., powered by a standard USB-C to USB-C power cable.
PD Power Warming Time (30-300°C):
| Power | Warming time |
|---|---|
| 100W | 3s |
| 60W | 3s |
| 40W | 4s |
| 27W | 5s |
| 18W | 6s |
2. DC power source: This includes power adapters, power supplies, battery packs, etc., connected via a USB-C adapter (not included in delivery).
DC Power Warming Time (from 30°C to 300°C):
| Working voltage | Working Current | Power | Time to warm |
|---|---|---|---|
| 9V | 4A | 36W | 5s |
| 12V | 4.5A | 54W | 4s |
| 16V | 3.5A | 56W | 4s |
| 19V | 3A | 57W | 3s |
| 24V | 2.5A | 60W | 3s |
How do I install the soldering tip and anti-slip cap on the MINIWARE TS21?
Initial Installation:
1. Insert the soldering tip into the TS21 controller.
2. Fix the ground wire with the ground screw (if required).
3. Connect the USB Type-C power cable to the TS21 power source, turn on the power and follow the instructions on the screen.
Note: If the MINIWARE TS21 shows “No tip!” after power is turned on, it means the soldering tip is not firmly installed. Please reinstall the soldering tip.
Installation of anti-slip cap:
The anti-slip cap enhances grip comfort and operation stability.
1. Installation and fixing: Put the anti-slip cap onto the front end of the controller and fix it with double-sided adhesive tape.
2. Heat shrink reinforcement: Set an appropriate temperature (150 – 200 °C is recommended) with a hot air gun, and evenly heat the anti-slip cap to make it shrink fully and fit closely with the handle of the soldering iron. After installation, the anti-slip cap will be more stable.
What are the factory default settings for the MINIWARE TS21?
| Preset temperature units | °C | |
| Preset Temperature | T1 Temp | 300°C |
| T2 Temp | 350°C | |
| T3 Temp | 400°C | |
| Sleep temperature | 100°C | |
| Sleep time | 1 min | |
What do the different screen displays on the MINIWARE TS21 mean during startup and standby?
After the power is turned on, the MINIWARE TS21 will first display the brand icon and then enter the standby state. If the soldering tip temperature exceeds the safe temperature (40 °C) in the standby state, the screen will display the temperature as a warning.
| Display | Meaning |
|---|---|
| MINIWARE logo | Brand icon on startup. |
| Standby interface icon | Indicates the device is in standby mode. |
| HW:vX.XX FW:vX.X.X |
Displays the software and hardware version number. |
| Resistive: X.X Temp: XX Volts: XX.X |
Displays current status: tip internal resistance, input voltage, and tip temperature. |
| High temperature warning icon with value (e.g., 280) | Indicates the current tip temperature when it exceeds the safe temperature in standby. |
How do I access and change the parameter settings on the MINIWARE TS21?
1. In standby mode, short press Button B to enter the setting mode.
2. In setting mode, press Button A or B to select the setting item you want to modify.
3. Long press Button A to enter the modification state for the selected item.
4. Press Button A or B to select the appropriate setting value.
5. Wait for 5 seconds after selection. The parameter will be modified successfully and the device will automatically return to the setting mode. Other settings can be modified in the same way.
6. After all settings are completed, long press Button B to save the modifications and return to the standby mode.
Other Functions in Standby Mode:
• Press and hold Button A to display the current internal resistance of the soldering tip.
• Press and hold Button B to display the current firmware version.
Note: In standby mode, the MINIWARE TS21 will enter an off-screen state if it stands still for a long time. You can wake it up by shaking the controller to enter the standby state.
What are the available menu settings on the MINIWARE TS21?
| First Menu | Second Menu | Range | Menu Explanation |
|---|---|---|---|
| Power settings | Min Volt | DC, 3s – 6s, Default DC | Input selection. |
| Volt Set | 2500 mV – 4200 mV, Default 3000 mV | Minimum voltage of a single battery when powered by a battery pack. | |
| Max Power | 20 – 100W, Default 60 W | Maximum power limit. | |
| Welding Settings | Work Temp 1 | 100-450°C, Default 300°C | Preset temperature 1. |
| Work Temp 2 | 100-450°C, Default 350°C | Preset temperature 2. | |
| Work Temp 3 | 100-450°C, Default 400°C | Preset temperature 3. | |
| Boost temp | 100-450°C, Default 400°C | Preset working temperature for boost mode. | |
| Temp step | 1-50, Default 10 | Step length for each key operation during temperature adjustment. | |
| Idle Settings | Sleep Temp | 100-highest working temperature, Default 100°C | Standby temperature in sleep state; value is not higher than working temperature. |
| Sleep Time | Off, 10s-10m, Default 1m | Time to enter sleep state from working mode when stationary. | |
| Idle Time | Off, 10s-10m, Default Off | Time to enter standby state from sleep mode. | |
| User settings | Temp unit | °C, °F, Default °C | Temperature display unit. |
| Display Dir | Auto, Left, Right; Default Auto | Screen display direction. In different modes, the screen display direction is reversed, and the button function remains unchanged. | |
| Animation Speed | Off, Slow, Medium, Fast; Default Medium | Menu animation display speed. | |
| Back Light | 1-10, Default 5 | Screen display brightness. | |
| Light | Off, On, Auto; Default Auto | Fill light switch. | |
| Advanced settings | Temperature compensation | -30 – +30, Default 0 | Set the temperature difference compensation between 300°C and actual temperature. |
| Restore Settings | Restore factory setting. |
What are the button functions for the MINIWARE TS21 in different modes?
| Interface/Mode | Button | Single Press | Long Press |
|---|---|---|---|
| Standby Interface | Button A | Start heating | Display current status |
| Button B | Enter the menu option | Display hardware and software version | |
| Menu interface | Button A | Left adjustment | Select to enter |
| Button B | Right adjustment | Return to upper menu | |
| Parameter adjustment interface | Button A | Left adjustment | Quick left adjustment |
| Button B | Right adjustment | Quick right adjustment | |
| Heating interface | Button A | Switch preset working temperature among T1 / T2 / T3 | Quickly heating up (Boost operation) |
| Button B | Temporarily adjust the temperature (the value won’t be saved after restarting) | Return to standby |
How do I perform a heating or boost operation with the MINIWARE TS21?
Heating Operation:
In standby mode, press Button A. The MINIWARE TS21 will enter heating working mode. After the temperature is heated to the preset working temperature, the TS21 will automatically maintain a constant temperature.
Boost Operation:
In the heating working state, press and hold Button A. The MINIWARE TS21 will enter boost heating mode. The temperature of the soldering tip will rise to the boost heating temperature and maintain a constant temperature. When Button A is released, the temperature will drop back to the preset working temperature.
To stop heating, long press Button B in heating mode to return to standby mode.
How do I adjust the temperature on the MINIWARE TS21?
The MINIWARE TS21 has two temperature adjustment methods:
1. Select preset temperature:
In standby state, press Button A to select between preset temperatures T1, T2, or T3. After selection, the TS21 will heat up to the selected preset temperature and maintain it.
2. Direct Temperature Adjustment:
In the heating state, press Button B to enter the “Work Temp” menu for the current working temperature setting. Press Button A or B to adjust the temperature. The setting will be automatically saved and the device will return to heating mode after 5 seconds of no operation. The iron will then heat to the newly set temperature. This modification is valid for the current session only and will not be saved after a power cycle.
Note: If the power supply voltage is too low, the screen will show “Low volt!”. Please replace the power source.
How do the sleep and standby states work on the MINIWARE TS21?
Entering Sleep Mode:
In working mode, if the MINIWARE TS21 remains still for 60 seconds (this is the factory default, adjustable via the “Sleep Time” setting), it will enter sleep mode. The “zZ” symbol will appear on the screen, and the soldering tip will cool down to the sleep temperature (adjustable via the “Sleep Time” setting).
Exiting Sleep Mode:
When movement is detected, the TS21 will automatically exit sleep mode and return to working mode. The soldering tip will heat up to the working temperature it was at before entering sleep mode.
Entering Standby State:
The MINIWARE TS21 can be set to return to the standby state after standing still for a certain period at the sleep temperature. This is configured using the “Idle Time” setting. After an additional 60 seconds in standby mode (factory default, adjustable via “Sleep Time”), the screen of the TS21 will turn off.
What do the icons on the heating interface of the MINIWARE TS21 mean?
| Screen Area (Label) | Display Content | Definition |
|---|---|---|
| A | Temperature value and unit | Instant working temperature of the soldering tip. |
| B | Boost mode icon | Indicates boost mode is active. |
| No display | Indicates normal working state (not in boost mode). | |
| C | Voltage value and unit | Current power source voltage. |
| D | Solid line | Instant working power bar; the length of the power bar indicates the ratio of the current instant power to the maximum power. |
| E | Moving person icon | TS21 is in a moving state. |
| No display | TS21 is in a stationary state. | |
| T1 / T2 / T3 | Indicates the currently selected preset temperature (T1, T2, or T3). | |
| F | zZ icon | TS21 is in sleep mode. |
| G | Numerical value | Current preset temperature. |
How do I replace a soldering tip on the MINIWARE TS21?
1. Please replace the soldering tip only after the power is off and the tip has cooled down.
2. Pull out the original soldering tip from the controller.
3. Reinsert another iron tip firmly into the controller.
4. Turn on the power again. If the MINIWARE TS21 shows: “NO TIP!”, it means that the soldering tip is not firmly installed. Please power off and reinsert the soldering tip.
What types of soldering tips are available for the MINIWARE TS21?
There are 3 kinds of soldering tips available for the MINIWARE TS21:
• TS21-KU: A knife-style tip with a 7.4mm width.
• TS21-I: A conical fine-point tip with a 6mm length.
• TS21-IS: A smaller conical fine-point tip with a 5mm length.
How should I maintain the soldering tip of my MINIWARE TS21?
1. When not in use for a long time, it is recommended that the soldering tip be properly tinned to prevent oxidation.
2. Do not let the soldering tip be heated at a high temperature for a long time to avoid dry burning.
3. When soldering, do not apply too much pressure on the soldering tip to rub the solder joints to avoid damage to the tip.
4. Never use rough materials or files to clean the tip of the soldering iron.
5. If the surface of the soldering tip has oxidized and does not stick to tin, you can rub it with 600-800 mesh gold steel emery cloth and clean it with ethyl propanol or an equivalent solution. To prevent further oxidation, dip it in tin immediately after heating it up to 200°C.
6. Do not use chlorine or acid-rich flux; only use synthetic resin or activated resin flux.
What should I do if there is no display on the MINIWARE TS21 screen after powering it on?
1. Check the power source and cable to ensure they are connected properly and supplying power.
2. Check if the device can enter DFU mode. To do this, connect it to a computer while holding Button A and see if a virtual disk appears.
Why is the displayed temperature of my MINIWARE TS21 jumping around the preset temperature?
Please check the following:
1. Is the soldering tip being used for the first time or was it stored in a humid environment? If so, wait for the soldering tip to be fully heated, and the temperature should stabilize.
2. Ensure the soldering tip has been installed correctly and is seated firmly.
3. Check if the power cable is in poor contact. Try a different cable or power source if possible.
Why does my MINIWARE TS21 restart automatically or display a “Ti” icon?
1. Check if the power supply is plugged in and powered on normally.
2. Verify that the power parameters (voltage, wattage) of your power source meet the usage requirements of the MINIWARE TS21.
What does it mean if the screen on my MINIWARE TS21 displays an “X” icon?
This icon indicates a problem with the soldering tip. Please check the following:
1. Ensure the soldering tip has been installed correctly.
2. The soldering iron tip may have burned out and needs to be replaced.
Why doesn’t the tip of my MINIWARE TS21 stick to the solder?
There are several potential reasons for this issue:
1. The temperature of the soldering tip may exceed 400°C, causing rapid oxidation.
2. The soldering tip may not be properly tinned.
3. There is a lack of flux, or you are using solder with low purity or low tin content.
4. You may have wiped the soldering tip with a dry sponge or material with high sulfur content or dryness, which can contaminate the tip.
5. The tip may have come into contact with organic substances such as plastics, silicon grease, or other chemicals.
How do I update the firmware on the MINIWARE TS21?
1. First, download the applicable soldering iron firmware for the MINIWARE TS21 to your computer.
2. Press and hold Button A of the TS21 and connect it to the computer via the USB Type-C cable. The TS21 will enter DFU mode, and the screen will display “DFU:X.XX”. A virtual disk will also appear on the computer.
3. Copy the prepared .hex firmware file to the root directory of the virtual disk.
4. When the firmware suffix changes from .hex to .rdy, the update is complete. Disconnect the USB connection to finish the firmware upgrade.
CLICK HERE TO DOWNLOAD MINIWARE TS21 (01) PDF DOCUMENT