MILWAUKEE M12 CML (01) PDF Document

The technical data for the MILWAUKEE M12 CML is as follows:

Different colour temperatures can be selected on the MILWAUKEE M12 CML by pressing the colour button. The display corresponds to the following temperatures:

To turn the MILWAUKEE M12 CML on, press the power button once. To turn the device off, press the power button again.

The operating mode of the MILWAUKEE M12 CML can be changed by pressing the MODE button. There are three available modes representing different light intensities: mode 1, mode 2, and mode 3.

Yes, the MILWAUKEE M12 CML features mode memory. The selected operating mode is available again when you switch the device back on.

To insert the battery pack, align it with the opening at the bottom of the MILWAUKEE M12 CML and push it until it clicks into place. To remove it, press the release buttons on the sides of the battery pack and pull it downward away from the device.

Do not direct the light beam at persons or animals and do not stare into the light beam yourself, even from a distance. Staring into the light beam of the MILWAUKEE M12 CML may result in serious injury or vision loss.

Always remove the battery pack from the MILWAUKEE M12 CML before starting any maintenance or adjustments on the machine.

The MILWAUKEE M12 CML features a battery fuel gauge located near the power button. The LEDs indicate the remaining charge capacity:

Four LEDs illuminated: 100% capacity remaining.

Three LEDs illuminated: 75% capacity remaining.

Two LEDs illuminated: 50% capacity remaining.

One LED illuminated: 25% capacity remaining.

Yes, the MILWAUKEE M12 CML is equipped with a magnet to help keep it in position. However, ensure that the luminaire does not cause harm if its magnet fails to keep it in position.

The light source of the MILWAUKEE M12 CML is not replaceable. When the light source reaches its end of life, the entire luminaire must be replaced.

The colour matching light of the MILWAUKEE M12 CML creates light close to natural sunlight to match colour specs for painting cars and detecting scratches and imperfections in cars for detail work. It can also be used for general and heavy maintenance, collision repair, and paint re-work.

In case of contact with battery acid from the MILWAUKEE M12 CML, wash it off immediately with soap and water. If it contacts your eyes, rinse thoroughly for at least 10 minutes and seek medical attention immediately.

To reduce the risk of fire or injury due to a short circuit, never immerse the MILWAUKEE M12 CML, the battery pack, or the charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids such as seawater, certain industrial chemicals, or bleach can cause a short circuit.

Batteries for the MILWAUKEE M12 CML which have not been used for some time should be recharged before use. Temperatures exceeding 50 degrees Celsius (122 degrees Fahrenheit) reduce battery performance, so avoid extended exposure to heat or sunshine to prevent overheating.

For optimum life-time, the batteries must be fully charged after use. To obtain the longest possible battery life, remove the battery pack from the charger once it is fully charged.

For battery storage longer than 30 days:

1. Store the battery where the temperature is below 27 degrees Celsius and away from moisture.

2. Store the battery in a 30% to 50% charged condition.

3. Every six months of storage, charge the battery as normal.

Lithium-ion batteries used in the MILWAUKEE M12 CML are subject to Dangerous Goods Legislation requirements. Transportation must be done in accordance with local, national, and international provisions and regulations.

Commercial transport of lithium-ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport must be carried out exclusively by appropriately trained persons, and the process must be accompanied by corresponding experts.

When transporting batteries for the MILWAUKEE M12 CML:

Ensure that battery contact terminals are protected and insulated to prevent short circuit.

Ensure that the battery pack is secured against movement within the packaging.

Do not transport batteries that are cracked or leak.

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of the Milwaukee service agents.

If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit number on the label and order the drawing at your local service agents or directly at Techtronic Industries GmbH.

The IP54 rating indicates the protection class for the MILWAUKEE M12 CML, which means it is protected against dust ingress and splashing water from any direction.

No, the MILWAUKEE M12 CML is only suitable for indoor use. You must never expose the tool to rain.

Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. They must be collected separately. Waste batteries, waste accumulators, and light sources must be removed from the MILWAUKEE M12 CML before disposal.

The MILWAUKEE M12 CML carries the following marks:

European Conformity Mark

UK Conformity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark

The PDF recommends using M12B… battery types for the MILWAUKEE M12 CML to ensure proper operation and compatibility.

The Colour Rendering Index (CRI) for the MILWAUKEE M12 CML is 98+. This high rating ensures that the light produced is close to natural sunlight, which is essential for accurate colour matching and detecting imperfections in paintwork.

The luminous flux of the MILWAUKEE M12 CML varies by mode: High mode provides 1000 lm, Medium mode provides 600 lm, and Low mode provides 300 lm.

Depending on the battery pack used (2.0 Ah to 6.0 Ah), the MILWAUKEE M12 CML weighs between 0.58 kg and 0.83 kg according to EPTA-Procedure 01/2014.

An open book icon indicates that you should read the instructions carefully before starting the MILWAUKEE M12 CML machine.

A diamond-shaped symbol with the Roman numeral III inside indicates that the MILWAUKEE M12 CML has Class III electrical protection, meaning it relies on a separated extra-low voltage supply for safety.

With a 4.0 Ah battery, the MILWAUKEE M12 CML provides 6 hours of lighting in High mode, 8 hours in Medium mode, and 14 hours in Low mode.

Yes, the MILWAUKEE M12 CML is specifically designed for colour matching and detail work, as its light is close to natural sunlight, allowing for the detection of scratches and imperfections.

The MILWAUKEE M12 CML is only suitable for indoor use. If it is accidentally exposed to rain, you should stop using it immediately, remove the battery, and ensure it is dry before attempting to use it again, as per the warning in the PDF.

You should check with your local authority or retailer for recycling advice and collection points for waste batteries and electrical equipment from the MILWAUKEE M12 CML.

The MILWAUKEE M12 CML battery pack should be stored where the temperature is below 27 degrees Celsius (approximately 80 degrees Fahrenheit) to prevent degradation.

The MODE memory feature ensures that the selected operating mode of the MILWAUKEE M12 CML is automatically saved and available again the next time the device is switched on.

When the colour temperature of the MILWAUKEE M12 CML is set to 2700 K, the display panel will show the number 27.

When the colour temperature of the MILWAUKEE M12 CML is set to 6500 K, the display panel will show the number 65.

Before disposing of the MILWAUKEE M12 CML, you must remove all waste batteries, accumulators, and light sources from the equipment, and ensure any personal data is deleted from the device.

Waste batteries, particularly those containing lithium like the ones used for the MILWAUKEE M12 CML, contain recyclable materials that can adversely impact the environment and human health if not disposed of in an environmentally compatible manner.

When shipping MILWAUKEE M12 CML batteries commercially, you should check with the forwarding company for further advice regarding Dangerous Goods regulations and transport requirements.

Yes, the M12-18 FC is one of the recommended chargers listed for the MILWAUKEE M12 CML in the technical data section of the PDF.

The MILWAUKEE M12 CML has three lighting modes: Mode 1 (High), Mode 2 (Medium), and Mode 3 (Low), which adjust the luminous flux and battery duration.

The battery compartment is located at the handle of the MILWAUKEE M12 CML. To access it, you slide the battery pack into the base until it clicks into position.

The maximum luminous flux of the MILWAUKEE M12 CML is 1000 lumens, achieved in the High setting.

Yes, as stated in the specified conditions of use, the MILWAUKEE M12 CML can be used for collision repair as well as general and heavy maintenance.

If the magnet fails, you must ensure that the luminaire does not cause harm or damage. The safety instructions emphasize ensuring the device does not cause harm if its magnet fails to keep it in position.

There are five colour temperature settings available on the MILWAUKEE M12 CML: 2700 K, 3500 K, 4500 K, 5500 K, and 6500 K.

The MILWAUKEE M12 CML is designed for use with M12B… series battery packs.

The symbol showing a head with rays entering an eye indicates that you should not stare at the operating light source of the MILWAUKEE M12 CML to avoid potential eye damage.

Yes, the specified conditions of use in the PDF mention its application in professional settings such as car painting, detail work, collision repair, and heavy maintenance.