MI REDMI NOTE 6 PRO M1806E7TG (01) PDF DOCUMENT

To turn on the MI REDMI NOTE 6 PRO M1806E7TG, long press the power button. Then, follow the on-screen instructions to configure the device.

The MI REDMI NOTE 6 PRO M1806E7TG has the following controls and ports:

Volume Buttons: Located on the right side of the device, above the Power Button.

Power Button: Located on the right side of the device, below the Volume Buttons.

USB Port: Located on the bottom edge of the device.

The SIM card tray on the MI REDMI NOTE 6 PRO M1806E7TG supports two configurations:

Configuration 1: Nano-SIM card in the first slot and a Nano-SIM card in the second slot.

Configuration 2: Nano-SIM card in the first slot and a Micro SD card in the second slot.

Please consider the following for Dual SIM functionality on the MI REDMI NOTE 6 PRO M1806E7TG:

• Dual 4G SIM requires the support of local telecom operator services, and may not be available in all regions.

• Only certain regions and telecom operators support VoLTE.

• System updates may be applied when network optimization occurs. For details, please refer to the system version in use on the device.

The MI REDMI NOTE 6 PRO M1806E7TG has an electronic label for certification information. To access it, please select Settings > About Phone > Verification or select Settings, then type “Verification” into the search bar.

Update your phone’s operating system using the built-in software update feature, or visit our authorized service outlets. Updating software through other means may damage the device or result in data loss, security issues, and other risks.

Yes, the MI REDMI NOTE 6 PRO M1806E7TG is restricted to indoor use only when operating in the 5150 to 5350Mhz frequency range in the following countries: AT, BE, BG, HR, CY, CZ, DK, EE, FI, FR, DE, EL, HU, IE, IT, LV, LT, LU, MT, NL, PL, PT, RO, SK, SI, ES, SE, UK.

The operating temperature range for the MI REDMI NOTE 6 PRO M1806E7TG is 0°C to 40°C. Using this device in environments outside of this temperature range may damage the device.

Please follow these safety instructions when charging your MI REDMI NOTE 6 PRO M1806E7TG:

• Charge this device only with the included or authorized cable and power adapter. Using unauthorized or other adapters may cause fire, electric shock, and damage the device and the adapter.

• After charging is complete, disconnect the adapter from both the device and the power outlet.

• Do not charge the device for longer than 12 hours.

• For the AC/DC Adapter, the socket-outlet shall be installed near the equipment and shall be easily accessible.

• Install the adapter near the device in an easily accessible position.

• Ensure the power adapter used meets the requirements of Clause 2.5 in IEC60950-1/EN60950-1 and has been tested and approved according to national or local standards.

• Do not use your phone to make calls while it is charging.

The MI REDMI NOTE 6 PRO M1806E7TG is provided with a built-in battery. Follow these guidelines to avoid damaging the battery or the device:

• Do not attempt to replace the battery yourself.

• There is a risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to instructions.

• The battery must be recycled or disposed of separately from household waste. Mishandling the battery may cause fire or explosion.

• Do not disassemble, hit, crush, or burn the battery. In case of deformation, stop using the battery immediately.

• Do not short circuit the battery to avoid overheating, burns, or other personal injuries.

• Do not place the battery in high-temperature environments. Overheating may cause explosion.

• Do not disassemble, hit, or crush the battery to avoid battery leaks, overheating, or explosion.

• Do not burn the battery to avoid fire or explosion.

Do not try to repair the MI REDMI NOTE 6 PRO M1806E7TG yourself. If any part of the device does not work properly, contact Mi customer support or bring your device to an authorized repair center.

To prevent possible hearing damage, do not listen at high volume levels for long periods.

Follow these safety precautions when using your MI REDMI NOTE 6 PRO M1806E7TG:

• Follow relevant laws and regulations. Do not use your phone in potentially explosive environments, including fuelling areas, below decks on boats, fuel or chemical transfer or storage facilities, or areas where the air contains chemicals or particles like grain, dust, or metal powders.

• Obey all posted signs to turn off wireless devices such as your phone or other radio equipment.

• Do not use your phone in hospital operating rooms, emergency rooms, or intensive care units. Consult your doctor and the device manufacturer to determine if operation may interfere with medical devices.

• To avoid potential interference with a pacemaker, keep a minimum separation of 15 cm between the mobile phone and the pacemaker. Use the phone on the opposite ear to your pacemaker and do not carry it in a breast pocket.

• Do not use your phone near hearing aids, cochlear implants, etc., to avoid interference with medical equipment.

• Respect aircraft safety regulations and turn off your phone on board the aircraft when required.

• When driving, use your phone in accordance with relevant traffic laws and regulations.

• To avoid lightning strike, do not use your phone outdoors during thunderstorms.

• Do not use your phone in places with high humidity such as bathrooms, as it may result in electric shock, injury, fire, and charger damage.

• Observe any rules that restrict using mobile phones in specific cases and environments.

• Keep your device dry.

This product should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle responsibly to promote the sustainable reuse of material resources. To safely recycle your device, please use return and collection systems or contact the retailer where the device was originally purchased. The battery must also be recycled or disposed of separately from household waste.

The MI REDMI NOTE 6 PRO M1806E7TG offers the following frequency bands and maximum radio-frequency power in EU areas only:

If your MI REDMI NOTE 6 PRO M1806E7TG causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

The MI REDMI NOTE 6 PRO M1806E7TG meets government requirements for exposure to radio waves. The exposure standard for wireless devices is known as the Specific Absorption Rate (SAR).

EU Guidelines:

Body-worn SAR testing has been carried out at a separation distance of 5 mm. To meet RF exposure guidelines during body-worn operation, the device should be positioned at least this distance away from the body. If you are not using an approved accessory, ensure that whatever products are used are free of any metal and that it positions the phone with the indicated distance away from the body.

FCC Guidelines:

The SAR limit set by the FCC is 1.6W/kg. For body-worn operation, this device has been tested and meets the FCC RF exposure guidelines for use with an accessory that contains no metal and is positioned a minimum of 1.0 cm from the body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. If you do not use a body-worn accessory and are not holding the device at the ear, position the handset a minimum of 1.0 cm from your body when the device is switched on.

The Specific Absorption Rate (SAR) values for the MI REDMI NOTE 6 PRO M1806E7TG are as follows:

SAR 10g limit: 2.0 W/Kg

• SAR Value Head: 0.755 W/Kg

• SAR Value Body: 1.476 W/Kg (5mm distance)

SAR 1g limit: 1.6 W/Kg

• SAR Value Head: 0.75 W/Kg

• Body-worn: 0.78 W/Kg (10mm distance)

• Hotspot: 1.14 W/Kg (10mm distance)