MAXIMA 09399400 (01) PDF Document

The MAXIMA 09399400 has the following specifications:

Dimensions: W53 x D71 x H127 cm

Weight: 77 kg

Electrical Power: 2,2 kW

Input: 400V / 50Hz / 3 Phase

Speed: 1500-3000 RPM

Capacity: 20 L

The processing capacities for the MAXIMA 09399400 are as follows:

Bowl: 20 L

Ayran: 12 kg

Hummus: 8 kg

Onion: 6 kg

Sauce: 10 kg

Soup: 12 kg

Follow these steps to operate your MAXIMA 09399400:

1. Place the bowl on the shaft and turn it clockwise to lock it in place.

2. Place the blades inside the bowl.

3. Put the product inside the bowl.

4. Close the top lid and secure it with the locking mechanism.

5. Press the Start 1 button to start cutting.

6. To change the speed, first, press the Stop button then press the Start 2 or Start 1 button according to the desired speed.

7. Press the Stop button to stop the machine. Open the locking mechanism and lid.

8. Remove the blades before using the bowl tilting arm.

9. Tilt the bowl using the tilting arm to extract the product.

To clean the MAXIMA 09399400, follow these guidelines:

Regularly check and clean the appliance, its parts, and accessories.

Always switch off and disconnect the power supply before any cleaning or maintenance.

Do not use aggressive or abrasive cleaning agents, solvents, or petroleum-based agents. Use a mild food-safe cleaning product.

Do not use a scourer or any sharp objects during cleaning as this may cause damage to the machine.

Never hose down the machine or immerse it in water or any other liquid. Wipe the exterior with a damp cloth. Do not use a steamer.

Never let the power cable or power plug get wet.

The blades must be cleaned manually as they can get damaged in a dishwasher.

The maintenance actions for the MAXIMA 09399400 are:

Daily: Cleaning and disinfecting. Thoroughly clean the appliance and accessories after every use with a soft cloth and food-safe detergent.

Weekly: Surface cleaning. It is recommended to wipe the exterior of the appliance at least once a week.

Depending on usage: Blades replacement. It is recommended to replace blades as they wear.

If the MAXIMA 09399400 does not work, check the following:

If the appliance is switched off, switch on the appliance.

If the power supply has been interrupted, check the power supply and plug in the power cable.

If the blades of the MAXIMA 09399400 do not rotate, check the following:

Main fuse failure: Check the main fuse, switch it on and ensure that there is electricity.

Thermal fuse failure: Reset thermal fuse.

Lid is not fully closed: Ensure the lid is closed.

Bowl is not in place: Ensure the bowl is placed in the right position.

If the blades of the MAXIMA 09399400 do not cut, check the following:

Blades rotate in the wrong direction: Replace phase terminals in the main supply.

Blades are stuck: Stuck products should be carefully removed and separated into smaller pieces.

If there is a leakage from the lid sealing on the MAXIMA 09399400, consider the following:

Excessive amount of liquid ingredients: Reduce the amount of liquid ingredients.

Lid sealing misplacement: Fix the sealing placement.

Operating speed is too high: Reduce the operating speed.

Lid lock is not closed properly: Ensure the lid lock can close the lid properly.

If you experience loud noise and vibration with the MAXIMA 09399400, check the following:

Machine has not been aligned properly: Ensure the machine foot is properly placed on the floor.

Operating speed is too high: Reduce operating speed.

If the blade of the MAXIMA 09399400 is stuck, consider the following:

Waste materials in the blade group: Stuck blades should be removed using a special tool. Contact your supplier.

Blade group or surfaces of the shaft are damaged: Replace the damaged part with a new one.

If it is difficult to open the upper lid of the MAXIMA 09399400, it is likely because there is a vacuum inside the bowl. Remove the oil inlet before attempting to open the lid.