FREE ENGLISH MAKITA UC3530AP (01) PDF USER GUIDE
FREE ENGLISH MAKITA UC3530AP (01) PDF USER MANUAL
FREE ENGLISH MAKITA UC3530AP (01) PDF OWNER GUIDE
FREE ENGLISH MAKITA UC3530AP (01) PDF OWNER MANUAL
FREE ENGLISH MAKITA UC3530AP (01) PDF REFERENCE GUIDE
FREE ENGLISH MAKITA UC3530AP (01) PDF INSTRUCTION GUIDE
FREE ENGLISH MAKITA UC3530AP (01) PDF REFERENCE MANUAL
FREE ENGLISH MAKITA UC3530AP (01) PDF INSTRUCTION MANUAL
FREE ENGLISH MAKITA UC3530AP (01) PDF OPERATING INSTRUCTIONS
CLICK HERE TO DOWNLOAD MAKITA UC3530AP (01) PDF MANUAL
If this is not the document you want for this product, click here to see if we have any other documents for this product.
MAKITA UC3530AP (01) PDF SUMMARY:
What should I do before putting the chain saw into operation?
Read the instruction manual carefully and strictly observe the safety regulations.
What should I do if one of the parts is not included in the delivery inventory?
Consult your sales agent.
What should the user do to ensure correct operation of the electric chain saw?
The user has to read the instruction manual to become familiar with the characteristics of the electric chain saw.
Who should you not lend the electric chain saw to?
It is recommended only to lend the electric chain saw to people who have proven to be experienced with electric chain saws. Always hand over the instruction manual.
What should first time users do to familiarize themselves with engine powered sawing?
First users should ask the dealer for basic instructions.
What is recommended for first time users to do to familiarize themselves with an electric chain saw?
Familiarize yourself with the use of an electric chain saw by cutting off lengths from a log on a sawhorse.
Who is not allowed to operate the electric chain saw?
Children and young persons aged under 18 years must not be allowed to operate the electric chain saw.
Who is allowed to operate the electric chain saw for training purposes?
Persons over the age of 16 years may, however, use the chain saw for the purpose of being trained while under supervision of a qualified trainer.
When should you operate the electric chain saw?
Operate the electric chain saw only if you are in good physical condition. Perform all work calmly and carefully.
When should you not operate the electric chain saw?
Never use the electric chain saw after the consumption of alcohol or drugs or medication.
What protective equipment must be used during operation of the electric chain saw?
- Protective helmet
- Face shield or goggles
- Noise protection equipment (ear muffs, ear plugs, etc.)
- Protective brace and bib overall or long trousers made of solid material
- Protective gloves made of thick leather
- Safety shoes or boots fitted with anti-skid sole, steel toe caps and protection for the leg.
What should you do with your clothing when using the electric chain saw?
The kind of clothing should be appropriate, i. e. it should be tight-fitting but not be a hindrance. Do not wear jewelry or clothing which could become entangled with bushes or shrubs.
How often should you check your protective helmet for damage and when should you replace it?
The protective helmet is to be checked in regular intervals for damage and is to be replaced after 5 years at the latest.
What should you do if you have long hair when operating the electric chain saw?
If you have long hair wear a hairnet.
When should you always wear goggles or a face shield?
During operation of the electric chain saw always wear a goggle or a face shield to prevent eye injuries.
What type of clothing is strongly recommended to be worn during operation of the electric chain saw?
The protective brace and bib overall is strongly recommended. In any case wear a long pair of trousers made of solid material during operation of the electric chain saw.
When should you always wear protective gloves?
Protective gloves made of thick leather must always be worn during operation of the electric chain saw.
What type of footwear should be worn during operation of the electric chain saw?
Safety shoes or boots fitted with anti-skid sole, steel toe caps and protection for the leg are always to be used. Safety shoes equipped with a protective layer provide protection against cuts and ensure a secure footing.
When should you not operate the electric chain saw?
Do not operate the electric chain saw when it rains or in wet or moist environment because the motor is not waterproof.
What should you do if the electric chain saw is moist?
If the electric chain saw is moist, it must not be put into operation.
What should you avoid when operating the electric chain saw?
Avoid physical contact with grounded surfaces. Do not operate the electric chain saw next to inflammable gases or dusts.
How should you lead the power supply cable while operating the electric chain saw?
Do always lead the power supply cable behind the user. Take care that the cable is not clamped or cut by sharp-edged objects. Lay the cable such that nobody is endangered.
What type of socket should the plug be inserted into?
Insert the plug only into safety sockets with approved installation. Make sure that the mains voltage corresponds to that on the identification plate.
What is the back-up fuse for the electric chain saw?
16 A.
What should you connect the electric chain saw to if it is going to be used outdoors?
If the saw is going to be used outdoors connect it to a fault-current (FI) circuit breaker.
What should you do with a cable roll if you are using one?
If using a cable roll the cable should be completely wound off.
What type of extension cords should be used for the electric chain saw?
Use only extension cords that meet the specifications in “Technical data”. If using the saw out of doors make sure that the extension cord is approved for such use.
What should you check before starting work with the electric chain saw?
Before starting work the electric chain saw must be checked for perfect function and operating safety according to the prescriptions.
What specific functions should be checked before starting work with the electric chain saw?
- The function of the chain brake
- The correct mounting of the guide bar
- The correct sharpening and tightening of the saw chain
- The firm mounting of the sprocket guard
- The easy motion of the power switch
- The function of the locking button
- The good mechanical condition of cable and plug
- The cleanliness and dryness of the handles.
When should you put the electric chain saw into operation?
Put the electric chain saw only into operation if it is completely assembled.
When should you never use the electric chain saw?
Never use the electric chain saw when it is not completely assembled.
What should you do with the adjusting tool before switching the saw on?
Remove the adjusting tool before switching the saw on.
What should you ensure while operating the chain saw?
All protective installations and guard supplied with the chain saw during operation.
What should you be aware of in your working range while operating the chain saw?
Make sure that there are no children or other persons within the working range. Also pay attention to any animals in the working vicinity.
What should you ensure before switching on the electric chain saw?
Before switching on the electric chain saw ensure that you have a safe footing.
How should you hold the electric chain saw when switching it on?
When switching on the electric chain saw always hold it with both hands. Take the back handle with the right hand and the tubular handle with the left hand. Hold the handles tightly with your thumbs facing your fingers. The bar and chain must indicate away from your body.
How should you switch on the saw?
Switch on the saw only in the manner described in this manual.
What should you not do with your saw?
Do not overload your saw. It will work better and more safely if you use it within its intended performance range.
What should you do if you observe a change in the electric chain saw’s operating behavior?
Switch off the electric chain saw immediately if you observe a change in its operating behavior.
What happens when releasing the power switch?
When releasing the power switch the chain keeps on running for a short period of time (free-wheeling).
What should you protect the power cord from?
Protect the power cord from heat, oil and sharp edges.
How should you route the power cord while operating the chain saw?
Route the power cord in such a way that in cannot get caught in branches or other objects during sawing.
What should you do if the cable is damaged or cut while operating the chain saw?
If the cable is being damaged or cut, pull out the power supply plug immediately.
What should you do if the sawing device is hit by stones, nails or other hard objects?
If the sawing device is hit by stones, nails or other hard objects, pull out the power supply plug and check the sawing device immediately.
When should you pull out the power supply plug?
- Before checking the chain tension
- Before tightening the chain
- Before replacing the chain
- Before clearing malfunctions.
What should you do when stopping work or leaving the electric chain saw?
When stopping work or leaving the electric chain saw switch off the chain saw and pull out the power supply plug. Put the electric chain saw in a safe location to prevent danger to others.
What should you do before refilling the oil tank?
For refilling the oil tank the power supply plug must be pulled out.
What should you not do when refilling the oil tank?
Do not smoke or light open fires.
What should you avoid when refilling the oil tank?
Avoid skin or eye contact with mineral oil products.
What should you always wear when refilling the oil tank?
Always wear gloves when refilling the oil tank.
What should you take care of to protect the environment when handling the chain oil?
Take care that no chain oil oozes into the soil. Use an appropriate base.
What should you do if oil has been spilled?
If oil has been spilt, clean the electric chain saw immediately.
Should you work alone with the electric chain saw?
Do not work on your own. There must be someone around in case of an emergency (within shouting distance).
How should you hold the electric chain saw during sawing operation?
During sawing operation always hold the electric chain saw with both hands. Thus you will be able to guide it safely.
When should you only use the electric chain saw?
Only use the electric chain saw during good light and visibility periods.
What should you be aware of when operating the electric chain saw?
Be aware of slippery or wet areas, and of ice and snow (risk of slipping). The risk of slipping is extremely high when working on recently peeled wood (bark).
Where should you never work with the electric chain saw?
Never work on unstable surfaces.
What should you make sure of in your working area?
Make sure that there are no obstacles in the working area, risk of stumbling. Always ensure that you have a safe footing.
Where should you never saw with the electric chain saw?
- Never saw above your shoulder height.
- Never saw while standing on a ladder.
- Never climb up into trees to perform sawing with the electric chain saw.
What should you ensure when you are working with the electric chain saw?
Ensure that the body is within the elongated swiveling range of the saw.
What should the electric chain saw be used for?
Use the electric chain saw for sawing wood only.
What should you not let the chain do when it is running?
Do not let the chain touch the ground when it is running.
What should you do when cutting wood lying directly on the ground?
If you are cutting wood lying directly on the ground, turn it over before completing the cut so that you do not cut into the ground.
What should you clear the area of the cut from?
Clear the area of the cut of foreign objects such as sand, stones, nails, wire etc. Such objects can damage the blade and cause dangerous kickback.
What should you use when sawing precut timber or thin woods?
When sawing precut timber or thin woods use a safe support (sawing jack).
What should you use when sawing precut timber or thin pieces?
When sawing precut timber or thin pieces use a stable support (sawhorse).
What should you not do when sawing timber?
- Do not saw stacked timber!
- Do not let another person steady the timber, and do not steady it with your foot!.
How should you secure round timber when using the electric chain saw?
Secure round timber.
When working on slopes, which way should you work?
When working on slopes, always work facing the slope.
What must be applied to the timber to be cut for performing crosscuts?
For performing crosscuts the toothed ledge must be applied to the timber to be cut.
How should you perform a crosscut?
Before performing a crosscut firmly apply the toothed ledge to the timber, only then can the timber be cut with the chain running. For this the electric chain saw is lifted at the back handle and guided with the tubular handle. The toothed ledge serves as a center of rotation. Continue by slightly pressing down the tubular handle and simultaneously pulling backwards the electric chain saw. Apply the toothed ledge a little bit deeper and once again lift the back handle.
When should the sawing device be running?
The sawing device must be running whenever you remove the electric chain saw from the timber.
What should you do with the electric chain saw when performing several cuts?
When performing several cuts the electric chain saw must be switched off in between.
Who should perform the works when timber must be pierced for cutting or longitudinal cuts are to be performed?
When the timber must be pierced for cutting or longitudinal cuts are to be performed it is urgently recommended to have these works carried out by specially trained persons only (high risk of kickbacks).
How should you apply the sawing device for performing longitudinal cuts?
For performing longitudinal cuts apply the sawing device at an angle which is as small as possible. Be very careful when carrying out this kind of work because the toothed ledge cannot be used.
When cutting with the bottom edge of the bar, which way may the electric chain saw be pushed if the chain is clamped?
When cutting with the bottom edge of the bar the electric chain saw may be pushed in the direction of the user if the chain is clamped.
When should you use the top edge of the bar?
For this reason use the top edge of the bar whenever possible. The electric chain saw will then be pushed away from your body.
When the timber is not free of tension, which side should you cut first?
If the timber is not free of tension, first cut the pressure side (A). Then the crosscut can be performed on the tension side (B). Thus clamping of the bar is avoided.
What should you be careful of when cutting splintery wood?
Be very careful when cutting splintery wood. Cut pieces of wood may be pulled along (risk of injuries).
What should you never use the electric chain saw for?
Never use the electric chain saw for lifting up or removing pieces of wood or other objects.
What should the electric chain saw be supported on when releasing the tension?
When releasing the tension the electric chain saw should be supported on the trunk (risk of kickbacks).
Who should carry out tension releasing works?
Tension releasing works must be carried out by trained persons. High risk of injuries.
What should you be aware of when operating the electric chain saw around branches?
Be aware of branches under tension. Do not cut free branches from below.
Where should you never perform tension releasing works?
Never perform tension releasing works standing on the trunk.
What type of work should you not use the electric chain saw for?
Do not use the electric chain saw for works in the forest, i. e. for cutting down trees or carrying out tension releasing works. The user’s mobility and safety necessary for this kind of work are not guaranteed due to the cable connection.
When cutting down a tree, which persons are allowed to be within the working range?
Ensure that only those persons are within the working range which are actually involved in cutting down the tree.
What should all persons involved in the felling have?
All persons involved in the felling have an unhindered retreat route (the retreat path should be about 45° diagonally and to the rear away from the direction of fall). Be aware of the increased risk of stumbling from electric cables!.
What should the bottom part of the trunk be free from?
The bottom part of the trunk is free from foreign bodies, underbrush and branches. Make sure to have a safe footing (risk of stumbling).
What distance should the next working place be when cutting down a tree?
The next working place is at least 2 1/2 tree lengths away.
What should you check before cutting down a tree?
Before cutting down the tree check the direction of fall and make sure that there are neither other persons nor any objects within a distance of 2 1/2 tree lengths.
What should you judge about a tree before cutting it down?
- Direction of hanging
- Loose or dry branches
- Height of the tree
- Natural hang over
- Is the tree rotten?
- Take into account the direction and the velocity of the wind.
When should you not perform any cutting down works?
If strong gusts are occurring, do not perform any cutting down works.
Which root should you start with when cutting the roots of a tree?
Start with the strongest root.
How should you cut the roots of a tree?
First perform the vertical and then the horizontal cut.
How should you notch the trunk of a tree when cutting it down?
The trunk is notched perpendicular to the direction of fall and penetrates 1/3 -1/5 of the trunk diameter. Perform the cut near the ground.
When correcting the cut, how should you do it?
When correcting the cut always do so over the whole width of the notch.
How should you cut down the tree?
Cut down the tree above the bottom edge of the notch. The cut must be exactly horizontal. The distance between both cuts must be approx. 1/10 of the trunk diameter.
What is the material between both cuts of a tree when cutting it down?
The material between both cuts serves as a hinge.
What should you never do to the hinge of a tree when cutting it down?
Never cut it through, otherwise the tree will fall without any control.
What should you insert into the cut of a tree in good time when cutting it down?
Insert felling wedges in the cut in good time.
What type of wedges should you use to secure the cut of a tree when cutting it down?
Secure the cut only with wedges made of plastic or aluminum. Do not use iron wedges.
Where should you always stay when cutting down a tree?
When cutting down a tree always stay sideways of the falling tree.
What should you be aware of when withdrawing after having performed the cut down of a tree?
When withdrawing after having performed the cut down be aware of falling branches.
When working on a sloping ground, where must the user of the electric chain saw stay when cutting a tree down?
When working on a sloping ground the user of the electric chain saw must stay above or sidewards of the trunk to be cut or the already cut down tree.
What should you be aware of when cutting down a tree?
Be aware of trunks which may roll towards you.
When does kickback occur?
Kickback occurs when the tip of the blade (especially the top quarter) inadvertently comes into contact with wood or other solid objects.
Which way is the electric chain saw thrown during a kickback?
In this case the electric chain saw is thrown without any control and with high energy potentials in the direction of the user.
How can you prevent kickbacks?
- Never apply the end of the bar when starting to make a cut. Always observe the end of the bar.
- Never use the bar end for sawing. Be careful when continuing to cut.
- When starting to perform a cut the chain must be running.
- Ensure that the chain is always sharpened correctly. Pay special attention to the hight of the depth limiter (for detailed information see the chap. “Sharpening the saw chain”).
- Never cut several branches at the same time. When cutting a branch ensure that no other branch is touched.
- When crosscutting a trunk be aware of the trunks next to it. It is recommended to use a saw jack.
How should you carry the electric chain saw?
Carry the electric chain saw with the tubular handle. The saw bar indicates backwards. never carry or transport the electric chain saw with the chain running.
How should you never carry the saw?
Never carry the saw by the power cord. Do not disconnect the plug by pulling on the power cord.
What should you do when changing your position during work?
When changing your position during work switch of the electric chain saw and actuate the chain brake in order to prevent an inadvertent start of the chain.
What should you do when transporting the electric chain saw over long distances?
When transporting the electric chain saw over long distances the power supply plug must be pulled out and the bar protection cover, included in the delivery, must be applied.
How should you ensure safe positioning of the electric chain saw during car transportation?
Ensure safe positioning of the electric chain saw during car transportation to avoid oil leakage.
Where should you store the saw?
Store the saw in a secure, dry, lockable room out of reach of children. It must not be stored outdoors.
What should you do with the oil tank before storing the electric chain saw over a long period of time or shipping it?
For storing the electric chain saw over a long period of time or shipping it the oil tank must be completely emptied.
What type of containers should you use for transporting and storing chain oil?
Only use approved and marked containers for transporting and storing chain oil.
What should you do for performing maintenance works on the electric chain saw?
For performing maintenance works switch of the electric chain saw, pull out the power supply plug and secure it.
What should you make sure of before starting to work?
Before starting to work, always make sure that the saw is in safe working order, in particular the chain brake and run-out brake. Make sure that the saw chain is always sharpened and tightened correctly.
What should be inspected regularly?
Have the chain brake and run-out brake inspected regularly.
What should you regularly check on the electric chain saw?
- Regularly check the cable to the power supply for damage of the covering.
- Regularly clean the electric chain saw.
- Regularly check the tank cap for tightness.
What should you do if the plastic case of the electric chain saw is damaged?
If the plastic case is damaged, have it immediately repaired by a skilled person.
What should you do if the ON/OFF switch is defective?
Do not use the saw if the ON/OFF switch is defective. Have it repaired by a qualified person.
What should you observe?
Observe the accident prevention instructions issued by the competent trade federations and insurance companies.
What should you not perform on the electric chain saw?
Do not perform any modifications on the electric chain saw. you will endanger your safety.
What type of maintenance and repair works should you perform on the electric chain saw?
Perform only the maintenance and repair works described in the instruction manual. All other works must be carried out by the MAKITA service.
What type of spare parts and accessories should you use on the electric chain saw?
Use only original MAKITA spare parts and accessories.
What happens if you apply spare parts which are not original MAKITA parts or accessories and bar/chain combinations or lengths?
Applying spare parts which are not original MAKITA parts or accessories and bar/chain combinations or lengths results in a high risk of accidents.
What should you make sure is always available close by in the event of a possible accident?
For the event of a possible accident, please, make sure that a first aid box is always immediately available close by.
What information should you give if you ask for help in the event of an accident?
- Place of accident
- What happened
- Number of injured persons
- Kind of injuries
- Your name.
What are the symptoms of injury to blood vessels or the nervous system from excessive vibration?
“Falling asleep” (numbness), tingling, pain, stabbing sensation, alteration of skin color or of the skin.
What is the procedure for mounting the bar and chain?
- Put the electric chain saw on a stable surface.
- Release the chain brake by pulling the hand guard in the direction of the arrow.
- Flip up the sprocket guard quick tightener.
- Push in the sprocket guard quick tightener firmly against spring pressure, and slowly turn it counter-clockwise until you feel it engage.
- Keep pushing in, and turn it as far as possible counter-clockwise.
- Release the sprocket guard quick tightener (remove pressure) and now turn it clockwise to its original position.
- Repeat this procedure until the sprocket guard is unscrewed.
- Pull the sprocket guard up slightly, pull out of the rear fittings and remove.
- Place the saw chain on the sprocket.
- Guide the saw chain into the upper guide groove of the guide bar.
- Make sure the cutting edges of the saw chain on the top of the guide bar must point in the direction of the arrow.
What should you always wear when working on the guide bar or saw chain?
Always wear protective gloves and pull out the power supply plug.
When should you switch on the electric chain saw?
Switch on the electric chain saw only after having assembled it completely and inspected!.
How do I line up the sprocket guard?
Line up the hole in the sprocket guard with the threaded pin. Turn the chain tensioning screw to align the chain tensioning pin with the hole in the guide bar.
How do I guide the saw chain?
Using your left hand, lightly press the guide bar against the holder on the housing and guide the saw chain around the nose sprocket on the guide bar. While doing this, pull the saw chain slightly in the direction shown by the arrow.
How do I tighten the saw chain?
Firmly push in and simultaneously turn the sprocket guard quick tightener (clockwise) in order to screw on the sprocket guard, but do not tighten it yet. Lift the tip of the guide bar slightly and turn the chain tensioner clockwise until the saw chain engages in the guide groove on the lower side of the guide bar. Push in the sprocket guard quick tightener again and tighten by turning clockwise.
How do I release the sprocket guard quick tightener?
Release the sprocket guard quick tightener (remove pressure) until it turns freely, then fold it in as shown in the illustration.
How do I mount the sprocket guard?
First press the sprocket guard into the mounting and then push it onto the threaded pin.
How do I check the chain tension?
The chain has the proper tension when it lies against the bottom edge of the guide bar and can be easily pulled by hand about 3-4 mm (about 1/8") up from the guide bar. Check the chain tension frequently – new chains tend to get longer during use! When checking the chain tension the motor must be switched off and the power supply plug pulled out. If the chain is too loose: Loosen the sprocket guard quick tightener by about a quarter turn. Tighten the chain as described under “Tightening the saw chain.”.
What should I do for even wear of the chains, sprocket and guide bar running surfaces?
Use 2 or 3 saw chains alternately. In order to guarantee a uniform wear of the groove in the bar, the bar should be turned over whenever replacing the chain.
What is the chain brake?
The electric chain saw comes with an inertial chain brake as standard equipment. If kickback occurs due to contact of the guide-bar tip with wood, the chain brake will stop the chain through inertia if the kickback is sufficiently strong. The chain will stop within a fraction of a second.
What is the run-out brake?
The electric chain saw comes with a run-out brake as standard equipment. The run-out brake ensures that the chain comes to a stop immediately when the ON/OFF switch is released, thus preventing the chain from continuing to run and presenting a hazard.
How do I engage the chain brake manually?
To engage the chain brake manually, simply push the hand guard forward (towards the tip of the saw) with your left hand.
How do I release the chain brake?
Pull the hand guard towards you until you feel it catch. The brake is now released.
What happens when the chain brake is actuated?
When the chain brake is actuated the power supply to the motor will be cut off.
What type of oil should I use for the saw chain?
Use a special oil with adhesive addition for lubricating the saw chain and bar. The adhesive addition prevents that the oil is centrifuged too fast from the sawing device. Do not use mineral oils. In order to protect the environment, the use of biologically decomposable oil is prescribed. The saw chain oil sold by MAKITA, called BIOTOP, is made of special vegetable oils and is biologically decomposable to 100%. BIOTOP has been granted the “blue angel” for being particularly favorable to the environment.
How long is biologically decomposable oil stable?
Biologically decomposable oil is stable only for a limited period of time. It should be consumed within 2 years from the date of manufacture (printed on the container).
Why should I never use waste oil?
Waste oil is very dangerous for the environment and contains high amounts of carcinogenic substances. The residues in the waste oil result in a high degree of wear and tear at the oil pump and the sawing device. In the case of damage caused by using waste oil or inappropriate saw chain oil, the product guarantee will be null and void.
What should I do if I am not planning to use the saw for an extended period of time?
Empty the oil tank and put in a small amount of regular engine oil (SAE 30), and then run the saw for a time. This is necessary to flush out all remaining bio-degradable oil from the oil tank, oil-feed system, chain and guide bar, as many such oils tend to leave sticky residues over time, which can cause damage to the oil pump or other parts. The next time you use the saw, fill the tank with BIOTOP chain oil again.
How do I refill the oil tank?
- Only if the motor is switched off and the power supply plug is pulled out!
- Thoroughly clean the oil tank around the cap to prevent dirt from entering the tank.
- Unscrew the tank cap and fill in chain oil until it is on a level with the bottom edge of the filler socket.
- Tightly screw on the tank cap.
- Thoroughly remove any oil that has overflown.
What should I do before operating the saw for the first time?
Before operating the saw for the first time, the oil feed system must be completely filled, until the chain oil lubricates the chain and guide bar. This procedure can take up to two minutes.
How can I control the oil level?
The oil level can be controlled in the sight glass.
What must I do to ensure sufficient lubrication of the saw chain?
There must always be enough oil in the tank.
How do I lubricate the saw chain?
- Only if the motor is switched off and the power supply plug is pulled out!
- To guarantee a trouble-free operation of the oil pump, the oil guide groove as well as the oil inlet bore in the guide bar must be cleaned in regular intervals.
Is it normal for residual chain oil to drip from the oil feed system after the saw has been turned off?
Yes, it is normal for residual chain oil to drip from the oil feed system, the guide bar and the chain for a time. This does not constitute a defect.
What happens if dirt particles accumulate on the chain oil filter?
Dirt particles that accumulate on the chain oil filter will impede the flow of chain oil. This will eventually lead to poor lubrication, and faster wear to the chain and guide bar.
When do I need to clean or replace the chain oil filter?
If the chain is no longer getting enough lubrication, the chain oil filter will need to be cleaned or replaced.
How do I clean or replace the chain oil filter?
- Remove the sprocket guard, chain, and guide bar.
- Carefully clean the area around the oil outlet hole.
- Using a small screwdriver, carefully remove the serrated washer and chain oil filter.
- Clean the chain oil filter. If it is severely contaminated, replace it.
- Plug in the chain saw and let it run until the chain oil comes out the oil outlet hole.
- Switch off the saw and unplug the power cord.
- Clean the area around the oil outlet hole with a cloth.
- Insert the chain oil filter and serrated washer as shown in Installation. When the oil filter cannot be secured with the serrated washer, replace the serrated washer with a new one.
- Put the guide bar, chain, and sprocket guard back on.
What do I need to check before connecting the saw to a source of electricity?
Always make sure to check that when the on/off switch has been pressed in and released, it automatically comes back out to the “off” position. If it does not, do not under any circumstances connect the saw to a power source – do not plug it in. Take the saw to a MAKITA service center before doing any work with it.
How do I connect the extension cord and the saw’s power cord?
Clip the extension cord and the saw’s power cord into the cord grip. Plug the saw plug into the socket of the extension cable.
How do I switch on the motor?
- Plug in the saw.
- When switching on the electric chain saw always hold it with both hands. Take the back handle with the right hand and the tubular handle with the left hand. Hold the handles tightly with your thumbs facing your fingers. The bar and chain must not be in contact with any object.
- First depress the locking button and then the power switch. Then release the locking button.
What happens immediately when I switch on the motor?
The chain starts running immediately.
What should I do to keep the motor running?
Keep the power switch depressed as long as the motor is to run.
Should I lock the power switch in the on position?
Never lock the power switch in the on position.
How do I switch off the motor?
Release the power switch.
What should I do if the saw does not start when the on/off switch is actuated?
If the saw does not start when the on/off switch is actuated, it will be necessary to release the chain brake. Pull the hand guard firmly in the direction of the arrow until you feel it catch.
What does the starting current limiter do?
These models are equipped with a starting current limiter. This electronic component prevents too abrupt starting of the electric motor.
What happens when the electrical current to the saw exceeds the permissible level?
When the electrical current to the saw exceeds the permissible level, the power supply to the motor is automatically cut off. This prevents overheating of the motor and resulting damage. To start the saw up again, release the ON/OFF switch and press it again.
What should I do if the current cutoff repeatedly switches off the saw?
Do not use the saw if the current cutoff repeatedly switches off the saw. Consult a MAKITA service center.
How do I check the chain brake?
- Start the motor as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact).
- Grasp the tubular handle firmly with one hand and hold the grip with the other.
- Switch on the motor and press the hand guard in the direction of the arrow with the back of your hand until the chain brake engages. The chain should stop immediately.
- Switch the motor off immediately and release the chain brake.
What should I do if the saw chain does not stop instantly when I test the chain brake?
If the saw chain does not stop instantly when you carry out this test, do not under any circumstances use the saw! Take the chain saw to a MAKITA service center.
How do I test the run-out brake?
- Start the motor as described (make sure you have a good footing, and place the chain saw on the ground in such a way that the guide bar is free of contact).
- Grasp the tubular handle firmly with one hand and hold the grip with the other.
- Switch the motor on and then back off. The chain should come to a full stop within two seconds of switching off the motor.
What should I do if the saw chain does not stop within two seconds when I test the run-out brake?
If the saw chain does not stop within two seconds when you carry out this test, do not use the saw! Inspect the carbon brushes.
How do I check the chain lubrication?
- Never saw when sufficient chain lubrication is not guaranteed. Otherwise the life of the sawing device will be reduced.
- Before starting work, check the oil level in the tank and the oil feeding.
- Check the fed oil quantity by following the instructions below:
- Start the electric chain saw.
- Hold the running chain saw approx. 15 cm above a trunk or the ground (use an appropriate surface).
- If the lubrication is sufficient, you will see a light oil trace because oil will be centrifuged from the chain saw.
When does the chain need sharpening?
- The sawdust from sawing humid wood looks like wood flour.
- The saw chain penetrates the wood only under great pressure.
- The cutting edge is visibly damaged.
- The sawing device is pulled to the left or the right during the sawing operation. This is caused by uneven sharpening of the chain or by damage to one side of it.
How often should I sharpen the chain?
Sharpen frequently, but without removing too much metal. Generally, 2-3 strokes of the file will be enough.
What should I do when I have sharpened the chain several times?
Have the chain resharpened in a service center when you have sharpened it yourself several times.
What is important about the cutters on the chain?
- All cutters must be of the same length. Cutters with different lengths result in rough running of the chain and can cause cracks in the chain.
- Minimum cutter length is 3 mm (0.11"). Do not resharpen the chain when the minimum cutter length has been reached; at this point, the chain must be replaced.
What determines the depth of the cut?
The depth of the cut is determined by the difference in height between the depth limiter (round nose) and the cutting edge.
What is the best depth-limiter depth?
The best results are obtained with a depth-limiter depth of 0.64 mm (.025").
What can excessive depth increase the risk of?
Excessive depth increases the risk of kickback.
What is the correct sharpening angle for all cutters?
All cutters must be sharpened to the same angle, 30°. Different angles result in a roughly, irregularly running chain, increase wear and tear, and cause chain breakage.
What is the front rake of the cutter?
The 85° front rake of the cutter results from the cut depth of the round file. If the proper file is used in the right manner, the correct front rake will be obtained automatically.
How do I sharpen the saw chain?
- Sharpen using a special file holder with a saw chain round file dia. 4.0 mm. Normal round files are not appropriate for this work.
- The file should cut only when pushed forwards (arrow). Lift the file when leading it backwards.
- First sharpen the shortest cutter. The length of this cutter is then the standard for all other cutters of the chain.
- Always guide the file as shown.
How does the file holder make file guidance easier?
The file holder makes file guidance easier. It is marked for the correct 30° sharpening angle (keep the marks parallel with the chain when filing, see illustration) and limits the cut depth to the correct 4/5 of the file diameter.
What do I need to do after sharpening the chain?
After having sharpened the chain, the height of the depth limiter must be checked by means of a chain gauge. Correct even the smallest excess height with a special flat file. Round off the front of the depth limiter.
How do I clean the guide bar and lubricate the sprocket nose?
- Protective gloves must be worn.
- Regularly inspect the bearing surfaces of the guide bar for damage, and clean them with a suitable tool.
- If the saw is used intensively it will be necessary to lubricate the return sprocket bearings regularly (once a week). To do this, first thoroughly clean the 5 mm hole at the tip of the guide bar, and then press in a small amount of multi-purpose grease.
What should I check before mounting a new chain?
Check the sprocket before mounting a new chain.
What should I do with worn-out sprockets?
Worn-out sprockets may damage the new chain and must therefore be replaced. Do not attempt to replace the sprocket yourself. Sprocket replacement requires special training and tools and must be done at a MAKITA service center.
How do I inspect and replace the carbon brushes?
- Inspect the carbon brushes at regular intervals.
- A notch on the brush shows the limit of wear.
- The carbon brush is very delicate, so be careful not to let it drop. When taking it out, be sure to note the position it was installed in, since each brush is run in with the rotor.
- Use a slotted bit screwdriver to unscrew the cover, and then pull out the brush.
- If the wear limit has not yet been reached, put the brush back in the same position and screw the cover back on.
- Run the saw briefly (about a minute) so the brushes can run in again.
What should I do after installing new carbon brushes?
After installing new carbon brushes, run the saw about 5 minutes and then check the run-out brake.
What periodic maintenance should I perform?
To ensure long life, prevent damage and ensure the full functioning of the safety features the following maintenance must be performed regularly. Guarantee claims can be recognized only if this work is performed regularly and properly. Failure to perform the prescribed maintenance work can lead to accidents.
Who is allowed to perform maintenance work on the electric chain saw?
The user of the electric chain saw is not allowed to perform maintenance works which are not described in the instruction manual. All other works must be carried out by a MAKITA service center.
| System | Cause | Observation |
|---|---|---|
| Total | No power supply, cable defective, chain brake actuated, Mains fuse blown | Electric motor does not function |
| Carbon brushes | Carbon brushes worn down | Low pulling power |
| Oil tank, oil pump | Oil tank empty, oil guide groove dirty | No oil on the saw chain |
| Brake | Brake band worn down | Saw chain does not stop instantly |
| Brake | Carbon brushes worn down | Saw chain continues to run |
What should I regularly check on the electric chain saw?
- Regularly clean the outside.
- Check the plastic case for cracks and ruptures. In case of damage have it immediately repaired at a service center.
- Resharpen the saw chain regularly and replace in time.
- Turn the guide bar over after a certain period of time so that the bearing surfaces are uniformly worn. Replace in time.
- Have the sprocket replaced in time at a service center.
- Have the chain brake inspected regularly at a service center.
- Have the run-out brake inspected regularly at a service center.
What should I check each time before putting the saw into operation?
- Check the saw chain for damage and sharpness.
- Check the chain tension.
- Check the guide bar for damage, and remove burrs if necessary.
- Perform a functional check of the chain lubrication.
- Perform a functional check of the chain brake.
- Perform a functional check of the run-out brake.
- Perform a functional check of the power switch.
- Check the power supply cable. In case of damage have it replaced at a service center.
- Check the oil tank cap for tightness.
What should I do after each shutdown?
- Clean the oil inlet bore of the guide bar.
- Clean the chain carrier, especially the oil guide groove.
How should I store the electric chain saw?
- Empty the chain oil tank.
- Demount, clean, and lubricate slightly the saw chain/guide bar. Clean the guide groove of the guide bar.
- Store the electric chain saw safely in a dry place.
- After a long storage time, have the electric chain saw checked at a service center (residual oil can become resinic and the valve of the oil pump).
Who should perform maintenance and repair work on the electric chain saw?
Any work not described in the Instruction Manual must be performed only by a MAKITA service center. The MAKITA service centers are provided with all the necessary equipment and skilled and experienced personnel to work out correct customer solutions and to advise you in all matters accordingly.
What voids all warranty claims?
Repair attempts by third parties or unauthorized persons void all warranty claims.
What kind of spare parts should I use?
Use original MAKITA spare parts only, marked. Only original spare parts and accessories guarantee the highest quality in material, dimensions, functioning and safety. Original spare parts and accessories can be obtained from your local dealer.
What happens if I use foreign spare parts instead of original MAKITA spare parts?
Using foreign spare parts instead of the original MAKITA spare parts will automatically invalidate the MAKITA product guarantee.
What are some of the reasons that I would not be covered by the product guarantee?
- Disregard of the instruction manual.
- Non-performance of the required maintenance and cleaning instructions.
- Normal wear and tear.
- Obvious overload due to permanent excess of the upper limits of capacity.
- Use of guide bars and saw chains which have not been approved.
- Use of guide bar and saw chain lengths which have not been approved.
- Use of force, improper use, misuse or accidents.
- Damage caused by overheating due to dirt obstructing the cool air supply at the motor case.
- Use of unsuitable spare parts or parts which are not original MAKITA parts, as far as they have caused the damage.
- Use of unsuitable or old oil.
- Damage related to conditions arising from lease or rent contracts.
- Works on the chain saw by unskilled persons or performance of inappropriate repairs. Cleaning, servicing and adjustment works are not covered by the guarantee. All repairs covered by the guarantee are to be performed by a MAKITA service center.
| Pos. | MAKITA no. | Qty. | Denomination |
|---|---|---|---|
| 1 | 186 114 100 | 1 | Oil tank cap compl. |
| 2 | 186 413 400 | 1 | Sprocket guard compl. |
| 3 | 970 805 410 | 2 | Carbon brushes |
| 4 | 443 030 661 | 1 | Sprocket nose bar 30 cm (12") |
| 4 | 443 035 661 | 1 | Sprocket nose bar 35 cm (14") |
| 4 | 443 040 661 | 1 | Sprocket nose bar 40 cm (16") |
| 4 | 443 045 661 | 1 | Sprocket nose bar 45 cm (18") |
| 4 | 444 035 661 | 1 | Sprocket nose bar 35 cm (14"), UC3530AP |
| 4 | 444 040 661 | 1 | Sprocket nose bar 40 cm (16"), UC4030AP |
| 5 | 518 091 646 | 1 | Saw chain 3/8", 30 cm |
| 5 | 518 091 651 | 1 | Saw chain 3/8", 35 cm |
| 5 | 518 091 656 | 1 | Saw chain 3/8", 40 cm |
| 5 | 518 091 661 | 1 | Saw chain 3/8", 45 cm |
| 6 | 951 100 633 | 1 | Chain protection cover (30-35 cm) |
| 6 | 951 100 643 | 1 | Chain protection cover (40-45 cm) |
| – | 226 211 050 | 1 | Chain oil filter (felt) |
| – | 186 411 040 | 1 | Lock washer (clamping ring) |
| 20 | 953 100 090 | 1 | Chain gauge 3/8” |
| 21 | 953 004 010 | 1 | File handle |
| 22 | 953 003 090 | 1 | Round file ø 4 mm |
| 23 | 953 003 060 | 1 | Flat file |
| 24 | 953 030 010 | 1 | File holder compl. 3/8” |
CLICK HERE TO DOWNLOAD MAKITA UC3530AP (01) PDF MANUAL