MAKITA 6260D (02) PDF MANUAL

MAKITA 6260D (02) PDF SUMMARY:

What are the safety instructions for using the cordless driver drill?

Read and understand the instruction manual before using the tool. Failure to follow all instructions may result in electric shock, fire, and/or serious injury.

---

What are the general safety rules to follow when using power tools?

• Keep the work area clean and well lit, as cluttered and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust, as power tools create sparks which may ignite the dust or fumes.
• Keep children and bystanders away while operating a power tool, as distractions can cause you to lose control.
• Power tool plugs must match the outlet, and never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools.
• Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges, and refrigerators, as there is an increased risk of electric shock if your body is earthed or grounded.
• Do not expose power tools to rain or wet conditions, as water entering a power tool will increase the risk of electric shock.
• Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool. Keep cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
• When operating a power tool outdoors, use an extension cord suitable for outdoor use, which reduces the risk of electric shock.
• Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication, as a moment of inattention while operating power tools may result in serious personal injury.
• Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
• Ensure the switch is in the off-position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.
• Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times, which enables better control of the power tool in unexpected situations.
• Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery, or long hair can be caught in moving parts.
• If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used, as the use of these devices can reduce dust-related hazards.
• Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
• Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
• Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
• Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
• Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tools operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
• Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
• Use the power tool, accessories, and tool bits, etc. in accordance with the provided instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

---

What are the safety rules specific to battery tool use and care?

• Ensure the switch is in the off position before inserting battery pack. Inserting the battery pack into power tools that have the switch on invites accidents.
• Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
• Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
• When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
• Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

---

What are some specific safety rules to consider?

• Do not let comfort or familiarity with the product replace strict adherence to drill safety rules. Using the power tool unsafely or incorrectly can lead to serious personal injury.
• Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a “live” wire will make exposed metal parts of the tool “live” and shock the operator.
• Always be sure to have a firm footing and ensure no one is below when using the tool in high locations.
• Hold the tool firmly and keep hands away from rotating parts.
• Do not leave the tool running and only operate the tool when hand-held.
• Do not touch the drill bit or the workpiece immediately after operation, as they may be extremely hot and could burn your skin.
• Some materials contain chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact, and follow material supplier safety data.

---

What are the important safety instructions for battery cartridges?

• Before using the battery cartridge, read all instructions and cautionary markings on the battery charger, the battery, and the product using the battery.
• Do not disassemble the battery cartridge.
• If operating time has become excessively shorter, stop operating immediately, as it may result in a risk of overheating, possible burns, and even an explosion.
• If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away, as it may result in loss of eyesight.
• Always cover the battery terminals with the battery cover when the battery cartridge is not used.
• Do not short the battery cartridge by touching the terminals with any conductive material, storing the battery cartridge in a container with other metal objects, or exposing the battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns, and even a breakdown.
• Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
• Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out, as it can explode in a fire.
• Be careful not to drop or strike the battery.

---

What are some tips for maintaining maximum battery life?

• Charge the battery cartridge before it is completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power.
• Never recharge a fully charged battery cartridge, as overcharging shortens the battery service life.
• Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F). Let a hot battery cartridge cool down before charging it.
• Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months.

---

What should I do before adjusting or checking the function of the tool?

Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool.

---

How do I install or remove the battery cartridge?

• Always switch off the tool before insertion or removal of the battery cartridge.
• To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge.
• To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury.
• Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly.

---

How does the switch action work?

• Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released.
• To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.

---

What is the electric brake feature?

This tool is equipped with an electric brake. If the tool consistently fails to quickly stop after switch trigger release, have the tool serviced at a Makita service center.

---

How does the reversing switch action work?

This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counter-clockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled.

---

What are some cautions related to the reversing switch?

• Always check the direction of rotation before operation.
• Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool.
• When not operating the tool, always set the reversing switch lever to the neutral position.

---

How do I change the speed?

To change the speed, first switch off the tool and then slide the speed change lever to the “2” side for high speed or “1” side for low speed. Be sure that the speed change lever is set to the correct position before operation. Use the right speed for your job.

---

What are some cautions related to the speed change lever?

• Always set the speed change lever fully to the correct position. If you operate the tool with the speed change lever positioned halfway between the “1” side and “2” side, the tool may be damaged.
• Do not use the speed change lever while the tool is running, as it may be damaged.

---

How do I adjust the fastening torque?

The fastening torque can be adjusted in 17 steps by turning the adjusting ring so that its graduations are aligned with the pointer on the tool body. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the drill marking is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. The clutch is designed not to slip at the drill marking. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.

---

Note regarding the adjusting ring:

The adjusting ring does not lock when the pointer is positioned only halfway between the graduations.

---

What should I do before carrying out any work on the tool?

Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

---

How do I install or remove a driver bit or drill bit?

Hold the ring and turn the sleeve counterclockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the sleeve clockwise to tighten the chuck. To remove the bit, hold the ring and turn the sleeve counterclockwise.

---

How do I perform a screwdriving operation?

• Adjust the adjusting ring to the proper torque level for your work.
• Place the point of the driver bit in the screw head and apply pressure to the tool.
• Start the tool slowly and then increase the speed gradually.
• Release the switch trigger as soon as the clutch cuts in.

---

What are some cautions related to screwdriving?

Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged.

---

Note on driving wood screws:

When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart.

---

How do I perform a drilling operation?

First, turn the adjusting ring so that the pointer points to the drill marking, then proceed as follows:

• Drilling in wood: When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece.
• Drilling in metal: To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals, with the exceptions of iron and brass which should be drilled dry.

---

What are some cautions related to drilling?

• Pressing excessively on the tool will not speed up the drilling. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool.
• There is a tremendous force exerted on the tool/bit at the time of hole break through. Hold the tool firmly and exert care when the bit begins to break through the workpiece.
• A stuck bit can be removed simply by setting the reversing switch to reverse rotation in order to back out. However, the tool may back out abruptly if you do not hold it firmly.
• Always secure small workpieces in a vise or similar hold-down device.
• If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery.

---

Table of Recommended Pilot Hole Sizes for Wood Screws:

Nominal diameter of wood screw (mm)	Recommended size of pilot hole (mm)
3.1 (1/8”)	2.0 – 2.2 (5/64” – 3/32”)
3.5 (9/64”)	2.2 – 2.5 (3/32” – 3/32”)
3.8 (5/32”)	2.5 – 2.8 (3/32” – 7/64”)
4.5 (11/64”)	2.9 – 3.2 (7/64” – 1/8”)
4.8 (3/16”)	3.1 – 3.4 (1/8” – 9/64”)
5.1 (13/64”)	3.3 – 3.6 (1/8” – 9/64”)
5.5 (7/32”)	3.7 – 3.9 (9/64” – 5/32”)
5.8 (7/32”)	4.0 – 4.2 (5/32” – 11/64”)
6.1 (15/64”)	4.2 – 4.4 (11/64” – 11/64”)

---

What should I do before attempting to perform inspection or maintenance?

Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.

---

How should I maintain the product?

To maintain product safety and reliability, repairs, any other maintenance, or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts.

---

How do I recycle the battery?

The only way to dispose of a Makita battery is to recycle it, as the law prohibits any other method of disposal:

1. Remove the battery from the tool.
2. a) Take the battery to your nearest Makita Factory Service Center or b) Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location.

Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under “Tools-Electric”.

---

What accessories are recommended for use with the Makita tool?

• Drill bits
• Screw bits
• Various types of Makita genuine batteries and chargers
• Rubber pad assembly
• Wool bonnet
• Foam polishing pad
• Plastic carrying case

Only use an accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita service center.

---

What is the warranty policy for Makita tools?

Every Makita tool is thoroughly inspected and tested before leaving the factory and is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.

---

When does the warranty not apply?

• If repairs have been made or attempted by others.
• If repairs are required because of normal wear and tear.
• If the tool has been abused, misused, or improperly maintained.
• If alterations have been made to the tool.

---

What liabilities does Makita disclaim?

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY. MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF “MERCHANTABILITY” AND “FITNESS FOR A SPECIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY.

---

What are the specifications of the 6260D, 6270D, 6280D, and 6390D models?

Feature	6260D	6270D	6280D	6390D
Steel Capacity	10 mm (3/8”)	10 mm (3/8”)	13 mm (1/2”)	13 mm (1/2”)
Wood Capacity	21 mm (13/16”)	25 mm (1”)	25 mm (1”)	36 mm (1-7/16”)
Wood Screw	5.1 x 38 mm (3/16” x 1-1/2”)	5.1 x 63 mm (3/16” x 2-1/2”)	6 mm x 75 mm (1/4” x 3”)
Machine Screw	6 mm (1/4”)
No Load Speed (RPM)	High: 0 – 1,200/min.	High: 0 – 1,200/min.	High: 0 – 1,200/min.	High: 0 – 1,200/min.
	Low: 0 – 350/min.	Low: 0 – 350/min.	Low: 0 – 350/min.	Low: 0 – 350/min.
Overall Length	192 mm (7-9/16”)	192 mm (7-9/16”)	220 mm (8-5/8”)	220 mm (8-5/8”)
Net Weight	1.4 kg (3.1 lbs)	1.4 kg (3.1 lbs)	1.5 kg (3.3 lbs)	1.6 kg (3.5 lbs)
Rated Voltage	D.C. 9.6V	D.C. 9.6V	D.C. 12V	D.C. 14.4V
Standard Battery	PA09, 9120, 9122, 9134, 9135	PA09, 9120, 9122, 9134, 9135	PA12, 1220, 1222, 1234, 1235	PA14, 1420, 1422, 1434, 1435