Post questions, comments, reviews or page errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: E N G L I S H INSTRUCTION MANUAL ( O r i g i n a l i n s Jig Saw t r u c t i o n s ) 4326 4327 4328 4329 008081 DOUBLE INSULATION IMPORTANT: Read Before Using. 1 ENGLISH (Original instructions) SPECIFICATIONS Model 4326 4327 4328 4329 Length of stroke 18 mm 18 mm 18 mm 18 mm Blade type B type Wood 65 mm 65 mm 65 mm 65 mm Max. cutting capacities Mild steel 6 mm 6 mm 6 mm 6 mm Strokes per minute (min-1) 3,100 500 - 3,100 500 - 3,100 500 - 3,100
Overall length Net weight 217 mm (Steel base type) 223 mm (Aluminum base type) 1.8 kg (Steel base type) 1.9 kg (Aluminum base type) 217 mm (Steel base type) 223 mm (Aluminum base type) 1.8 kg (Steel base type) 1.9 kg (Aluminum base type) 217 mm 223 mm 1.8 kg 1.9 kg
Safety class /II /II /II /II • Due to our continuing program of research and development, the specifications herein are subject to change without notice. • Specifications may differ from country to country. • Weight according to EPTA-Procedure 01/2003
END201-7 Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning before use. ･ Read instruction manual. ･ DOUBLE INSULATION ･ Only for EU countries Do not dispose of electric equipment together with household waste material! In observance of the European Directive, on Waste Electric and Electronic Equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. ENE019-1 Intended use The tool is intended for the sawing of wood, plastic and metal materials. As a result of the extensive accessory and saw blade program, the tool can be used for many purposes and is very well suited for curved or circular cuts. ENF002-2 Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated and can, therefore, also be used from sockets without earth wire. ENG905-1 Noise The typical A-weighted noise level determined according to EN60745: Model 4326,4327 Sound pressure level (LpA) : 86 dB (A) Sound power level (LWA) : 97 dB (A) Uncertainty (K) : 3 dB (A) Model 4328,4329 Sound pressure level (LpA) : 83 dB (A) Sound power level (LWA) : 94 dB (A) Uncertainty (K) : 3 dB (A) Wear ear protection ENG900-1 Vibration The vibration total value (tri-axial vector sum) determined according to EN60745:
Model 4326,4327 Work mode : cutting boards Vibration emission (ah,B) : 5.5 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode : cutting sheet metal Vibration emission (ah,M) : 5.5 m/s2 Uncertainty (K) : 1.5 m/s2 Model 4328,4329 Work mode : cutting boards Vibration emission (ah,B) : 7.0 m/s2 Uncertainty (K) : 1.5 m/s2 Work mode : cutting sheet metal Vibration emission (ah,M) : 5.0 m/s2 Uncertainty (K) : 1.5 m/s2 ENG901-1 • The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another. • The declared vibration emission value may also be used in a preliminary assessment of exposure. WARNING: • The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used. • Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). ENH101-17 For European countries only EC Declaration of Conformity Makita declares that the following Machine(s): Designation of Machine: Jig Saw Model No./ Type: 4326, 4327, 4328, 4329 Conforms to the following European Directives: 2006/42/EC They are manufactured in accordance with the following standard or standardized documents: EN60745 The technical file in accordance with 2006/42/EC is available from: Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium 31.12.2013 000331 Yasushi Fukaya Director Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium GEA005-3 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool. Work area safety 1. Keep work area clean and well lit. Cluttered or dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes. 3. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Electrical safety 4. Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock. 5. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock. 7. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
9. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. 10. Use of power supply via a RCD with a rated residual current of 30mA or less is always recommended. Personal safety 11. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. 12. Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. 13. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. 14. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury. 15. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations. 16. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts. 17. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. Power tool use and care 18. Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed. 19. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. 20. Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. 21. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users. 22. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 23. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. 24. Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Service 25. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. 26. Follow instruction for lubricating and changing accessories. 27. Keep handles dry, clean and free from oil and grease. GEB016-3 JIG SAW SAFETY WARNINGS 1. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. 2. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. 3. Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses. 4. Avoid cutting nails. Inspect workpiece for any nails and remove them before operation. 5. Do not cut oversize workpiece. 6. Check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor, workbench, etc. 7. Hold the tool firmly.
8. Make sure the blade is not contacting the workpiece before the switch is turned on. 9. Keep hands away from moving parts. 10. Do not leave the tool running. Operate the tool only when hand-held. 11. Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece. 12. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 13. Do not operate the tool at no-load unnecessarily. 14. Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data. 15. Always use the correct dust mask/respirator for the material and application you are working with. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal FUNCTIONAL DESCRIPTION CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Selecting the cutting action (For models 4328/4329) 1. Cutting action changing lever 1 008153 This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action thrusts the blade forward on the cutting stroke and greatly increases cutting speed. To change the cutting action, just turn the cutting action changing lever to the desired cutting action position. Refer to the table to select the appropriate cutting action. Position Cutting action Applications For cutting mild steel,
injury. 0 Straight line cutting action Small orbit cutting action Medium orbit cutting action Large orbit cutting action 006582 Switch action stainless steel and plastics. For clean cuts in wood and plywood. For cutting mild steel, aluminum and hard wood. For cutting wood and plywood. For fast cutting in aluminum and mild steel. For fast cutting in wood and plywood.
1 2 008082 1. Switch trigger 2. Lock button
CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Installing or removing saw blade 1. Blade holder 1 Speed adjusting dial (For models 4327/4328/4329) 2 2. Bolt 3. Hex wrench 1 008167 1. Speed adjusting dial 3 008083 CAUTION: • Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the The tool speed can be infinitely adjusted between 500 and 3,100 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 6; lower speed is obtained when it is turned in the direction of number 1. Refer to the table to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. Workpiece to be cut Number on adjusting dial Wood 5 - 6 Mild steel 3 - 6 Stainless steel 3 - 4 Aluminum 3 - 6 Plastics 1 - 4 006583 blade, resulting in a serious personal injury. • Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. • Always secure the blade firmly. Insufficient tightening of the blade may cause blade breakage or serious personal injury. • Use only B type blades. Using blades other than B type blades causes insufficient tightening of the blade, resulting in a serious personal injury. To install the blade, loosen the bolt counterclockwise on the blade holder with the hex wrench. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. Then tighten the bolt clockwise to secure the blade. 1. Bolt
CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded and heated up. • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work. 1 2 3 008084 2. Blade 3. Roller
To remove the blade, follow the installation procedure in reverse. NOTE: • Occasionally lubricate the roller. 6
Hex wrench storage 1 2 008085 1. Hook 2. Hex wrench OPERATION CAUTION: • Always hold the base flush with the workpiece. Failure to do so may cause blade breakage, resulting in a serious injury. • Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may cause a slanted cutting surface and blade breakage. Turn the tool on without the blade making any contact
When not in use, store the hex wrench as shown in the figure to keep it from being lost. Adjusting roller (For models 4326/4327) and wait until the blade attains full speed. Then rest the base flat on the workpiece and gently move the tool forward along the previously marked cutting line.
1 2 34 5 6 008154 1. Blade 2. Roller 3. Retainer 4. Hex wrench 5. Bolt 6. Base 1 2 008087 1. Cutting line 2. Base
Loosen the bolt on the back of the base with the hex wrench. Move the retainer so that the roller contacts the blade lightly. Then tighten the bolt to secure the base and the retainer. NOTE: • Occasionally lubricate the roller. Dust cover 1. Dust cover 1 008086 CAUTION: • Always wear safety goggles even when operating the tool with the dust cover lowered. Lower the dust cover to prevent chips from flying. However, when making bevel cuts, raise it all the way. Bevel cutting 008088 CAUTION: • Always be sure that the tool is switched off and unplugged before tilting the base. • Raise the dust cover all the way before making bevel cuts. With the base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the cross-shaped slot in the base.
1 2 3 008089 1. Hex wrench 2. Bolt 3. Base B) Plunge cutting 008093
Tilt the base until the desired bevel angle is obtained. The edge of the motor housing indicates the bevel angle by graduations. Then tighten the bolt to secure the base. You need not bore a starting hole or make a lead in cut if you carefully do as follows. (1) Tilt the tool up on the front edge of the base
1 2 008090 Front flush cuts 1 2 3 008091 1. Edge 2. Graduation 1. Hex wrench 2. Bolt 3. Base with the blade point positioned just above the workpiece surface. (2) Apply pressure to the tool so that the front edge of the base will not move when you switch on the tool and gently lower the back end of the tool slowly. (3) As the blade pierces the workpiece, slowly lower the base of the tool down onto the workpiece surface. (4) Complete the cut in the normal manner. Finishing edges 008094
Loosen the bolt on the back of the base with the hex wrench and slide the base all the way back. Then tighten the bolt to secure the base. Cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole 1. Starting hole 1 008092 For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter. Insert the blade into this hole to start your cut. To trim edges or make dimensional adjustments, run the blade lightly along the cut edges. Metal cutting Always use a suitable coolant (cutting oil) when cutting metal. Failure to do so will cause significant blade wear. The underside of the workpiece can be greased instead of using a coolant. Dust extraction 1. Dust cover 2. Hose 1 2 008095
Clean cutting operations can be performed by connecting this tool to a Makita vacuum cleaner. Insert the hose of the vacuum cleaner into the hole at the rear 1 of the tool. Lower the dust cover before operation. NOTE: Aluminum base type 1. Bolt 2. Fence guide 3. Hex wrench 4. Rip fence (Guide rule) • Dust extraction cannot be performed when making bevel cuts. Rip fence (optional accessory) CAUTION: • Always be sure that the tool is switched off and unplugged before installing or removing accessories. 1. Straight cuts 2 3 4 005454 2. Circular cuts Steel base type 1. Treaded knob 2. Guide facing 3. Rip fence (Guide rule)
Steel base type 1 1. Rip fence (Guide rule) 1 2 3 002777 4 Aluminum base type 4. Pin 1. Threaded knob
008096 When repeatedly cutting widths of 160 mm or less, use 1 of the rip fence will assure fast, clean, straight cuts. 4 2 2. Pin 3. Rip fence (Guide rule) 4. Fence guide
Aluminum base type 1 1. Rip fence (Guide rule) 3 005455 Steel base type 1. Rip fence (Guide rule)
008097 To install, insert the rip fence into the rectangular hole on the side of the base with the fence guide facing down. Slide the rip fence to the desired cutting width position, then tighten the bolt to secure it. 1 008098
Steel base type 1 4 2 3 1. Hex wrench 2. Bolt 3. Rip fence (Guide rule) 4. Guide facing Aluminum base type 1 1. Rip fence (Guide rule)
002776 008099 When cutting circles or arcs of 170 mm or less in radius, install the rip fence as follows. Insert the rip fence into the rectangular hole on the side of the base with the fence guide facing up.
Insert the circular guide pin through either of the two holes on the fence guide. Screw the threaded knob onto the pin to secure the pin. Now slide the rip fence to the desired cutting Cover plate for aluminum base (Optional accessory) 1. Cover plate
radius, and tighten the bolt to secure it in place. Then move the base all the way forward. NOTE: • Always use blades No. B-17, B-18, B-26 or B-27 when cutting circles or arcs. Anti-splintering device for steel base 1 2 008102 2. Aluminum base (optional accessory) 1 2 008100 1. Anti-splintering device 2. Protrusions Use the cover plate when cutting decorative veneers, plastics, etc. It protects sensitive or delicate surfaces from damage. Fit it on the back of the tool base. MAINTENANCE CAUTION: • Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance.
For splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the base all the way forward and insert it between the two protrusions of the base. NOTE: • The anti-splintering device cannot be used when making bevel cuts. Anti-splintering device for aluminum base (Optional accessory) 1. Anti-splintering device 2. Aluminum base 2 1 008101 For splinter-free cuts, the anti-splintering device can be used. To install the anti-splintering device, move the tool base all the way forward and fit it from the back of tool base. When you use the cover plate, install the anti splintering device onto the cover plate. CAUTION: • The anti-splintering device cannot be used when making bevel cuts. • Never use gasoline, benzine, thinner, alcohol or the like. Discoloration, deformation or cracks may result. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. OPTIONAL ACCESSORIES CAUTION: • These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. • Jig saw blades • Hex wrench 3 • Rip fence (guide rule) set • Anti-splintering device • Hose (For vacuum cleaner) • Cover plate (For aluminum base type) NOTE: • Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.
884727G224 Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan makita.com 12
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL