LOREX E861AB (01) PDF Document

It is recommended to connect the LOREX E861AB camera to the NVR or an external PoE switch. If using a DC power adapter (not included) with the camera, a REGULATED power supply is REQUIRED for use with this camera. Use of a non-regulated, non-conforming power supply can damage this product and voids the warranty.

The package contents for the LOREX E861AB 4K Ultra HD Bullet IP Camera include:

4K Ultra HD Bullet IP Camera

Mounting Kit*

Ethernet Extension Cable with Pre-attached RJ45 Cable Gland*

* Per camera in multi-camera packs.

The dimensions are 2.8 inches (70mm) by 7.1 inches (180mm).

Safety precautions include:

Use the camera only with compatible Lorex NVRs.

Read this guide carefully and keep it for future reference.

Follow all instructions for safe use of the product and handle with care.

Use the camera within given temperature, humidity and voltage levels noted in the camera’s specifications.

Do not disassemble the camera.

Do not point the camera directly towards the sun or a source of intense light.

Use only a regulated power supply with the product (optional). Use of a non-regulated, non-conforming power supply can damage the product and void the warranty.

Periodic cleaning may be required. Use a damp cloth only. Do not use harsh cleaners or aerosol cleaners.

The supplied cable is rated for surface mounting only. Cables for in-wall and floor-to-floor installations are sold separately (CMR type). These and other cables are available at lorex.com.

The pre-attached RJ45 cable gland covers the camera’s Ethernet connector and the RJ45 plug to provide weather-resistance and protection from dust, dirt and other environmental contaminants.

To use the RJ45 cable gland:

Twist the RJ45 cable gland barrel securely onto the camera Ethernet connector.

NOTE: The RJ45 cable gland is weather-resistant. Seal the cap with silicone and/or electrical tape for additional sealing if it will be exposed to precipitation regularly.

Optimizing person and vehicle detection accuracy involves:

Angle the camera so that objects of interest appear in the bottom half of the camera image.

Choose a location where objects of interest will be no further than 50ft (~15m) from the camera.

Angle the camera between 30~60° down from the level position.

Install the camera between 8-16ft (2.5-5m) off of the ground.

NOTE: Accuracy of person and vehicle detection will be influenced by multiple factors, such as the object’s distance from the camera, the size of the object, and the height and angle of the camera. Night vision will also impact the accuracy of detection.

Additional installation tips include:

Point the camera where there is the least amount of obstructions (e.g., tree branches).

Install the camera where vandals cannot easily reach.

Secure cabling so that it is not exposed or easily cut.

This camera is rated for outdoor use. Installation in a sheltered location is recommended.

To install the LOREX E861AB camera:

1. Use the included mounting template to mark holes for the screws. Drill holes for the mounting screws. NOTE: Insert the included drywall anchors if you are installing the camera in drywall.

2. Connect cables as shown in the section “Connecting the Camera”.

3. Feed the cable through the mounting surface or cable notch and mount the camera stand to the surface using the provided screws.

4. Use a Philips screwdriver (not included) to loosen the adjustment screw.

5. Adjust the camera position as needed.

6. Tighten the adjustment screw to secure the position.

7. Remove the vinyl film from the camera lens when your installation is complete.

For connection Scenario 1: Connect Cameras to NVR:

Connect the Ethernet cable to the camera. Connect the other end of the Ethernet cable to the NVR’s PoE ports. The camera may take a minute to power up after being connected.

For connection Scenario 2: Connect Cameras to Local Area Network (LAN):

Connect the Ethernet cable to the camera. Connect the other end of the Ethernet cable to a router or switch on your network. See your NVR manual for details on connecting the camera to your NVR using a switch or router.

The maximum cable run distance and number of extensions are detailed in the following table:

You can use a RJ45 coupler or switch (not included) to connect male ends of Ethernet cable together.

To extend the cable run beyond 300ft (91m), a switch will be required (sold separately).

If there is no picture or signal on the LOREX E861AB camera:

Ensure the camera is connected to a compatible NVR supporting 4K camera input. For full camera compatibility, visit lorex.com/compatibility.

The camera may take up to 1 minute to power up after being connected to the NVR. Wait two minutes before following the steps below.

Ensure the camera is connected to your NVR or to your local network.

If you are not using PoE, you must connect the camera to a 12V DC power adapter (not included).

If the camera is connected to the LAN, you must search your network for cameras using the NVR. See the NVR’s instruction manual.

Ensure your NVR is properly connected to a TV/monitor.

There may be an issue with your extension cable run. Connect the camera to the NVR using a different Ethernet cable.

If the picture on the LOREX E861AB camera is too bright:

Ensure your camera isn’t pointed directly at a source of light (e.g., sun or spot light).

Slide the sunshade forward to block excess light.

Move your camera to a different location.

Check the brightness and contrast settings on the NVR.

If the picture on the LOREX E861AB camera is too dark:

If using during the day, the camera may not be getting enough light. Slide the sunshade backwards to let in more light.

Check the brightness and contrast settings on the NVR.

If the night vision is not working on the LOREX E861AB camera:

The night vision activates when light levels drop. The area may have too much light.

Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth.

Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’.

Remove the vinyl film from the camera lens when your installation is complete.

If the picture on the LOREX E861AB camera is not clear:

Check the camera lens for dirt, dust, spiderwebs. Clean the lens with a soft, clean cloth.

Make sure that the cable run is within the limitations specified in the section ‘Cable Extension Options’.

Remove the vinyl film from the camera lens when your installation is complete.

A bright spot in the video when viewing the LOREX E861AB camera at night is typically caused by night vision reflecting when pointing a camera through a window. Move the camera to a different location.

This camera comes with an image sensor that is extra sensitive to light, meaning that the camera stays in color mode at low-light conditions. For instructions on how to make your camera switch to night mode, visit lorex.com, and search for “How do I make my camera switch to night mode?”.

This camera includes an Auto Mechanical IR Cut Filter. When the camera changes between Day/Night viewing modes, an audible clicking noise may be heard from the camera. This clicking is normal, and indicates that the camera filter is working.

You must connect the LOREX E861AB camera to a supporting H.265 NVR to take advantage of H.265 compression. For instructions on enabling H.265 compression, visit lorex.com and search for “How do I enable H.265 compression?”.