LOGITECH ZONE WIRED 2 (01) PDF Document

The following items are included in the box:

1. Headset

2. USB-A adapter

3. Travel bag

4. User documentation

There are two ways to connect the headset to your computer:

1. Plug the USB-C connector directly into the computer USB-C port.

2. Use the provided USB-A adapter to plug the headset into the computer USB-A port.

Note: Only use the provided USB-A adapter with the provided LOGITECH ZONE WIRED 2 headset.

Follow these steps to adjust the headset:

1. Adjust the headset by sliding the earcups up and down the headband.

2. Swivel the earcups so they fit properly on your ears.

3. It may be easier to perform these adjustments while the headset is on your head. Move the earcups up and down until they sit comfortably on your ears.

The microphone boom rotates 270 degrees, allowing it to be worn on either the left or right side. The audio channel will switch automatically depending on the direction you are wearing the microphone.

The microphone boom should be placed close or next to your mouth, aligned with the corner of your mouth.

The LOGITECH ZONE WIRED 2 features several controls for calls, media, volume, and noise cancellation:

Note: Media controls must be enabled through the Logi Tune software. Voice prompts indicate when the microphone is muted or unmuted.

ANC blocks out surrounding noise to help you concentrate on your tasks. You can press the ANC button on the side of the earcup to toggle between ANC and Transparency mode. There will be voice prompts when switching between these modes.

The ANC button can be customized using the Logi Tune app to cycle through up to 5 different modes.

The light indicator on the connector provides status updates for your headset:

Using the Logi Tune software, you can adjust several settings for the LOGITECH ZONE WIRED 2:

Sidetone: This feature allows you to hear your own voice while speaking so you are aware of your volume. A higher number increases external sound, while a lower number decreases it.

Mic EQ: You can adjust your voice to sound brighter or deeper.

Enable EQ for Calls: This allows you to apply equalizer settings specifically to call audio, enabling you to hear callers with deeper bass or crisper treble.

The headset provides three types of protection for safe listening:

Peak limiting: Audio volume is always limited to 100dBA to prevent hearing damage.

Anti-startle protection: This limits sudden audio spikes to avoid acoustic shocks, compliant with the Australian G616 guideline. This applies to call activities only.

Noise exposure over time: It monitors average daily noise levels in calls to ensure they do not exceed a time-weighted average of 85dBA, compliant with the Australian G616 guideline. This applies to call activities only.

When Power Saving Mode is activated via Logi Tune, the headset will automatically turn off Active Noise Cancellation (ANC) and the light indicator after 30 minutes of inactivity to conserve power.

To wake up the headset, join a call, listen to music, or press any button.

The technical specifications for the headset include:

Microphone type: 2 noise-canceling mics with AI-based algorithm and Mic EQ.

Frequency response (headset): 20 Hz to 20 kHz (music mode) and 100 Hz to 8 kHz (talk mode).

Frequency response (microphone): 100 Hz to 8 kHz.

Cable length: 1.9 meters.

Audio compliance: EN 50332-2 compliant.

The physical dimensions of the headset and adapter are as follows:

Headset Height x Width x Depth: 185.2 mm x 183.6 mm x 73.0 mm.

Headset Weight: 223.5 g.

Adapter Height x Width x Depth: 24.5 mm x 15.4 mm x 8.7 mm.

The LOGITECH ZONE WIRED 2 works with common calling applications across almost all platforms and operating systems. It supports Windows, Mac, or Chrome-based computers via a USB-C or USB-A port.