LOGITECH ZONE 950 (02) PDF Document

The following items are included in the box:

1. Headset

2. USB-C receiver

3. USB-A adapter

4. USB-C to C charging cable

5. Travel bag

6. User documentation

To power on the LOGITECH ZONE 950, slide the power switch to the center. Once the device is powered on, the light indicator will turn white.

To power off the device, slide the power switch toward the power icon.

1. USB-C Connection: Insert the receiver directly into the computer USB-C port.

2. USB-A Connection: Insert the USB-C receiver into the USB-A adapter, then insert the adapter into the computer USB-A port.

3. The headset is pre-paired to the receiver it ships with. Simply power on the headset. Once successfully paired, the light indicator on both the receiver and the headset will remain solid white.

4. Ensure that LOGITECH ZONE 950 is selected in your computer sound settings.

1. Slide the power switch to the Bluetooth icon and hold it for 2 seconds. The light indicator will flash blue rapidly.

2. Open the Bluetooth settings on your device.

3. Select LOGITECH ZONE 950 from the list of discoverable devices.

4. Once successfully paired, the light indicator will turn solid white.

1. Adjust the headset by sliding the earcups up and down the headband until they sit comfortably on your ears.

2. Swivel the earcups to better fit the shape of your ear.

3. The microphone boom rotates 270 degrees and can be worn on either the left or right side. The audio channel will switch automatically depending on the direction you are wearing the microphone.

To charge the device, plug the USB-C cable into the port on the bottom of the earcup and the other end into a USB-C charging port on your computer. The light indicator will show a breathing white light during charging and turn solid white when fully charged.

Charging performance:

2 hours of charging fully charges the battery.

5 minutes of charging provides approximately 1 hour of talk time.

The headset can be used with the receiver and Bluetooth paired while charging, or as a corded headset via the USB-C cable while the power is off.

Usage	Action
Answer / End call	Short press Call button
Reject call	2 seconds press Call button
Resume call	Short press Call button
Toggle between ANC and Transparency	Short press ANC button
ANC and Transparency off	2 seconds press ANC button
Play / Pause	Double tap earcup
Track forward	Triple tap earcup
Volume up	Swipe up on earcup
Volume down	Swipe down on earcup
Check connectivity and battery status	Tap and hold earcup for 2 seconds
Mute on/off	Short press Mute button
Trigger voice assistant	2 seconds press (when mic boom is down)

There are 3 ways to mute the microphone:

1. Press the dedicated mute button on the microphone boom.

2. Flip the microphone boom up to mute or down to unmute.

3. Take the headset off to mute and put it back on to unmute (this feature must be enabled in the Logi Tune app).

Voice prompts will indicate “Mute on” or “Mute off” when the status changes.

Light Color	Light Pattern	Status
White	Solid	Power on / Connected to a device / Battery fully charged
White	Pulsing	Battery charging
White	Blinking	Incoming call
Red	Blinking	Low battery
Red	Solid	Mute on
Blue	Flashing	Bluetooth pairing mode
Blue and White	Blinking	Headset firmware updating

Light Color	Light Pattern	Status
White	Solid	Connected / Ongoing call
White	Repeat flashing on and off	Incoming call
Red	Solid	Mute on
Blue	Flashing	Pairing

The LOGITECH ZONE 950 features sensors that detect if the headset is being worn to control the following:

Auto pause/resume: Media streaming will pause when the headset is taken off and resume when put back on.

Answer incoming call: You can answer a call simply by putting the headset on.

Mic mute/unmute: During a call, taking the headset off will mute the microphone, and putting it back on will unmute it.

If audio is unstable due to high wireless density, you can use the LOGITECH ZONE 950 as a corded headset (Audio over USB):

1. Turn off the headset.

2. Connect the headset to your computer using the provided USB-C cable.

3. Ensure LOGITECH ZONE 950 is selected in your computer audio device settings.

Note: The headset will charge in this mode, but button controls may be unavailable.

The LOGITECH ZONE 950 provides three types of protection:

Peak limiting: Audio volume is limited at 100dBA to prevent hearing damage.

Anti-startle protection: Eliminates sudden audio spikes to avoid acoustic shocks (per Australian G616 guidelines). This applies to call activities only.

Noise exposure over time: Protects ears from noise exposure over an 8-hour period with a limit up to 85dBA (per Australian G616 guidelines). This applies to call activities only.

1. Plug the USB-C receiver (or adapter) into the computer USB port.

2. Power on the headset.

3. Open the Logi Tune Desktop application on your computer.

4. Select Zone Receiver from the dashboard.

5. If no headset is shown as connected, click Pair headset.

6. Enter pairing mode on the headset by holding the power switch to the Bluetooth icon for 2 seconds until the light flashes blue rapidly.

7. Once paired, the indicators on both devices will turn solid white.

To reset the headset, power it on, then hold the power button in pairing mode and long press the ANC button for 5 seconds. The reset is successful when the light indicator blinks fast in red and white 3 times and then turns off.

Dimensions:

Headset: 183.9 x 179.1 x 70.0 mm

Headset Weight: 0.23 kg

Receiver: 26.6 x 12.4 x 6.5 mm

Adapter: 24.5 x 15.4 x 8.7 mm

Technical Details:

Microphone type: 5 omnidirectional MEMS

Frequency response (headset): 20 to 20 kHz (music mode), 100 to 8 kHz (talk mode)

Battery type: Built-in lithium ion battery

Battery life (talk time): Up to 15 hrs (ANC on), up to 18 hrs (ANC off)

Battery life (listening time): Up to 22 hrs (ANC on), up to 40 hrs (ANC off)

Bluetooth version: 5.2

Wireless range: Up to 50 m / 170 ft (open field line of sight)

Charging cable length: 1.5 m