LOFREE FLOW LITE84 (01) PDF Document

The specifications for the LOFREE FLOW LITE84 keyboard are as follows:

Number of keys: 84 (Hot-swappable Mechanical Switch)

Numbers of Multifunction Keys: 16

Materials: ABS Body, PBT+ABS Keycaps

Interface Type: C

Mode: Wired/Bluetooth/2.4G

Bluetooth Name: Flow84-L@Lofree

Dimensions: 316.8x138x23.5mm

The diagram of the LOFREE FLOW LITE84 keyboard highlights the following components:

1. Battery Indicator

2. Volume Scroll Wheel

3. Caps Lock Indicator (White) / Status Indicator (Blue)

4. Type-C Interface

5. Mode Switch

6. 2.4G Receiver

The indicator lights on the LOFREE FLOW LITE84 provide information on battery status, caps lock, and connection status.

Battery Indicator:

Charging: Indicator on breathing white

Charged: Indicator always on white

Battery<20%: Indicator on breathing red

Battery<5%: Indicator flashing till off

Caps Lock Indicator / Bluetooth Pairing Indicator:

Caps Lock on: Indicator on white

Caps Lock off: Indicator white light disabled

Bluetooth Pairing: Indicator blinks slowly for 1 minute

Device Switching: Indicator flashes for 3 seconds

After Successful Connection: Indicator keeps on for 3 seconds

During Reconnection: Indicator keeps blinking

After Successful Reconnection: Indicator keeps on for 3 seconds, and then recovers to the previous state

You can use the Volume Scroll Wheel on the LOFREE FLOW LITE84 as follows:

Scroll up for volume up.

Scroll down for volume down.

Press to switch between mute and non-mute.

To use the LOFREE FLOW LITE84 in wired mode, follow these steps:

1. Toggle the mode switch to the Wired setting.

2. Connect the keyboard to the device with the attached Type C cable to complete the wired connection.

To connect your LOFREE FLOW LITE84 keyboard via Bluetooth, follow these steps:

1. Toggle the mode switch to the wireless setting.

2. Long Press Fn+1, Fn+2, or Fn+3 until the indicator blinks slowly on Blue. This makes the keyboard discoverable.

3. On your device, find and pair “Flow84-L@Lofree” from the list of available Bluetooth devices.

4. Once connected, the status indicator will stay on for 3 seconds and then turn off.

To switch between different paired Bluetooth devices, press Fn+1, Fn+2, or Fn+3 on your LOFREE FLOW LITE84. This will switch the keyboard to the corresponding saved device.

To use the 2.4G wireless mode with your LOFREE FLOW LITE84, follow these steps:

1. Take out the 2.4G receiver from the bottom of the keyboard.

2. Insert the 2.4G receiver into the USB port of your device.

3. Toggle the mode switch on the keyboard to the wireless setting.

4. Press Fn+4 for 1 second to enter 2.4G mode.

5. The corresponding 2.4G light will flash slowly. After a successful connection, the blue light will stay on for 3 seconds and then go off.

Note: The keyboard and 2.4G receiver are paired to each other from the factory. To pair the device again, simply insert it. Mac/iOS system devices do not support multimedia functions under a 2.4G/USB connection.

To control the ambient light on the LOFREE FLOW LITE84, press the key combination Fn + the right arrow key (->). This will cycle through the different light modes: Steady, Breathe, and Off.

You can switch the system function key layout on your LOFREE FLOW LITE84 to match your operating system:

Press Fn+N to trigger the corresponding system function key of Windows/Android.

Press Fn+M to trigger the corresponding system function key of Mac/iOS.

The LOFREE FLOW LITE84 features several multifunction key shortcuts. Fn + F1…Del serves as the Multimedia Key.

The following table shows the name and content of hazardous substances in the LOFREE FLOW LITE84 product.

This table is prepared in accordance with the provisions of SJ/T 11364.

The classification and marking of this product was performed in accordance with the EU directive 2011/65/EU and the revised directive 2015/863/EU.

O: Indicates that the said hazardous substance contained in all the homogeneous materials for this component is below the limit requirement in GB/T 26572.

X: Indicates that this hazardous substance contained in at least one of the homogeneous materials used for this part is above the limit requirement in GB/T 26572.

The hazardous substances in the electronic parts of this product will not leak or change under normal use conditions for a period of ten years. During the same period, the electronic components of this product will not cause serious environmental pollution or serious damage to human health or property while the products are being used by the consumer.

According to the Chinese electronic industry standard SJ/T 11364-2014 and related Chinese government regulations, this product and some of its internal or external components may have an environmentally friendly use period mark, depending on the component and component manufacturer, the mark lifespan on the product and its components may vary. The expiration date on the component takes precedence over any conflicted or different UFUP labels on the product.

Yes, please be aware of the following warnings when using the LOFREE FLOW LITE84:

If the battery is not replaced properly, there may be leakage or explosion and personal injury hazards.

Do not use the battery if there is leakage, discoloration, deformation, or any other abnormality.

Do not leave the battery in a discharged or unused state for a long time.

Do not short-circuit the product.

Battery life varies with usage. Used batteries should be disposed of in accordance with local laws or thrown away in trash cans for recycling electronic devices.

If any liquid accidentally enters the product, please immediately disconnect the power supply and remove the product. Continued use of the product may cause fire or electric shock.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.