LINEA DOMO DO7293S (01) PDF MANUAL

LINEA DOMO DO7293S (01) PDF SUMMARY:

What should I do before using the appliance for the first time?

Make sure all packaging materials and promotional stickers have been removed before using the appliance for the first time. Make sure children cannot play with the packaging materials.

---

What should I check before using the appliance?

Before use, check if the voltage stated on the appliance corresponds with the voltage of the power net at your home.

---

What type of socket should I use to connect the appliance?

Always connect the appliance to an earthed socket.

---

What should I do if the cord or plug is damaged?

Never use the appliance when the cord or plug is damaged, after malfunction, or when the appliance itself is damaged. In that case, take the appliance to the nearest qualified service center for check-up and repair.

---

What should I do to avoid accidents when using the appliance?

The manufacturer can not be held responsible for accidents that result from improper use of the appliance or not following the instructions described in the manual.

---

Who should carry out repairs on the appliance?

All repairs should be carried out by the manufacturer or its aftersales service.

---

What should I never do with the appliance, cord, or plug?

Never immerse the appliance, the cord, or the plug in water or any other liquid.

---

What should I do to prevent the risk of electrocution?

To prevent the risk of electrocution, do not use the vacuum cleaner outdoors or on wet surfaces.

---

What should I do to prevent damage when vacuuming?

Remove large and sharp objects from the floor before vacuuming to prevent possible damage.

---

What should I do if I plan not to use the remote control for a long time?

If you will not be using the remote control for a long period of time, remove the batteries.

---

What should I do before using the vacuum cleaner for the first time?

• Put two AAA batteries in the remote control.
• Set the time (see “use/use without remote control/plan: clock”).
• Prior to initial use, charge the robot vacuum cleaner for 5 hours (see “use/charging”).
• Place the signed brushes on the vacuum cleaner. Press on them until you hear a click. The brushes and the machine are marked with L (left) and R (right); make sure they match.

---

How do I install the charging station?

1. Place the charging station on a smooth hard surface, e.g. tiles, parquet, short-haired sturdy carpet, against a wall or cupboard.
2. Make sure that there is an area of at least 1 m free on the left and right sides of the charging station. In front of the charging station, there must be a free area of 2 m (Fig. 1). If this is not the case, it is possible that the vacuum cleaner cannot find the charger when it must charge.
3. Take the adapter, put the plug in the outlet and put the DC plug into the charging station. Always make sure that no cables are in front of or next to the charging station; these could get caught between the wheels or brushes of the vacuum cleaner.

---

How do I turn the machine on?

Turn the machine on with the on switch on the side of the appliance prior to use or charging.

---

When is the machine in standby mode?

The machine is in standby mode when the on switch is on and the machine is in idle state, ready to be used immediately.

---

When is the machine in sleep mode?

When the machine is in sleep mode, you must first activate it before you can start the machine. This is done by pressing the on/off touchscreen button on the machine or with the ON/OFF button on the remote control.

---

How do I activate the machine from sleep mode?

Activate the machine from sleep mode by pressing the on/off touchscreen button on the machine or with the ON/OFF button on the remote control.

---

How does the machine automatically go into sleep mode?

The machine automatically goes into sleep mode after being in standby mode for 15 minutes.

---

How do I manually put the machine into sleep mode?

You can also turn on the mode yourself by pressing and holding the on/off touchscreen button on the machine for 3 seconds.

---

How do I turn off the machine completely?

You can turn off the machine completely by switching off the on switch on the side of the device while in standby mode. The machine turns itself off after being in sleep mode for 15 minutes if no timer has been set.

---

How do I charge the robot vacuum cleaner?

1. Place charging station against the wall and remove obstacles about 1m on either sides and 2m in front of the station.
2. If the robot is powered off, switch on the robot first before charging.
3. Plug one end of the adapter into the robot and the other end into the power socket.
4. Press the “HOME” button on the remote control or robot to operate the robot looking for the charging docking automatically.

---

What does the LED panel show when the robot is charging?

When the robot is charging, the LED panel will gradually show “1111” from left to right.

---

What does the LED panel show when the robot is fully charged?

When charging is over, the LED panel will show “FULL”.

---

What does the robot do when the battery level is low?

• In standby status, the robot will show when the battery level is low.
• In working status, the robot will look for the charging dock automatically when the battery level is low.

---

How long should I charge the robot for the first time?

Please charge the robot for up to 5 hours during the first charging.

---

When should I charge the robot?

Charge the robot as soon as possible when battery capacity is low.

---

What does the robot do when cleaning is finished or the battery is low?

The robot will return to the charging dock automatically when cleaning is finished or battery capacity is low.

---

What should I do if I’m not using the robot for some time?

When you do not use the robot for some time, please fully charge the battery first, then switch off the robot and keep it in a cool but dry place.

---

What should I do if the robot has been put aside for over 3 months?

If the robot has been put aside for over 3 months, please charge the robot for 5 hours first before using it for cleaning.

---

How do I start automatic cleaning without the remote control?

Press the on/off touchscreen button for automatic cleaning. The vacuum cleaner will plot its own path to vacuum the entire area, taking walls, obstacles, and stairs into account.

---

What happens when the machine is finished vacuuming?

When the machine is finished vacuuming, it will automatically return to the charging station. If no charging station is installed, the vacuum cleaner enters standby mode.

---

How do I manually stop the cleaning process?

Touch the on/off touchscreen button to stop cleaning. Turn the device off with the on switch on the side of the machine.

---

How do I send the machine to the charging station for re-charging?

If you wish to charge the vacuum cleaner during use, press the HOME button. The vacuum cleaner will now automatically look for the charging station.

---

Why may the vacuum cleaner not find the charging station?

It is possible that the vacuum cleaner cannot find the charging station because there are too many obstacles around the charging station. Make sure that the free area around the charging station is as large as possible.

---

What happens if the battery is empty?

If the battery is empty, the vacuum cleaner will automatically return to the charging station.

---

How do I set the clock?

1. Press the plan button to set the clock.
2. The hours on the display begin to flash. Set the hours by pressing the home button. Press the power button to confirm.
3. The minutes on the display begin to flash. Set the minutes by pressing the home button. Press the power button to confirm.
4. The home button’s indicator light goes out and the plan button’s light flashes. After 10 seconds, both indicator lights turn on again and your settings are saved.
5. Pressing the plan button during setup will return the device to standby mode and your settings will be cancelled.

---

How do I use the timer to let the robot vacuum automatically?

1. First, set the clock.
2. Press and hold the plan button for 5 seconds and then release.
3. The hours on the display begin to flash. Set the hours by pressing the home button. Press the power button to confirm.
4. The minutes on the display begin to flash. Set the minutes by pressing the home button. Press the power button to confirm.
5. You’ll hear a sound as confirmation. The timer is now set.
6. Pressing the plan button during setup will return the device to standby mode and your settings will be cancelled.

---

How do I disable the programmed timer?

1. Press and hold the plan button for 5 seconds and then release.
2. Set the timer to 00:00 as previously described.
3. You’ll hear a sound as confirmation. The timer is now switched off. The robot will no longer vacuum automatically.

---

How do I start automatic cleaning with the remote control?

Press the on-off button for automatic cleaning. The vacuum cleaner will plot its own path to vacuum the entire area, taking walls, obstacles and stairs into account.

---

How do I select a cleaning program?

1. Use the ON/OFF button to start the vacuum cleaner in automatic cleaning mode.
2. Press the MODE button. Make sure the remote control is aimed at the machine. If the mode has been changed, you will hear a short signal.

---

What are the different cleaning modes?

• MODE 1: spiral. The vacuum cleaner will move in a spiral formation.
• MODE 2: automatic. The vacuum cleaner will plot its own path to vacuum the entire area, taking walls, obstacles and stairs into account.
• MODE 3: corners. The vacuum cleaner will go along the walls and clean the corners as well.
• MODE 4: Zigzag. The vacuum cleaner will make a zigzag movement to vacuum the area. The vacuum cleaner will automatically apply this function if a large open area without obstacles is detected.

---

How do I use the MAX button?

Press the MAX button to vacuum at the maximum suction power. The vacuum cleaner will start cleaning automatically, the movement speed is slow, but the suction power is maximum for thorough cleaning.

---

How do I use the arrows on the remote control?

Use the arrows on the remote control to move the robot vacuum cleaner to determine the starting position.

---

What is the anti-fall system?

The robot vacuum cleaner is equipped with an anti-fall detection. The machine will detect stairs or drops, preventing it from falling.

---

What happens when the vacuum cleaner’s battery dies while vacuuming?

When the vacuum cleaner’s battery dies while vacuuming, it will automatically search for the charging station to charge back up.

---

What does the display show when the vacuum cleaner is in standby mode and the battery is exhausted?

When the vacuum cleaner is in standby mode and the battery is exhausted, [ I I ] appears on the display. Allow the device to charge.

---

What happens when the vacuum is charging on the charging station?

• Display shows flashing ‘1111’: vacuum is charging.
• Display shows ‘FULL’: device is fully charged.
• Display shows ‘Erro’: the power switch must be on to charge.

---

How do I charge the vacuum without a charging station?

Plug the adapter into the contact and insert the DC input into the vacuum.

---

How do I clean the side brushes?

Clean the side brush when it becomes dirty and replace it if it’s damaged. The maximum life span of the side brush is 12 months. Before replacing side brushes, check and ensure that the L/R mark on the side brush match with the L/R mark on the bottom base of the robot.

---

How do I clean the dust bin and filters?

1. Hold the bottom of dust bin, and press down on the button using your thumb to take out of the dust bin.
2. Take out dust bin.
3. After pressing down the button, open the dust bin upper cover.
4. Open dust bin cover and take out the primary filter and HEPA filter.
5. Empty the dust bin.
6. Wash the dust bin and primary filter under tap water, clean the HEPA filter with brush, avoid washing it under water.
7. Assemble primary filter and HEPA filter again into dust bin.

---

How do I clean the canister and filter?

1. Press the button that opens the canister. Remove the canister from the vacuum.
2. Press the open button to open the canister.
3. Remove the HEPA filter, including the holder, from the canister.
4. Empty the canister into the waste bin.
5. Rinse the canister and filter holder under running water. Let them dry before putting them back in place. Clean the HEPA filter with the dust brush.
6. If the HEPA filter is dirty, after about 30 days of use, you can also clean it under running water. Let it dry before putting it back in place.
7. The HEPA filter must be replaced after frequent use. The maximum service life of the filter is approximately 6 months.
8. Replace the HEPA filter and holder in the canister. To do this, first turn the cover to the side.

---

How do I clean the machine?

Clean the side brushes, wheels, sensors and the contacts for charging the battery regularly with a soft cloth.

---

When should I replace the side brushes?

After numerous uses, the side brushes should be replaced. The maximum duration of the brushes is approximately 12 months. The brushes and the machine are marked with L (left) and R (right); make sure they match.

---

What should I never do when cleaning the machine?

Never submerge the machine in water! The sensors may not become wet.

---

How do I clean the rotating floor brush?

Open the cover of the floor brush. Wipe the cover clean with a soft cloth. Remove the rotating floor brush. Rinse the brush under running water. Let it dry before putting it back in place.

---

What should I do if I do not use the device for a long period of time?

• Remove the batteries from the remote control.
• Fully charge the battery, turn off the power switch, and store the device in a dry place.

---

What should I do if the device has not been used for 3 months or more?

If the device has not been used for 3 months or more, charge the battery for 5 hours before using.

---

What should I do if the ‘erro’ code appears on the display while charging?

If the ‘erro’ code appears on the display while charging, make sure that the power switch is on.

---

What should I do for all other error codes?

1. Turn the power off using the power switch.
2. Clean the vacuum and all sensors with a dry, soft cloth.
3. Empty the canister.
4. Make sure that no objects are caught in the floor brush.
5. Place the vacuum on a solid surface.
6. Turn the power back on using the power switch.

---

What should I do if the vacuum still does not work after following the troubleshooting steps?

If the vacuum still does not work, please contact the DOMO after-sales service.