Free English LIEBHERR UWT 1672 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD LIEBHERR UWT 1672 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I install the dust filter on my LIEBHERR UWT 1672?
The supplied dust filter prevents dirt from entering the motor compartment, which reduces refrigeration performance. Therefore, you must always install the dust filter. First, remove the protective film from the dust filter. Next, insert the filter at the bottom and click it into place at the top.
What are the requirements for the plinth panel cut-out section for the LIEBHERR UWT 1672?
The required air flow for the appliance is directed through the plinth. You must use the provided ventilation grille for the ventilation opening. The cut-out section in the plinth panel must be centered in relation to the LIEBHERR UWT 1672. The cut-out dimensions are 540 mm by 85 mm.
What are the installation surface and unit requirements for the LIEBHERR UWT 1672?
To avoid problems when installing the LIEBHERR UWT 1672 and to avoid damage, you must ensure the following: The floor on which the appliance stands must be horizontal and level. Furthermore, the kitchen unit must be aligned horizontally and vertically.
Where should the electrical socket be positioned for the LIEBHERR UWT 1672?
The socket must not be situated behind the LIEBHERR UWT 1672 and must be easily accessible. The free length of the power cord is 2000 mm, so ensure the socket position allows for this.
How do I install the appliance into the kitchen unit for my LIEBHERR UWT 1672?
Follow these steps to install the LIEBHERR UWT 1672:
1. Remove the cover from the appliance housing. Apply the cover strips to the leading edge of the appliance housing on the left and right.
2. Adjust the height of the LIEBHERR UWT 1672 to 4 mm less than the recess height by turning the adjustable feet clockwise. Turn the spanner anticlockwise to raise the appliance front and clockwise to lower it.
3. Slide the appliance into the unit until the front surface of the appliance door is flush with the unit fronts. Ensure the mains cable is not damaged during this process.
4. Screw the LIEBHERR UWT 1672 to the body of the unit at the top left-hand side, then click the cover back into place.
5. Screw the LIEBHERR UWT 1672 to the body of the unit at the bottom on the left and right.
6. Insert the foam moulding approximately 10 mm into the opening in the appliance plinth.
7. Insert the ventilation grille into the plinth panel.
8. Fit the plinth panel. In doing so, the foam moulding is pushed backwards into its final position and must be touching the ventilation grille.
Why is it important to align the LIEBHERR UWT 1672 horizontally and vertically?
The LIEBHERR UWT 1672 must be aligned horizontally and vertically. If the appliance is not level, the main body of the appliance can be deformed, and the door will not close properly.
What is the consequence of not installing the foam moulding on the LIEBHERR UWT 1672?
If the foam moulding is not installed, the LIEBHERR UWT 1672 will not achieve its full refrigeration performance during operation.
How do I adjust the lateral tilt of the door on my LIEBHERR UWT 1672?
If the door on your LIEBHERR UWT 1672 is at an angle, you can adjust it by performing the following: Undo the screws on the hinge bracket and slide the hinge bracket to the right or left as needed, then tighten the screws.
CLICK HERE TO DOWNLOAD LIEBHERR UWT 1672 (01) PDF DOCUMENT