LG SK8Y (02) PDF MANUAL

To reduce the risk of electric shock, do not remove the cover (or back). There are no user-serviceable parts inside. Refer servicing to qualified service personnel.

Do not expose this product to rain or moisture.

Do not install this equipment in a confined space such as a book case or similar unit.

Do not use high voltage products around this product (e.g., electrical swatter). This product may malfunction due to electrical shock.

The apparatus should not be exposed to water (dripping or splashing), and no objects filled with liquids, such as vases, should be placed on the apparatus.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings shall never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to.

No naked flame sources, such as lighted candles, should be placed on the apparatus.

The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

Only use the AC adapter supplied with this device. Do not use a power supply from another device or another manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.

To remove old batteries or the battery pack, follow the assembly steps in reverse order. To prevent contamination of the environment and bring on possible threat to human and/or animal health, the old batteries or the battery pack must be put in an appropriate container at designated collection points. Do not dispose of batteries or the battery pack together with other waste. It is recommended that you use local, free reimbursement systems for batteries or battery packs (may not be available in your area). The batteries or the battery pack should not be exposed to excessive heat such as sunshine, fire or the like.

Remove the battery cover on the rear of the remote control, and insert the battery with + and – matched correctly.

O (Standby): Switches the unit ON or OFF.

VOL (Volume) +/- : Adjusts speaker volume.

F (Function): Selects the function and the input source.

(Mute): Mutes the sound.

(Skip): Skips Fast backward or Forward.

(Play/Pause): Starts playback. / Pauses playback.

SOUND EFFECT: Selects a sound effect mode.

: Adjusts sound level of each speaker.

AV SYNC: Synchronizes the audio and video. / Controls TV remote.

INFO: Displays the input source information. / Displays the connected Bluetooth device name on Bluetooth function.

AUTO VOL: Turns on or off the AUTO VOLUME mode. / Turns on or off the surround sound.

AUTO POWER: Turns on or off AUTO POWER function. / Turns on or off the Bluetooth connection lock.

To turn this function on, press and hold AV SYNC on the remote control for about 3 seconds. “ON – TV REMOTE” appears and you can control this unit by your TV remote control.

To check the status of this function, press and hold AV SYNC.

To turn this function off, press and hold AV SYNC and press it once again while “ON – TV REMOTE” is scrolled.

Supported TV brands: LG, Panasonic, Philips, Samsung, Sharp, Sony, Toshiba, Vizio.

Make sure that the sound output of your TV is set to [External speaker].

Depending on the remote control, this function may not work well.

This function does not operate on LG TV’s magic remote control.

This function may not work well when some TV control functions such as HDMI CEC, SIMPLINK and LG Sound Sync set to ON.

Some remote control may not be supported.

Some remote control may not operate if you press repeatedly the volume button.

Mismatches may occur between the sound of the sound bar and the images of your TV. In this case, this function can adjust the delay time.

1. Press AV SYNC.

2. Use (Skip) to control the time which you can set at between 0 and 300 ms.

Press (Mute) to mute your unit. “MUTE” is displayed in the display window. To cancel it, press (Mute) again on the remote control or change the volume level.

The display window will be darkened automatically if there is no key input for 15 seconds. When you press any button, the display window will brighten.

You can display various information of the input source by pressing INFO.

OPT/ARC/HDMI/PORT.: Audio format

BT (Bluetooth): Connected Bluetooth device name

This unit will turn itself off to save electric consumption when the main unit is not connected to an external device and is not used for 15 minutes.

It will also turn off after six hours if the Main unit is connected to a device using portable input.

When network is connected, the speaker switches to the network standby mode. Then the LED indicator on the unit becomes dimmed in white.

If network is disconnected, the speaker switches to the standby mode. Then the LED indicator on the unit turns red.

This sound bar automatically turns on and off by an input source: Optical, LG TV, Bluetooth or “LG Wi-Fi Speaker” app. This function turns on or off each time you press AUTO POWER.

Turning on: Turning on automatically by this function is supported only on network standby mode except an optical signal. Check dimmed white LED on the unit. When you turn on your TV or an external device connected to this unit, this unit recognizes the input signal and selects the suitable function. You can hear the sound from your device. If you try to connect your Bluetooth device, this unit turns on and the unit will be connected to your Bluetooth device. When you run the “LG Wi-Fi Speaker” app and play music on your smart device that has already been paired, the sound bar is turned on to Wi-Fi function and you can listen to the music through the sound bar.

Turning off: When the TV is off, this sound bar switches to the standby mode.

Notes:

• After the unit is turned on by AUTO POWER function, it will be automatically turned off if there is no signal for a certain period of time from the TV connected by LG Sound Sync (Optical/Wireless).

• After the unit is turned on by AUTO POWER function, it will be automatically turned off if there is no signal for a certain period of time from the external device.

• If you turned off the unit directly, it cannot be turned on automatically by AUTO POWER function. However the unit can be turned on by AUTO POWER function when optical signal comes in after 5 seconds of no signal.

• Depending on the connected device, this function may not operate.

• If you disconnect Bluetooth connection by this unit, some Bluetooth devices try to connect to the unit continually. Therefore it is recommended to disconnect the connection before turning off the unit.

• When you turn on this unit for the first time, status of Auto Power function is turned on.

• To use this function, the main unit must be registered in the paired devices list of the Bluetooth device.

• You can set the AUTO POWER function only when this unit is turned on.

When you turn on your TV or an external device connected by one among Optical or LG Sound Sync (Optical or Wireless), this sound bar changes to the suitable function and you can listen to the sound through it.

When you try to connect your Bluetooth device to this unit, the Bluetooth function is selected. Play your music on the Bluetooth device.

When you connect your portable device using a 3.5 mm stereo cable, this unit changes the function to Portable. You can hear the music from your device.

When you play music by “LG Wi-Fi Speaker” app on your smart device, this sound bar changes the function to WI-FI and you can listen to the music through it.

This system has a number of pre-set surround sound fields. You can select a desired sound mode by using SOUND EFFECT.

Notes:

• Sound effect order may be different depending on the regional option.

• In some of the sound effect modes, there will be no sound or low sound from some of the speakers. It depends on the mode of sound and the source of audio, it is not a defect.

• You may need to reset the sound effect mode, after switching the input, sometimes even after the sound file changed.

• When a source of Dolby Atmos is inputted, sound effect will be changed to DOLBY ATMOS automatically. In this state, even though you press the buttons, such as SOUND EFFECT and AUTO VOLUME, this unit does not respond. And you can see only “NOT SUPPORTED” on the display window.

This unit supports Auto volume function that automatically adjusts the volume level.

When the output sound is too loud or too low, press AUTO VOL on the remote control. So you can enjoy the sound with appropriate levels.

To cancel this function, press the button again while “ON-AUTO VOLUME” is displayed.

You can adjust the sound level of each speaker: Sub Woofer, Treble, Bass, Rear.

1. Press button repeatedly to select the speaker you want to adjust.

2. Press VOL +/- to adjust the sound level.

Note: Adjusting rear speakers level is applied only when the rear speakers are connected.

The speaker switches to the standby mode if there is no music playback or no button operation.

Option 1: If the network is disconnected and there is no music playback and no button operation for 15 minutes, the speaker switches to the standby mode. Then “GOOD-BYE” appears on the display window and the LED indicator on the unit turns red.

Option 2: If you press and hold O on the unit or O on the remote control for about 3 seconds, the speaker switches to the standby mode. Then “GOOD-BYE” appears on the display window and the LED indicator on the unit turns red.

If the Bluetooth standby mode is set to ON, the speaker switches to Bluetooth standby mode when it is turned off.

When you turn on the main unit in the Bluetooth standby mode, Bluetooth and LG TV are able to connect even if the network is not connected.

To set Bluetooth standby mode, adjust the volume level of the unit to minimum. And then, press and hold – on the unit and INFO on the remote control for about 3 seconds. You can see “ON-BT STANDBY” and the unit switches to Bluetooth standby mode.

To cancel this function, press INFO while “ON-BT STANDBY” is scrolled.

Notes:

• If you turn off the unit in the WI-FI function, Bluetooth standby mode does not operate.

• To use this function, you should turn on the AUTO POWER function.

Option 1: When the network is connected but music is not played and buttons are not pressed for 15 minutes, the speaker switches to the network standby mode. Then the LED indicator on the unit becomes dimmed in white.

Option 2: If you press O on the unit or O on the remote control, the speaker switches to the network standby mode. Then the LED indicator on the unit becomes dimmed in white.

If the speaker doesn’t respond, reset the speaker.

Press and hold the button until you hear the beep sound once. You can see “RESET” on the display window. Then all wireless network ports are deactivated and the stored wireless network information is deleted.

You can mount the main unit on a wall. It is difficult to make a connection after installing this unit, so you should connect the cables before installation.

Preparation materials (Not supplied): Wall bracket install guide, Wall bracket, Screws, Screws (A), Wall plug.

1. Match the TV’s BOTTOM EDGE of the Wall bracket install guide with the bottom of the TV and attach it to the position.

2. When you mount it on a wall (concrete), use the wall plugs. You should drill some holes. A guide sheet (Wall bracket install guide) is supplied to drill. Use the sheet to check the point to drill.

3. Remove the Wall bracket install guide.

4. Fix the brackets with screws (A) as shown in the illustration.

5. Put the unit on the brackets to match screw holes on the bottom of the unit.

6. Fix the unit with the screws firmly.

To detach the unit, perform it in reverse order.

Cautions:

• Do not install this unit upside down. It can damage the parts of this unit or be the cause of personal injury.

• Do not hang onto the installed unit and avoid any impact to the unit.

• Secure the unit firmly to the wall so that it does not fall off. If the unit falls off, it may result in an injury or damage to the product.

• When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall.

Note: Screws (A) and Wall Plugs are not supplied for mounting the unit. It is recommended to use Hilti (HUD-1 6 x 30) for mounting.

For the best surround sound, place the speakers as shown in the diagram provided in the PDF.

You can organize the cable with cable ties.

1. Hold the cables together with cable ties as shown in the illustration.

2. Tighten cable ties.

Note: After all connections are completed, you can arrange cables as needed.

Connect the sound bar to the power supply with the supplied AC adapter.

1. Connect the supplied AC power cord to the AC adapter.

2. Connect the AC adapter cable to the DC IN adapter input.

3. Plug the AC power cord into an AC outlet.

Caution: Only use the AC adapter supplied with this device. Do not use a power supply from another device or manufacturer. Using any other power cable or power supply may cause damage to the device and void your warranty.

1. Connect the power cord of the sound bar and the wireless subwoofer to the outlet.

2. Turn on the sound bar. The sound bar and the wireless subwoofer will be automatically connected.

If your connection is not completed, you can check the red LED on the wireless subwoofer and the wireless subwoofer does not make sound. To solve the problem, follow the steps below.

1. Press the Pairing button on the rear of the wireless subwoofer. The green LED on the rear of the wireless subwoofer blinks quickly. (If the green LED does not blink, press and hold the Pairing button.)

2. Turn on the sound bar.

3. Pairing is completed. The green LED on the rear of the wireless subwoofer turns on.

Notes:

• It takes a few seconds (and may take longer) for the main unit and the subwoofer to communicate with each other and make sounds.

• The closer the main unit and the subwoofer, the better the sound quality. It is recommended to install the main unit and the subwoofer as close as possible and avoid the cases below:

  • There is an obstacle between the main unit and the subwoofer.

  • There is a device using the same frequency with this wireless connection such as medical equipment, a microwave or a wireless LAN device.

• Keep the sound bar and the subwoofer away from such devices (e.g., wireless router, microwave oven, etc.) over 1 m (3.3 ft) to prevent wireless interference.

1. Connect the black stripe wire to the terminal marked – (minus) and the other end to the terminal marked + (plus).

2. Connect the wireless receiver and the rear speakers (right, left) with the speaker cables.

Cautions:

• Use the speaker supplied with this unit only. Using any other speaker may cause malfunction.

• Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to -. If the cables are reversed, the sound will be distorted and will lack bass.

Note: You need to purchase the wireless rear speakers kit (SPK8-S) to enjoy surround sound.

1. Connect the power cord to the wireless receiver to the outlet.

2. Turn on the main unit: The sound bar and wireless receiver will be automatically connected. The yellow – green LED on the wireless receiver turns on.

When your connection is not completed, you can see the red LED on the wireless receiver and rear speakers are not made sound. To solve the problem, follow the steps below.

1. Press the PAIRING button on the rear of the wireless receiver. The yellow – green LED on the wireless receiver blinks quickly.

2. Turn on the main unit.

3. Paring is completed. The yellow – green LED on the wireless receiver turns on.

You can enjoy magnificent surround sound for all input sound sources with rear speakers.

If you turn on the surround function, the whole speaker outputs sound. When you turn off the surround function, the speakers output sound as an original input sound channel.

To turn on surround function, press and hold AUTO VOL on the remote control for about 2 seconds and press it once again while “OFF – SURROUND” is scrolled.

To turn off surround function, press and hold AUTO VOL on the remote control for about 2 seconds and press it once again while “ON – SURROUND” is scrolled.

You must affix a ferrite core to reduce or eliminate electrical interference.

1. Pull the stopper [a] of the ferrite core to open.

2. Wind the speaker cables around the ferrite core twice.

3. Close the ferrite core until it clicks.

Notes:

• If there is a strong electromagnetic wave product nearby, interference may occur. Put the main unit and wireless receiver away from there.

• The wireless receiver will automatically switch to standby mode in a few minutes after the sound bar is turned off. When the wireless receiver is in standby mode, the LED will turn on in red.

• When you turn on the sound bar, the wireless receiver will turn on and the LED will change to yellow – green and then the rear speakers will make sound within a few seconds.

• It takes a few seconds (and may take longer) for the main unit and Wireless Receiver to communicate with each other.

• Use the rear speaker at least 30 cm (11.8 inch) away from either a TV screen or PC monitor.

• When the wireless receiver is being connected or disconnected with the main unit, output sound may be interrupted.

• Set the distance between the sound bar and the wireless receiver as close as possible and keep them away from devices (e.g., wireless router, microwave oven, etc.) over 1 m (3.3 ft) to prevent wireless interference.

1. Connect the OPTICAL IN jack on the back of the unit to the OPTICAL OUT jack on the TV using an OPTICAL cable.

2. Select the input source to OPT/HDMI ARC by pressing the F button on the remote or unit repeatedly.

You can see “OPT” on the display window if connecting normally between this unit and your TV.

Notes:

• Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover.

• You can enjoy the TV audio through the speakers of this unit. In the case of some TV models, you must select the external speaker option from the TV menu. (For details, reference your TV user manual.)

• Set up the sound output of the TV to listen to the sound through this unit: TV setting menu -> [Sound] -> [TV Sound output] -> [External speaker (Optical)]

• Details of TV setting menu vary depending on the manufacturers or models of your TV.

• If this unit is connected by OPTICAL and ARC at the same time, the ARC signal is a high priority.

1. Connect your LG TV to the unit by using an optical cable.

2. Set up the sound output of the TV to listen to the sound through this unit: TV setting menu -> [Sound] -> [TV Sound output] -> [LG Sound Sync (Optical)]

3. Turn on the unit by pressing O on the remote control or O on the unit.

4. Select OPT/HDMI ARC function by using F on the remote control or F on the unit until the function is selected.

You can see “LGOPT” on the display window if connecting normally between this unit and your TV.

Note: Details of TV setting menu vary depending on the models of your TV.

1. Turn on the unit by pressing O on the remote control or O on the unit.

2. Select LG TV function by using F on the remote control or F on the unit until the function is selected.

3. Set up LG Sound Sync (Wireless) on the TV. Refer to the TV’s instruction manual.

“PAIRED” appears on the display window for about 3 seconds and then you can see “LG TV” on the display window if connecting normally between this unit and your TV.

Notes:

• If you turned off the unit directly by pressing O (Power), LG Sound Sync (Wireless) will be disconnected.

• If your TV and this unit are connected through LG Sound Sync (Wireless), this unit will be in Network standby mode regardless of the status of network connection when this unit is turned off. Check the dimmed white LED on the unit.

If you connect this unit to a TV that supports HDMI CEC and ARC (Audio Return Channel), you can enjoy the TV audio through the speakers of this unit without connecting the optical cable.

To use this function:

• Your TV must support the HDMI-CEC and ARC function and both must be set to On.

• The setting method of HDMI-CEC and ARC may differ depending on the TV. For details about ARC function, refer to your TV manual.

• You must use an HDMI cable (Type A, High Speed HDMI™ cable with Ethernet).

• You must connect the HDMI OUT on the unit with HDMI IN of the TV that supports ARC function using an HDMI cable.

• You can connect only one Sound bar to a TV compatible with ARC.

1. Connect the HDMI OUT (TV ARC) jack on the back of the unit to the ARC jack on the TV using an HDMI cable.

2. Select the input source to OPT/HDMI ARC by pressing the F button on the remote or unit repeatedly.

You can see “ARC” on the display window if connecting normally between this unit and your TV.

Notes:

• You can enjoy the TV audio through the speakers of this unit. In the case of some TV models, you must select the external speaker option from the TV menu. (For details, reference your TV user manual.)

• Set up the sound output of the TV to listen to the sound through this unit: TV setting menu -> [Sound] -> [TV Sound output] -> [External speaker (HDMI ARC)]

• Details of TV setting menu vary depending on the manufacturers or models of your TV.

• Depending on your LG TV model, you may need to turn on the SIMPLINK function on your LG TV.

• When you return to ARC function from another function, you need to select the input source to OPT/HDMI ARC. Then this unit changes to ARC function automatically.

SIMPLINK is an HDMI-CEC feature that allows some functions of this unit to be controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through an HDMI connection.

Controllable functions by LG TV’s remote control: Power on/off, volume up/down, etc.

Refer to the TV owner’s manual for the details of the SIMPLINK function.

LG TV’s with SIMPLINK function have the logo as shown in the PDF.

Notes:

• Depending on the state of the unit, some SIMPLINK operations may differ from your purpose or not work.

• Depending on a TV or a player which is connected with this unit, SIMPLINK operation may differ from your purpose.

When connecting an HDMI or DVI compatible device, ensure the following:

• Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.

• The connected device’s video input is set correctly for this unit.

• The connected device is compatible with 720 x 576p (or 480p), 1280 x 720p, 1920 x 1080i, 1920 x 1080p video input.

Not all HDCP-compatible HDMI or DVI devices will work with this player. The picture will not be displayed properly with non-HDCP devices.

Notes:

• If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output.

• Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again.

• When the HDMI connection with HDCP is not verified, the TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable.

• If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m (15 ft)).

• You cannot change the video resolution in the HDMI mode. Change the video resolution of the connected component.

• If the video output signal is abnormal when your personal computer is connected to the HDMI IN jack, change the resolution of your personal computer to 576p (or 480p), 720p, 1080i or 1080p.

HDMI cable Checklist: Some HDMI cables have poor signal transmission, which can cause problems with sound and video transmission. Even after HDMI cable connections, if no sound, sound is interrupted, noise occurs from the sound bar and/or no video, or no smooth video on your TV, the HDMI cable may be the problem. Use a cable marked with the premium HDMI certification logo. Also make sure that the cable being used is a certified Type A, Ethernet high-speed HDMI™ cable.

Dolby Atmos gives you an amazing experience with overhead sound, and all the richness, clarity, and power of Dolby sound.

DOLBY ATMOS® is available only in HDMI IN and ARC mode.

To use DOLBY ATMOS® in ARC mode, your TV has to support DOLBY ATMOS®.

It is needed to set up an audio output on external devices (Blu-ray disc player, TV etc.) to “No encoding” such as “Bitstream”, “Auto” or “Bypass.” If you can select an audio output sampling rate, set it to 192 kHz.

1. Connect the HDMI IN jack on the back of the unit to the HDMI OUT jack on the external device such as a Blu-ray disc player, DVD player, etc.

2. Connect the HDMI OUT (TV ARC) jack on the back of the unit to the HDMI IN (ARC) jack on the TV.

3. Set the input source to HDMI or OPT/HDMI ARC. Press repeatedly F on the remote control or F on the unit until the function is selected.

• If you select HDMI, you can hear the sound from the external device. Select it when playing the external device.

• If you select OPT/HDMI ARC, you can hear the sound from your TV. Select it when watching the TV.

You can see “DOLBY ATMOS” on the display window if connecting normally between this sound bar and your TV and DOLBY ATMOS contents is played.

Notes:

• DOLBY ATMOS® supports 2.1 channels (4.1 channels when connected with Rear kit).

• If the sound bar does not have sound or the video on the TV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist.

You can enjoy the sound from the external device which is connected to the HDMI IN jack on this unit.

1. Connect the HDMI IN jack on the back of the unit to the HDMI OUT jack on the audio device such as a Blu-ray disc player, DVD player, etc.

2. Set the input source to HDMI. Press repeatedly F on the remote control or F on the unit until the function is selected.

Connect an optical output jack of external devices to the OPTICAL IN jack.

1. Connect the OPTICAL IN jack on the back of the unit to the optical out jack of your external device.

2. Select the input source to OPT/HDMI ARC by pressing F button on the remote or unit repeatedly.

You can see “OPT” on the display window if connecting normally between this unit and your device.

Note: Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover.

The unit can be used to play music from many types of portable players or external devices.

1. Connect the portable player to the PORTABLE IN connector of the unit.

2. Turn the power on by pressing O (Power).

3. Select the PORT. function by pressing F on the remote control or F on the unit until the function is selected.

4. Turn on the portable player or external device and start playing it.

Using a wired connection provides the best performance, because the attached devices connect directly to the network without radio frequency interference.

1. Connect your speaker to the home router using a LAN cable.

2. You can see the speaker on the screen of your smart device when you open the “LG Wi-Fi Speaker” app.

A wireless router must be connected to the internet.

A smart device such as a smartphone or tablet must be connected to the wireless router via Wi-Fi connection.

Notes:

• Make sure that DHCP’s server is activated on the wireless router.

• If you cannot connect the speaker with your router, go to the router’s settings and then make sure that “Allow wireless client to see each other and access my local network” box is unchecked.

• In a network environment (Router, Internet and Internet Service Provider) that supports both IPv4 and IPv6, the network automatically connects to IPv4 or IPv6 when connecting to the network.

• You can check the network status by selecting the settings of My Speakers ([Settings]>[IP Info.]) on the “LG Wi-Fi Speaker” app.

Through Apple “App Store” or Google “Play Store”:

1. Tap the Apple “App Store” icon or Google “Play Store” icon.

2. Type in “LG Wi-Fi Speaker” in the search bar and tap “Search.”

3. Select “LG Wi-Fi Speaker” in the search result list to download.

Notes:

• “LG Wi-Fi Speaker” app will be available in the following software versions: Android OS: Ver 5.0 (or later), iOS: Ver 10 (or later).

• Depending on the device, “LG Wi-Fi Speaker” app may not work.

When you launch the “LG Wi-Fi Speaker” app for the first time, the terms of use and Chromecast Service appear on the screen.

1. Check the contents of the terms of use and select [Agree and start].

2. Check the contents of the Chromecast Service and select [Agree and start].

Preparation:

• For Simple Connection, Wi-Fi network condition is needed.

• Make sure that the Bluetooth setting on your smart device is on.

• Select WI-FI function by using F on the remote control or F on the speaker.

Note: Simple Connection is supported by Bluetooth Ver 4.0 (or higher).

1. Check the position and condition of the speaker and select [Next].

If you use an Android device, Location authorization is needed. Allow Location authorization. And then press [Next] again.

2. Then you can see the available speaker to connect.

• Select [] if the desired speaker doesn’t appear.

• Select [] to check the speaker with a beep sound.

• If the search failed, select [Retry] to search your speaker again or connect the speaker manually.

3. Select the speaker to connect by checking [] and [Next].

4. If you have a password for your network, the security screen appears on your smart device. Enter your password and tap [Next].

5. Tap [OK] to finish making the connection.

When the simple connection is unavailable between your speaker and smart device, you can connect it manually.

1. Select [Manual setup] to connect the speaker manually.

2. Check the position and condition of the speaker and select [Next].

3. This step is only for iOS devices. Turn on Wi-Fi setting on your iOS device and choose [LG_Speaker_Setup_XXXX] and then go back to “LG Wi-Fi Speaker” app.

4. Enter your password and tap [Next].

Then your smart device is searching for the available speaker to connect.

5. Tap [OK] to finish making the connection.

With the “LG Wi-Fi Speaker” app, you can play music from your smart device.

Preparation:

1. Check the network connection with the speaker.

2. To use the speaker, you must download and install the “LG Wi-Fi Speaker” app.

1. Launch the “LG Wi-Fi Speaker” app on your smart device. [My Speakers] appears.

2. Tap the menu button.

3. The side menu appears, displaying:

• [My Speakers] – Displays the connected speaker.

• [My Phone] – Displays the songs on this smart device.

• [Music Server] – Displays the songs on the connected devices (Media server).

• [Playlist] – Displays the playlists.

• [Settings] – Displays the application settings.

Playing a song:

1. Select [My Phone] or [Music Server] on the side menu.

2. You can see songs on your smart device or music server. Select a song to play.

In [My Phone] menu, the songs are sorted by [Album], [Artists], [Songs], [Genres] and [Folders] (Android device) or [iPhone Playlist] (iOS device).

In [Music Server] menu, the connected servers appear.

3. Tap the cast button and select the speaker. You can listen to music through the connected speaker with Chromecast.

On the song list of [My Phone] or [Music Server], tap the options button (three dots) of the desired song. The pull-down menu appears:

• [Play next] – Selects music to play next.

• [Add to queue] – Adds to the queue list.

• [Add to playlist] – Adds to a desired playlist.

Note: Depending on your wireless environment, playing a song with the speaker may not work smoothly.

You can enjoy music to suit your taste by making Playlists.

1. On the song list of [My Phone] or [Music Server], tap the options button (three dots) of the desired song and [Add to playlist].

2. The [Add to playlist] window appears. Select a playlist to add the song. If you want to make another playlist, select [Make a new].

You can confirm and adjust various information on the playback screen.

The playback screen displays:

• Cast button – Casts music to the connected speaker by Chromecast and stops casting the music.

• Edit playlist button – Edits the current playlist.

• Volume adjustment – Adjusts the volume level of the smart device or the volume of Chromecast.

• Sound effect adjustment – Adjusts the sound effect.

Playback controls:

• Pause button – Pauses playback.

• Play button – Starts playback.

• Skip buttons – Skips fast backward or forward.

• Repeat button – Repeats the desired contents. Every time you click it, the state changes in Repeat One, Repeat All, Repeat Off order.

• Shuffle button – Shuffles the music on the list. Music will be played in random order.

• Song information – Displays information about the currently playing song.

Note: The cast button is disabled when you listen to music by your smart device or listen to music from speakers grouped with the [Google Home] app.

You can select a desired sound mode by tapping the sound effect button. The displayed items for the equalizer may be different depending on the connected speaker, sound sources and effects.

1. During playback, tap the sound effect button.

2. Select the sound effect using the left and right arrows and tap [OK].

You can customize the sound effect by using the sound effect button to adjust Treble and Bass value.

Notes:

• When you listen to music with the smart device’s speaker, the sound equalizer is not supported.

• Depending on the connected speaker, the displayed sound effect may differ.

You can set up settings for the connected speaker. On the [My Speakers] screen, select the settings icon to set up the connected speaker settings.

The settings include:

• [Name Change] – Renames the speaker.

• [Sound Effect] – Selects a sound effect mode.

• [Night] – Turns on or off Night Mode function.

• [DRC] – It reduces the volume of loud sounds or amplifies quiet sounds. (Dolby Digital only) Turns on or off DRC function.

• [Auto Volume On/Off] – Turns on or off Auto Volume function.

• [AV Sync] – Adjusts the audio and video Synchronization.

• [Woofer level] – Adjusts Woofer level.

• [Rear speaker output] – Selects the rear speaker output.

• [Rear speaker level] – Adjusts Rear speaker level.

• [Overhead speaker volume] – Adjusts Overhead speaker volume level.

• [Using the TV remote control] – Adjusts some functions of the speaker with your TV remote control.

• [Auto Power On/Off] – Turns on or off Auto Power function.

• [Bluetooth standby mode] – Turns on or off Bluetooth standby mode.

• [Bluetooth connection restriction] – It enables you to connect a Bluetooth device only on Bluetooth or LG TV function.

• [Sleep timer] – Turns off by itself after the time set.

• [Reset settings] – Resets the speaker settings except network information.

• [Software version information] – Displays the current Software version information and updates the software to the latest version.

• [IP Info.] – Shows the IP address of the speaker.

• [Share usage data] – Selects whether to send Chromecast built-in usage data and crash reports to Google.

• [Learn about Chromecast built-in Privacy] – Shows the Privacy policy of Chromecast.

Note: You cannot see some menus depending on the connected device.

Select [Settings] on the side menu of the “LG Wi-Fi Speaker” app. The settings of the “LG Wi-Fi Speaker” app appear.

Settings include:

• [Participate in user enhancement] – Allows sending user logs for service quality enhancement.

• [Chromecast] – Displays the Chromecast menu.

• [App version information] – Displays this application version information.

• [Terms of Service] – Displays Terms of Service.

• [Open source license] – Shows LGE Open Source Software Notice.

The [Chromecast] menu includes:

• [Learn how to cast] – Shows how to use Chromecast.

• [Cast groups] – Select [Learn about Cast Groups] or [How to cast to a group] to show the selected information.

• [Chromecast built-in open legal documents] – Select [Google Terms of Service], [Google Privacy Policy] or [Open source licenses] to show the selected information.

• [Time zone] – Sets time zone.

Note: To use Cast Groups, install the [Google Home] application. Download the application from Apple “App Store” or Google “Play Store”.

The [Time Zone] menu includes:

• Automatic Time zone – Offers to use network provided time.

• Set Time Zone – If you deselect [Automatic Time zone], you can select your time zone yourself.

Available File extensions: “mp3”, “wma”, “flac”, “aac”, “ogg”, “wav”, “m4a”, “aiff”

Sampling frequency: within 32 to 48 kHz (mp3, wma), up to 192 kHz/24 bit (flac)

Bit rate: up to 320 kbps (mp3, wma)

• The file requirements are not always compatible. There may have some restrictions by file features and media server’s ability.

• Some wav files are not supported on this speaker.

• Depending on the types of file or ways of recording, it may not play back.

• Some DRM-loaded files are not supported on this speaker.

• The types of supported files may differ depending on the operating system and/or the manufacturer of the smart device and PC.

When shipping the speaker: Please save the original shipping carton and packing materials. If you need to ship the speaker, for maximum protection, re-pack the speaker as it was originally packed at the factory.

Keeping the exterior surfaces clean:

• Do not use volatile liquids such as insecticide spray near the speaker.

• Wiping with strong pressure may damage the surface.

• Do not leave rubber or plastic products in contact with the speaker for a long period of time.

Cleaning the speaker: To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution. Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the speaker.

Bluetooth is a wireless communication technology for short-range connection.

The sound may be interrupted when the connection is interfered by other electronic waves or when you connect the Bluetooth in other rooms.

Connecting individual devices under Bluetooth wireless technology does not incur any charges. A mobile phone with Bluetooth wireless technology can be operated via the Cascade if the connection was made via Bluetooth wireless technology.

Available Devices: Smart phone, MP3, Notebook, etc.

Version: 4.0

Codec: SBC, AAC

Bluetooth profiles: To use Bluetooth wireless technology, devices must be able to interpret certain profiles. This speaker is compatible with the following profile: A2DP (Advanced Audio Distribution Profile)

Listening to Music of a Bluetooth Device:

Before you start the pairing procedure, make sure that the Bluetooth feature on your smart device is turned on. Refer to your Bluetooth device’s user guide. Once a pairing operation is performed, it does not need to be performed again.

1. Select the Bluetooth function by using F on the remote control or F on the unit until the function is selected. “BT” and then “READY” appears in the display window.

2. Operate the Bluetooth device and perform the pairing operation. When searching for this speaker on your Bluetooth device, a list of the devices found may appear in the Bluetooth device display depending on the type of Bluetooth device. Your speaker appears as “LG SK8Y (XX:XX).”

3. Select “LG SK8Y (XX:XX).”

Notes:

• XX:XX means the last four digits of the address. For example, if your unit has a MAC address such as 20:C3:8F:C9:31:55, you will see “LG SK8Y (31:55)” on your Bluetooth device.

• Depending on the Bluetooth device type, some devices have a different pairing way. Enter the PIN code (0000) as needed.

• When this unit is successfully connected with your Bluetooth device, “PAIRED” -> your device’s name -> “BT” appears on the display window.

• If it is unavailable to display the device name on the unit, “-” will be displayed.

• To check the connected device’s name, press INFO on the remote control. The connected Bluetooth device’s name is displayed.

• To play music on your Bluetooth device, refer to your Bluetooth device’s user guide.

• According to your Bluetooth device’s volume level, the volume level of Bluetooth will be adjusted.

• When using Bluetooth technology, you have to make a connection between the unit and the Bluetooth device as close as possible and keep the distance. However it may not work well in the case below: There is an obstacle between the unit and the Bluetooth device. There is a device using the same frequency with Bluetooth technology such as medical equipment, a microwave or a wireless LAN device.

• This unit supports Bluetooth auto pairing. However, it does not operate in the case below: When you restart this unit. When you disconnect this unit by yourself. When you disconnect this unit on the connected Bluetooth device.

• The sound may be interrupted when the connection is interfered with by some other electronic wave.

• You cannot control the Bluetooth device with this unit.

• Pairing is limited to “One” Bluetooth device. Multi-Pairing is not supported.

• Depending on the type of the device, you may not be able to use the Bluetooth function.

• You can enjoy using Bluetooth when using Phone, MP3, Notebook, etc.

• The more distance between the unit and the Bluetooth device, the lower the sound quality becomes.

• The Bluetooth connection will be disconnected when the unit is turned off or the Bluetooth device gets too far from the unit.

• If the Bluetooth connection is disconnected, connect the Bluetooth device again.

• When a Bluetooth device is not connected, “READY” appears in the display window.

• If you set the WI-FI function in the state of unconnected network, Bluetooth and Wireless TV Sound Sync may not be connected.

• If you change to another function after connecting a Bluetooth device, the Bluetooth connection will be disconnected. And if you return to the Bluetooth function, the Bluetooth connection will be connected automatically.

You can limit Bluetooth connection to only BT (Bluetooth) and LG TV functions to prevent unintended Bluetooth connections.

To turn on this function, press and hold AUTO POWER on the remote control for about 2 seconds in BT (Bluetooth) function and press it once again while “OFF – BT LOCK” is scrolled. Then you can limit the Bluetooth connection.

To turn off this function, press and hold AUTO POWER on the remote control for about 2 seconds in BT (Bluetooth) function and press it once again while “ON – BT LOCK” is scrolled.

Note: Even if you set up the BT LOCK function to On, this sound bar turns on by the Auto Power function. Turn off the Auto Power function to prevent it.

Possible causes and solutions:

• Turn off the power of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and turn them on again.

• Disconnect the power cord of this unit and the connected external device (TV, Woofer, DVD-player, Amplifier, etc.) and then try connecting again.

• Previous setting may not be saved when device power is shut off.

Possible causes and solutions:

• Is the power cord plugged into the outlet? Connect the power plug to the outlet.

Possible causes and solutions:

• Is the volume set to minimum? Adjust the volume.

• When you are using a connection with an external device (set top box, Bluetooth device etc.), adjust the volume level of the device.

• Is the mute function activated? Press or adjust the volume level to cancel the mute function.

• Is the function selected properly? Check the input source and select the correct input source.

Possible causes and solutions:

• Is the subwoofer plugged in? Plug the power cord of the subwoofer into the wall outlet securely.

• Is pairing between the unit and the subwoofer disconnected? Connect the unit and the subwoofer.

Possible causes and solutions:

• Is the remote control too far from the unit? Operate the remote control within about 7 m (23 ft).

• Is there an obstacle in the path of the remote control and the unit? Remove the obstacle.

• Are the batteries in the remote control exhausted? Replace the batteries with new ones.

Possible causes and solutions:

• Check the connection of the external device such as TV, DVD/Blu-Ray player or Bluetooth device.

• Check the state of SIMPLINK on your LG TV and turn off SIMPLINK.

• Depending on the connected device, this function may not operate.

Possible causes and solutions:

• Check whether your LG TV supports LG Sound Sync.

• Check connection of LG Sound Sync.

• Check sound setting of your TV and this unit.

Check the details below and adjust the unit accordingly:

• Switch the state of DRC function to [OFF] by using “LG Wi-Fi Speaker”.

• With the sound bar connected with TV, change the AUDIO DIGITAL OUT setting on TV Setup Menu from [PCM] to [AUTO] or [BITSTREAM].

• With the sound bar connected with Player, change the AUDIO DIGITAL OUT setting on Player Setup Menu from [PCM] to [PRIMARY PASS-THROUGH] or [BITSTREAM].

• Change Audio DRC setting on the connected device setup menu to [OFF] state.

• Make sure Night Mode is not On. Turn [OFF] Night Mode.

Possible causes and solutions:

• Turn off the Bluetooth connection lock function.

Possible causes and solutions:

• The wireless communication may be interrupted from household devices that are using radio frequencies. Move the speaker away from them.

Possible causes and solutions:

• The firewall or anti-virus software on your media server is running. Turn off the firewall or anti-virus software running on your media server.

• Make sure that the speaker is connected to the same network that your media server is connected.

Possible causes and solutions:

• Is the “LG Wi-Fi Speaker” plugged in? Plug in the “LG Wi-Fi Speaker”.

• Is the LAN cable connected to the wireless router and the “LG Wi-Fi Speaker” properly? Connect the LAN cable to the LAN port on the back of the “LG Wi-Fi Speaker” and to your wireless router.

• If you restart the router? You need to turn the speaker’s power off and on again.

• If you install a new router. You need to perform a factory set and setup the network connection for the speaker.

Possible causes and solutions:

• Does an error occur when accessing the app? Make sure that your smart device is compatible with the app.

• Make sure that the “LG Wi-Fi Speaker” app is the latest version.

• Make sure that the speaker’s front LED turns from red to white.

Possible causes and solutions:

• Wireless may not operate normally in weak signal areas.

• Please install the device close enough to the wireless subwoofer.

• Do not install the device on metal furniture for optimum performance.

Possible causes and solutions:

• When any part of your body contacts the transceiver of the Bluetooth device or sound bar.

• When there is an obstacle or wall or the device is installed in a secluded spot.

• When there is a device (a wireless LAN, medical equipment or a microwave) using the same frequency, make the distance between the products as far away as possible from each other.

• When connecting the device to the Bluetooth device, make the distance between the products as close as possible to each other.

• When the device gets too far from the Bluetooth device, the connection is disconnected and malfunction may occur.

Unplug the power cord and plug it in again. If that doesn’t work, press and hold the WiFi button on the sound bar until you hear the beep sound once. You can see “RESET” on the display window.

Unplug the power cord and plug it in again. If that doesn’t work, press and hold the WiFi button on the sound bar until you hear the beep sound once. You can see “RESET” on the display window.