LG 70UK6570PUB (01) PDF Document

For the LG 70UK6570PUB, the term “LED TV” signifies that it is an LCD screen that utilizes LED backlights.

Please follow these safety instructions when using your LG 70UK6570PUB:

• Read and keep these instructions.

• Heed all warnings and follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

• Do not defeat the safety purpose of the polarized or grounding-type plug.

• Protect the power cord from being walked on or pinched.

• Only use attachments/accessories specified by the manufacturer.

• Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. Use caution when moving the cart/apparatus combination to avoid injury from tip-over.

• Unplug this apparatus during lightning storms or when unused for long periods of time.

• Refer all servicing to qualified service personnel.

To prevent the spread of fire, keep candles or other items with open flames away from the LG 70UK6570PUB at all times.

Do not place the TV and/or remote control in the following environments:

• Keep the product away from direct sunlight.

• An area with high humidity such as a bathroom.

• Near any heat source such as stoves and other devices that produce heat.

• Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

• An area exposed to rain or wind.

• Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus.

• Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

• Do not install in excessively dusty places.

Failure to follow these guidelines may result in fire, electric shock, combustion/explosion, malfunction, or product deformation.

• Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

• Do not install the product on a carpet or cushion.

• Do not block or cover the product with cloth or other materials while the unit is plugged in.

• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

• When mounting on a table or wall, leave a minimum of 10 cm (4 inches) of space from the wall for proper ventilation.

• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

• Do not move the TV whilst the power cord is plugged in.

• Do not use a damaged or loosely fitting power cord.

• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

If any of the following occur, unplug the product immediately and contact your local customer service:

• The product has been damaged.

• If water or another substance enters the product (like an AC adapter, power cord, or TV).

• If you smell smoke or other odors coming from the TV.

• During lightning storms or when unused for long periods of time.

• Store the accessories (battery, etc.) in a safe location out of the reach of children.

• Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.

• Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak.

• Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution.

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation:

• It is recommended to move the TV in the box or packing material that the TV originally came in.

• Before moving or lifting the TV, disconnect the power cord and all cables.

• When holding the TV, the screen should face away from you to avoid damage.

• Use at least two people to move a large TV. When transporting by hand, hold the TV with one hand on the top and one on the bottom of the frame.

• When transporting the TV, do not expose it to jolts or excessive vibration.

• Keep the TV upright; never turn it on its side or tilt it.

• Be careful not to damage the protruding buttons.

• Avoid touching the screen at all times, as this may result in damage to the screen.

• Do not place the product on the floor with its front facing down without padding.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. This may result in electric shock or product damage.

When cleaning, be careful not to allow any liquid or foreign objects to enter the gap between the upper, left or right side of the panel and the guide panel.

• Make sure to wring any excess water or cleaner from the cloth.

• Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

• When the TV is turned on for the first time after being shipped from the factory, initialization may take approximately one minute.

• The On Screen Display (OSD) may differ slightly from that shown in the manual.

• Available menus and options may differ from the input source or product model.

• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches) thick and 18 mm (0.7 inches) wide.

• Use a certified cable with the HDMI logo attached. If you do not use a certified HDMI cable, the screen may not display or a connection error may occur.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

When attaching the stand, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

To prevent the TV from tipping over, you can secure it to a wall using eye-bolts and brackets.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts already in the eye-bolt positions, remove them first.

2. Mount the wall brackets with bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Note: Use a platform or cabinet that is strong and large enough to support the TV securely. Brackets, bolts, and ropes are not provided.

The wall mounting specifications for the LG 70UK6570PUB are as follows:

• VESA (A x B): 600 x 400 mm

• Standard screw: M8

• Number of screws: 4

• Optional Wall mount bracket: LSW640B

When mounting, make sure not to install the TV by hanging the power and signal cables on the back. Also, do not install the TV on a wall if it could be exposed to oil or oil mist, as this may cause damage and lead to it falling.

The following audio formats are supported over HDMI, depending on the model:

• DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz)

• DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz)

• True HD (48 kHz)

• Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz)

• PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)

To enable or disable this feature, navigate to: Settings → Picture → Additional Settings → HDMI ULTRA HD Deep Color.

• On: Supports 4K @ 60 Hz (4:4:4, 4:2:2, 4:2:0)

• Off: Supports 4K @ 60 Hz 8 bit (4:2:0)

If the device connected to the input port also supports ULTRA HD Deep Color, your picture may be clearer. If the device doesn’t support it, it may not work properly. In that case, connect the device to a different HDMI port or change the TV’s setting to off.

• Supported external devices include Blu-ray players, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PCs, and gaming devices.

• Connect external devices to the TV regardless of the order of the TV port.

• If you connect a gaming device, use the cable supplied with the gaming device.

• In PC mode, noise may be associated with resolution, vertical pattern, contrast, or brightness. If noise is present, change the PC output to another resolution, change the refresh rate, or adjust brightness and contrast in the PICTURE menu until the picture is clear.

• Some USB Hubs may not work. If a USB device connected through a USB Hub is not detected, connect it directly to the USB port on the TV.

• When connecting via a wired LAN, it is recommended to use a CAT 7 cable.

You can operate the TV functions using the single button on the unit.

Basic Functions:

• Power On: Press the button.

• Power Off: Press and hold the button.

• Menu Control: Press the button when the TV is on.

• Menu Selection: Press and hold the button to select a menu item.

Adjusting the Menu:

When the TV is turned on, press the button one time to access the menu. You can then press the button repeatedly to cycle through the menu items:

• Turns the power off.

• Changes the input source.

• Scrolls through the saved channels.

• Adjusts the volume level.

How to register the Magic Remote Control:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) button on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the BACK and HOME buttons at the same time for five seconds to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button will let you cancel and re-register the Magic Remote at the same time.

The following are the functions for the Magic Remote buttons. To use a button marked with an asterisk (*), press and hold for more than 3 seconds.

• POWER: Turns the TV on or off.

• STB PWR: Turns your set-top box on or off (when added to the universal remote control).

• Number buttons: Enters numbers.

• – (Dash): Inserts a dash between numbers.

• LIST: Accesses the saved channel list.

• (Screen Remote): Displays the Screen Remote. Also accesses the Universal Control Menu in some regions.

• * (Screen Remote): Enables SAP (Secondary Audio Program) Feature.

• QUICK ACCESS*: Access an application or Live TV channel registered to a number button.

• VOL +/-: Adjusts the volume level.

• (MUTE): Mutes all sounds.

• * (MUTE): Accesses the Accessibility menu.

• CH ^/v: Scrolls through the saved channels.

• (Voice recognition): Press and hold to speak a command (network connection required).

• (HOME): Accesses the Home menu.

• * (HOME): Shows the previous history.

• Wheel (OK): Press the center to select a menu. Use the wheel to change channels.

• (up/down/left/right): Scrolls the menu. If pressed while the pointer is in use, the pointer will disappear.

• BACK: Returns to the previous level.

• BACK*: Clears on-screen displays and returns to the last input viewing.

• GUIDE: Displays the program event guide.

• 1, 2 Streaming Service buttons: Connects to the specific video streaming service.

• (INPUT): Changes the input source.

• * (INPUT): Displays all the lists of external inputs.

• (Q. Settings): Accesses the Quick Settings.

• * (Q. Settings): Displays the All Settings menu.

• Colored buttons: Access special functions in some menus.

• Media control buttons: Control media contents.

• LIVE ZOOM: Zooms in on a selected area to view it in full screen.

• FOCUS*: Zooms in on the area where the remote control is pointed.

• Check if anything, such as tape, has been placed over the receiver on the TV.

• Check if there is any obstacle between the TV and the remote control.

• Replace the batteries with new fresh ones.

• Check if the product is turned on.

• Check if the power cord is connected to a wall outlet.

• Check if there is a problem in the wall outlet by connecting other products.

• Check the power control settings. The power supply may be interrupted.

• Check if the auto-off function is activated in the settings menu.

• If there is no signal while the TV is on, it will turn off automatically after 15 minutes of inactivity.

• If the TV feels cold to the touch, there may be a small flicker when it is turned on. This is normal.

• Some minute dot defects (tiny red, green, or blue spots) may be visible on the screen. However, they have no adverse effect on the TV’s performance.

• Avoid touching the LCD screen or holding your finger(s) against it for long periods of time, as this may produce temporary distortion effects.

• This panel is an advanced product that contains millions of pixels. In a very few cases, you could see fine dots that are deactivated pixels; this does not affect the performance and reliability of the TV.

• Displaying a still image for a prolonged period may cause image sticking (burn-in). Avoid displaying a fixed image on the TV screen for an extended length of time.

• Cracking noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

• Electrical circuit humming/panel buzzing: A low-level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate the product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

You can connect the USB to Serial converter/RS-232C input jack to an external control device (like a computer or A/V control system) to control the TV’s functions externally. The TV supports PL2303 chip-based USB to serial converters.

Connection Types:

• USB to Serial converter with USB Cable: Connect the converter to the PC and the USB cable from the converter to the TV’s USB IN port.

• RS-232C with RS-232C Cable: Use a D-Sub 9pin female-to-female RS-232C cable to connect the PC’s serial port to the TV’s RS-232C IN port.

RS-232C 3-Wire Configuration:

• PC (RXD) Pin 2 to TV (TXD) Pin 2

• PC (TXD) Pin 3 to TV (RXD) Pin 1

• PC (GND) Pin 5 to TV (GND) Pin 3

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General → About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number (from 1-99) and select CLOSE.

5. When you are finished, press EXIT.

(*Path may depend on model)

• Baud rate: 9600 bps (UART)

• Data length: 8 bits

• Parity: None

• Stop bit: 1 bit

• Communication code: ASCII code

• Use a crossed (reverse) cable.

Transmission Protocol:

[Command1][Command2][ ][Set ID][ ][Data][Cr]

• [Command 1]: First command (j, k, m, or x).

• [Command 2]: Second command.

• [Set ID]: The ID number of the monitor to control (1-99). If ‘0’ is used, every connected set is controlled. It is indicated as Hexadecimal (0x00 to 0x63) in transmission protocol.

• [Data]: Hexadecimal command data. Transmit ‘FF’ to read the status of a command.

• [Cr]: Carriage Return (ASCII code ‘0x0D’).

• [ ]: Space (ASCII code ‘0x20’).

OK Acknowledgement:

[Command2][ ][Set ID][ ][OK][Data][x]

The TV sends this acknowledgement when it receives normal data. If the data was in read mode, it returns the current status data.

Error Acknowledgement:

[Command2][ ][Set ID][ ][NG][Data][x]

The TV sends this acknowledgement for abnormal data or communication errors. Data 00 indicates an Illegal Code.

The command to control power is ‘ka’.

Transmission: [k][a][ ][Set ID][ ][Data][Cr]

• Data 00: Power Off

• Data 01: Power On

To check power status:

Transmission: [k][a][ ][Set ID][ ][FF][Cr]

The TV will respond with its current power status (00 for Off, 01 for On).

The command to adjust aspect ratio is ‘kc’.

Transmission: [k][c][ ][Set ID][ ][Data][Cr]

Data Values:

• 01: Normal screen (4:3)

• 02: Wide screen (16:9)

• 04: Zoom

• 06: Set by Program/Original

• 09: Just Scan

• 0B: Full Wide

• 10 to 1F: Cinema Zoom 1 to 16

Volume Mute (Command: ke)

• Transmission: [k][e][ ][Set ID][ ][Data][Cr]

• Data 00: Volume mute on (Volume off)

• Data 01: Volume mute off (Volume on)

Volume Control (Command: kf)

• Transmission: [k][f][ ][Set ID][ ][Data][Cr]

• Data: Min 00 to Max 64 (Hexadecimal)

These key codes are used with the ‘mc’ command for external control.