LG 65UN8050PUD (02) PDF Document

When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs.

Do not press or put stress on the front panel of the TV. Otherwise, this may result in product damage, fire hazard or injury.

When transporting the LG 65UN8050PUD by hand, hold the TV as shown in the manual illustrations: Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV, do not expose the TV to jolts or excessive vibration.

When transporting the TV, keep the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

1. Lift and tilt the TV into its upright position on a table. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

2. Connect the power cord to a wall outlet.

Note: Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product.

If you install the TV on a stand, you need to take actions to prevent the product from overturning.

Do not use any unapproved items to ensure the safety and product life span.

Make sure that the screws are fastened tightly. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not fasten the screws with excessive force otherwise they may strip and become loose.

The VESA dimensions (A x B) for the LG 65UN8050PUD are 300 x 300 mm.

The standard screw size is M6.

The number of screws required is 4.

The optional wall mount bracket model is OLW480B.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Connect an antenna, cable, or cable box to the TV while referring to the illustrations in the manual. The RF cable is optional.

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

DTV Audio Supported Codec: MPEG, Dolby Digital.

When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

Supported HDMI Audio Formats: True HD (48 kHz), Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz), PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz).

To adjust HDMI Ultra HD Deep Color:

Go to [Settings] -> [Picture] -> [Additional Settings] -> [HDMI Ultra HD Deep Color].

On: Support 4K @ 50 / 60 Hz (4:4:4, 4:2:2, 4:2:0).

Off: Support 4K @ 50 / 60 Hz (4:2:0).

If the device connected to Input Port also supports Ultra HD Deep Color, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI Ultra HD Deep Color] setting to off.

You can operate the TV functions using the button.

Power On (Press): Turns the TV on.

Power Off (Press and Hold): Turns the TV off. All running apps will close.

Menu Control (Press): You can access and adjust the menu by pressing the button when the TV is on.

Menu Selection (Press and Hold): You can use the function when you access menu control.

When the TV is turned on, press the button one time to adjust the Menu items using the button:

Turn the power off.

Change the input source.

Adjust the volume level.

Scroll through the saved channels.

Open the battery cover, replace batteries (1.5 V AAA) matching the + and – ends to the label inside the compartment, and close the battery cover.

To remove the batteries, perform the installation actions in reverse.

Make sure to point the remote control toward the remote control sensor on the TV.

To use the Magic Remote, first pair it with your TV.

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

Press the (BACK) and (HOME) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Pressing and holding the GUIDE button for more than 5 seconds will disconnect and re-register the Magic Remote at the same time.

To open the USER GUIDE, go to [Settings] -> [Support] -> [User Guide].

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

Check if the product is turned on.

Check if the power cord is connected to a wall outlet.

Check if there is a problem in the wall outlet by connecting other products.

Check the power control settings. The power supply may be interrupted.

Check if the auto-off function is activated in the settings menu.

If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth.

Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

Make sure to wring any excess water or cleaner from the cloth.

Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

Cracking noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending upon the product. This generated sound does not affect the performance and reliability of the product.

Connect the USB to Serial(RS-232C) converter/RS-232C(Serial) input jack to an external control device (such as a computer or an A/V control system) to control the product’s functions externally.

The type of control port on the TV can be different between model series.

You need to purchase the RS-232C (DE9, D-Sub 9pin female-to-female type) to RS-232C(Serial) cable required for the connection between the PC and the TV.

Alternatively, for Phone jack Type, you need to purchase the phone-jack to RS-232C cable required for the connection between the PC and the TV.