LG 60UN6951ZUA (02) PDF Document

When moving or lifting the LG 60UN6951ZUA, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size:

It is recommended to move the TV in the box or packing material that the TV originally came in.

Before moving or lifting the TV, disconnect the power cord and all cables.

When holding the TV, the screen should face away from you to avoid damage.

Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grille area.

Use at least two people to move a large TV.

When transporting the TV by hand, hold the TV upright.

When transporting the TV, do not expose the TV to jolts or excessive vibration.

When transporting the TV, keep the TV upright; never turn the TV on its side or tilt towards the left or right.

When handling the TV, be careful not to damage the protruding buttons.

Avoid touching the screen at all times, as this may result in damage to the screen.

Do not place the product on the floor with its front facing down without padding. Failure to do so may result in damage to the screen.

When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.

1. Lift and tilt the TV into its upright position on a table.

2. Leave a minimum of 10 cm (4 inches) space from the wall for proper ventilation.

3. Connect the power cord to a wall outlet.

Note: Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. Doing so may damage the product. If you install the TV on a stand, you need to take actions to prevent the product from overturning. Otherwise, the product may fall over, which may cause injury. Do not use any unapproved items to ensure the safety and product life span. Any damage or injuries caused by using unapproved items are not covered by the warranty. Make sure that the screws are fastened tightly. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not fasten the screws with excessive force otherwise they may strip and become loose.

1. Insert and tighten the eye-bolts, or TV brackets and bolts on the back of the TV. If there are bolts inserted at the eye-bolts position, remove the bolts first.

2. Mount the wall brackets with the bolts to the wall. Match the location of the wall bracket and the eye-bolts on the rear of the TV.

3. Connect the eye-bolts and wall brackets tightly with a sturdy rope. Make sure to keep the rope horizontal with the flat surface.

Use a platform or cabinet that is strong and large enough to support the TV securely.

Brackets, bolts and ropes are not provided. You can obtain additional accessories from your local dealer.

Connect an antenna, cable, or cable box to the TV while referring to the following:

Make sure not to bend the copper wire of the RF cable.

Complete all connections between devices, and then connect the power cord to the power outlet to prevent damage to your TV.

Use a signal splitter to use 2 TVs or more.

DTV Audio Supported Codec: MPEG, Dolby Digital.

This TV cannot receive ULTRA HD (3840 x 2160 pixels) broadcasts directly because the related standards have not been confirmed.

You can simply operate the TV functions using the button on the TV.

Power On (Press): Turn the TV on.

Power Off (Press and Hold): Turn the TV off. All running apps will close.

Menu Control (Press): You can access and adjust the menu by pressing the button when the TV is on.

Menu Selection (Press and Hold): You can use the function when you access menu control.

When the TV is turned on, press the button one time. You can adjust the Menu items using the button:

Power Icon: Turns the power off.

Input Icon: Changes the input source.

+ / – : Adjusts the volume level.

Up / Down arrows: Scrolls through the saved channels.

POWER: Turns the TV on or off.

TV: Returns to the last TV channel.

SEARCH (Magnifying Glass): Check for recommended content. Shows the search mode.

CC/SUB: Activates or deactivates the subtitles.

Q. Settings (Gear Icon): Accesses the Quick Settings.

INPUT: Changes the input source.

Number buttons: Enters numbers.

9**: Accesses the [Quick Help].

– (DASH): Inserts a — between numbers such as 2-1 and 2-2.

LIST: Accesses the saved channels list.

… (MORE ACTIONS): Displays more remote control functions.

QUICK ACCESS**: Edits QUICK ACCESS. This feature allows you to enter a specified app or Live TV directly by pressing and holding the number buttons.

+ VOL -: Adjusts the volume level.

FAV: Accesses your favorite channel list.

GUIDE: Displays the program event according to time scheduler.

MUTE: Mutes all sounds.

MUTE**: Accesses the [Accessibility] menu.

^ CH v: Scrolls through the saved channels.

PAGE: Moves to the previous or next screen.

Streaming Service buttons: Connects to the Video Streaming Service.

HOME (House Icon): Accesses the Home menu.

HOME**: Shows the previous history.

BACK: Returns to the previous screen.

EXIT: Clears on-screen displays and returns to last input viewing.

Navigation buttons (up/down/left/right): Scrolls through menus or options.

OK (Center button): Selects menus or options and confirms your input.

INFO: Shows information on the current program.

SAP: Enables SAP (Secondary Audio Program) Feature.

REC: Starts to record. (Only Time MachineReady supported model).

Control buttons: Control buttons for media contents.

Colored buttons: These access special functions in some menus.

Note: ** To use the button, press and hold for more than 1 second.

How to register the Magic Remote Control:

1. Put batteries into the Magic Remote and turn the TV on.

2. Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

Note: If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control:

Press the BACK and HOME buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

Note: Press and hold the GUIDE button for more than 5 seconds to disconnect and re-register the Magic Remote at the same time.

If you cannot control the TV with the remote control, verify the following:

Check if anything such as tape has been placed over the receiver.

Check if there is any obstacle between the product and the remote control.

Replace the batteries with new fresh ones.

When cleaning, unplug the power cord and wipe gently with a soft/dry cloth.

Do not spray water or other liquids directly on the TV.

Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

When cleaning the product, be careful not to allow any liquid or foreign objects to enter the gap between the upper, left or right side of the panel and the guide panel.

Make sure to wring any excess water or cleaner from the cloth.

Make sure to spray just enough of water or cleaner onto a dry cloth to wipe the screen.

The following table lists the Key Codes (Hexa) and their corresponding functions for external control device setup:

To configure the Set ID for external control:

1. Press SETTINGS to access the main menus.

2. Press the Navigation buttons to scroll to (*General -> About this TV or OPTION) and press OK.

3. Press the Navigation buttons to scroll to SET ID and press OK.

4. Scroll left or right to select a set ID number and select CLOSE. The adjustment range is 1-99.

5. When you are finished, press EXIT.

Note: The “Real Data Mapping” for the Set ID is as follows (Hexadecimal to Decimal):